Influence of different hard-facing procedures on quality of surfaces of regenerated gears

• Autorzy: Nikolić Ružica R. , Marković Svetislav , Arsić Dušan , Lazić Vukić , Hadzima Branislav , Ulewicz Robert

Identyfikatory

DOI

10.30657/pea.2021.27.34

• Języki publikacji: EN

Abstrakty

EN

During the process of regeneration of machine parts, certain phenomena occur that have a significant impact on the loss of their working ability. Hereditary properties are expressed by the interdependence of geometric and physical-mechanical-metallurgical parameters of gear teeth created during the technological operations of regeneration of worn teeth by hard-facing. The influence of the type of additional material (electrodes and their combinations) on the tribological characteristics of welded gear teeth was considered, whereby the so-called hard additional materials were applied. Those are the additional materials that give the required surface hardness of the teeth without subsequent thermal or thermochemical treatment. This research did not involve the regeneration of specific worn gears removed from machine systems, but the new gears were made, which were then damaged and then regenerated by hard-facing using the shielded metal arc welding (SMAW) procedure. Thus, all the tested gears were made of the same material, belonged to one batch and were machined on the same machines with the same machining regimes. The tests were performed on samples made of 20MnCr5 steel for cementation, on a tribometer by the “block on disc” method, which was designed to simulate the operating conditions of coupled teeth of concrete gears in the exploitation conditions. Based on the conducted tribological tests, the average coefficients of friction and topography of the surfaces were determined by measuring the wear trace and it was defined which additional materials give the best tribological characteristics of the surfaces of gears regenerated by hard-facing.

Słowa kluczowe

EN

regeneration; hard-facing; gear; tribological properties; friction coefficient

PL

regeneracja; napawanie; koło zębate; właściwości tribiologiczne; współczynnik tarcia

• Wydawca: Oficyna Wydawnicza Stowarzyszenia Menedżerów Jakości i Produkcji
• Czasopismo: Production Engineering Archives
• Rocznik: 2021
• Tom: Vol. 27, Iss. 4
• Strony: 257--264
• Opis fizyczny: Bibliogr. 31 poz., rys., tab.

Twórcy

autor

Nikolić Ružica R.

• Faculty of Technical Sciences Čačak, University of Kragujevac, 32000 Čačak, Serbia

autor

Marković Svetislav

• Faculty of Engineering, University of Kragujevac, 34000 Kragujevac, Serbia

autor

Arsić Dušan

• Faculty of Engineering, University of Kragujevac, 34000 Kragujevac, Serbia

autor

Lazić Vukić

• Faculty of Engineering, University of Kragujevac, 34000 Kragujevac, Serbia

autor

Hadzima Branislav

• Research Center; University of Žilina, 010 26 Žilina, Slovakia

autor

Ulewicz Robert

• Department of Production Engineering and Safety, Czestochowa University of Technology, Czestochowa, Poland

Bibliografia

• 1. Arsić, D., Lazić, V., Nikolić, R., Mutavžić, M., Sedmak, A., Hadzima, B., 2016a. Possibility for realizing savings by application of the hard-facing as the revitalization technology of various machine parts, in Technical aspects of materials quality. Eds. Pietraszek, J., Klimecka-Tatar, D., Managers of Quality and Production Association, Czestochowa, Poland, Chapter 8, 111–144.
• 2. Arsić, D., Lazić, V., Mitrović, S., Džunić, D., Aleksandrović, S., Djordjević, M., Nedeljković, B., 2016b. Tribological Behavior of Four Types of Filler Metals for Hard Facing Under Dry Conditions. Industrial Lubrication and Tribology, 68(6), 729–736, DOI: 10.1108/ILT-10-2015-0156
• 3. Atxaga, G., Irisarri, A.M., 2010. Failure analysis of the end of a shaft of an engine. Engineering Failure Analysis, 17(4), 714–721, DOI: 10.1016/j.engfailanal.2009.08.010
• 4. Bai, H., Zhu, C., Zhou, Y., Chen, X., Feng, H., Ye, W., 2020. Study on Tooth Interior Fatigue Fracture Failure of Wind Turbine Gears. Metals, 10(11), 1497, DOI: 10.3390/met10111497
• 5. Borrego, L.P., Pires, J.T., Costa, J.M., Ferreira, J.M., 2009. Mould steels repaired by laser welding. Engineering Failure Analysis, 16(2), 596–607, DOI: 10.1016/j.engfailanal.2008.02.010
• 6. Czuprynski, A., 2020. Comparison of properties of hardfaced layers made by a metal-core-covered tubular electrode with a special chemical composition. Materials, 13, 5445, DOI: 10.3390/ma13235445
• 7. Dadon, I., Koren, N., Klein, R., Lipsett, M.G., Bortman, J., 2020. Impact of gear tooth surface quality on detection of local faults. Engineering Failure Analysis, 108, 104291, DOI: 10.1016/j.engfailanal.2019.104291
• 8. Desir, J.L., 2001. Examples of Repair Welding of Heavy Machinery Subject to Breakage due to Low Frequency Alternating Stresses. Engineering Failure Analysis, 8(5), 423–434, DOI: 10.1016/S1350-6307(00)00046-7
• 9. Durmuş, H., Çömez, N., Gül, C., Yurddaşkal, M., Yurddaşkal, M., 2018. Wear performance of Fe-Cr-C-B hardfacing coatings: Dry sand/rubber wheel test and ball-on-disc test. International Journal of Refractory Metals and Hard Materials, 77, 37–43, DOI: 10.1016/j.ijrmhm.2018.07.006
• 10. EN 14700:2014: Welding consumables — Welding consumables for hard-facing.
• 11. EN 1599:1997: Welding consumables — Covered electrodes for manual arc welding of creep-resisting steels - Classification.
• 12. Feng W., Feng Z., Mao L., 2020. Failure analysis of a secondary driving helical gear in transmission of electric vehicle. Engineering Failure Analysis, 117, 104934, DOI: 10.1016/j.engfailanal.2020.104934
• 13. Gualco, A., Marini, C., Svoboda, H., Surian, E., 2015. Wear resistance of Fe-based nanostructured hardfacing. Procedia Material Science, 8, 934–943, DOI: 10.1016/j.mspro.2015.04.154
• 14. Hao, F., Liao, B., Li, D., Liu, L., Dan, T., Ren, X., Yang, Q., 2011. Effects of rare earth oxide on hardfacing metal microstructure of medium carbon steel and its refinement mechanism. Journal of Rare Earths, 29(6), 609–613, DOI: 10.1016/S1002-0721(10)60507-8
• 15. Lazić, V., Sedmak, A., Aleksandrović, S., Milosavljević, D., Čukić, R., Grabulov, V., 2009. Reparation of damaged mallet for hammer forging by hard facing and weld cladding. Tehnički vjesnik - Technical Gazette, 16(4), 107-113, https://hrcak.srce.hr/45753
• 16. Lazić, V., Čukić, R., Aleksandrović, S., Milosavljević, D., Arsić, D., Nedeljković, B., 2014. Techno-economic justification of reparatory hard facing of various working parts of mechanical systems. Tribology in Industry, 36(3), 287–292, http://www.tribology.fink.rs/journals/2008/2008-1-2/1.pdf
• 17. Lazić, V., Arsić, D., Nikolić, R., Mutavdžić, M., Meško, J., 2016. Reparation by Hard Facing of the Damaged Secondary Stone Crusher. Manufacturing Technology, 16(2), 375–380, https://www.journalmt.com/artkey/mft-201602-0012_reparation-by-hard-facing-of-the-damaged-secondary-stone-crushers.php
• 18. Li, D., Yang, Y., Liu, L., Zhang, J., Yang, Q., 2009. Effects of RE oxide on the microstructure of hardfacing metal of the large gear. Material Science and Engineering A, 509, 94–97, DOI: 10.1016/j.msea.2009.02.018
• 19. Markovic, S., Milovic, Lj., Marinkovic, A., Lazovic, T., 2011. Tribological aspect of selecting filler metal for repair surfacing of gears by hardfacing. Structural Integrity and Life, 11(2), 127–130, http://divk.inovacionicen-tar.rs/ivk/ivk11/127-130-IVK2-2011-SM-LM-AM-TL.pdf
• 20. Marković, S., Arsić, D., Nikolić, R., Lazić, V., Hadzima, B., Milovanović, V., Dwornicka, R., Ulewicz, R., 2021. Exploitation characteristics of teeth flanks of gears regenerated by three hard-facing procedures. Materials, 14(15), paper no. 4203, DOI: 10.3390/ma14154203
• 21. Marković, S., Arsić, D., Nikolić, R.R., Lazić, V., Ratković, N., Hadzima, B., Szmidla, J., Ulewicz, R., 2021. Analysis of the Welding Type and Filler Metal Influence on Performance of a Regenerated Gear. Materials, 14(6), 1496, DOI: 10.3390/ma14061496
• 22. Mohammed, O.D., Rantatalo, M., 2020. Gear Fault Models and Dynamics-Based Modelling for Gear Fault Detection - A Review. Engineering Failure Analysis, 117, 104798, DOI: 10.1016/j.engfailanal.2020.104798
• 23. Suraj, R., 2021. Hardfacing and its effect on wear and corrosion performance of various ferrous welded mild steels. Materials Today: Proceedings, 42, 842–850, DOI: 10.1016/j.matpr.2020.11.592
• 24. Tomić, R., 2019. Influence of Tribological Pairs on Structural and Material Damage. Structural Integrity and Life, 19 (1), 58–66, http://divk.inovacionicentar.rs/ivk/ivk19/058-IVK1-2019-RT.pdf
• 25. Trško, L., Lago, J., Jambor, M., Nový, F., Bokůvka, O., Florková, Z., 2020. Microstructure and residual stress analysis of Strenx 700 MC welded joint. Production Engineering Archives, 6, 41–44, DOI: 10.30657/pea.2020.26.09
• 26. Ulewicz, R., Novy, F.R., 2016. The influence of the surface condition on the fatigue properties of structural steel. Journal of Balkan Tribological Association, 22, 1147–1155, https://scibulcom.net/en/article/39wnZZhcNDoMsJzVTXq8
• 27. Vasić, M., Stojanović, B., Blagojević, M., 2020. Fault Analysis of Gearboxes in Open Pit Mine. Applied Engineering Letters, 5(2), 50–61, DOI: 10.18485/-aeletters.2020.5.2.3
• 28. icen, M., Bokuvka, O., Nikolić, R., Bronček, J., 2020. Tribological behavior of low-alloyed steel after nitriding. Production Engineering Archives, 26(3), 78–83, DOI: 10.30657/pea.2020.26.16
• 29. Vicen, M., Bronček, J., Nový, F., 2019. Investigation of tribological properties of CarbonX coating deposited on 100Cr6 steel. Production Engineering Archives, 25, 52–55, DOI: 10.30657/pea.2019.25.10
• 30. Xing, S., Yu, S., Deng, Y., Dai, M., Yu, L., 2012. Effect of Cerium on abrasive wear behaviour of hardfacing alloy. Journal of Rare Earths, 30, 69–73, DOI: 10.1016/S1002-0721(10)60641-2
• 31. Yousfi, B.E., Soualhi, A., Medjaher, K., Guillet, F., 2020. New Approach for Gear Mesh Stiffness Evaluation Of Spur Gears With Surface Defects. Engineering Failure Analysis, 116, 104740, DOI: 10.1016/j.engfailanal.2020.104740