Magnetic induction of polymer composites filled with ferrite powders

• Autorzy: Stabik J. , Dybowska A. , Pluszyński J. , Szczepanik M. , Suchoń Ł.
• Języki publikacji: EN

Abstrakty

EN

Purpose: The goal of this work was to determine influence of amount and type of ferrite fillers on magnetic induction of epoxy composites. Six mixtures that contain different amount of ferrite powder were prepared. Additionally an effect of type and amount of introduced ferrite powder on epoxy resin processing conditions and parameters was searched. Design/methodology/approach: In this research the method of preparing polymeric gradient composites was centrifugal casting. The experimental procedure focused on evaluating the magnetic induction of gradient composites. Magnetic induction of composites based on epoxy resin, which contain ferrite powders was measured using milliteslometer. Measurements were performed for three filler contents and for two types of filler. Findings: Centrifugal casting method allowed obtaining materials with different percentage of ferrite content in subsequent layers of cylindrical composites. Moreover it was observed that values of magnetic induction were higher for composite with barium ferrite than for composite with strontium ferrite but the difference was not too high. Research limitations/implications: The main problem of this work was about limitation of maximum level of fillers content. Adding more filler than 30%vol caused very rapid composite viscosity increase and made air removing and casting impossible. For that reason there were made composites with 10%vol., 20%vol. and 30%vol. of ferrite powders. Trials were performed with mixtures that contained up to 50%vol. of filler. Practical implications: Method applied in this research allowed to obtain materials that are characterized by gradient of magnetic properties. Such composites find applications in electrotechnical industry and in mechanical engineering. Originality/value: New polymeric gradient materials were developed using centrifugal casting technology. Magnetic properties of these composites were determined depending on distance from the surface of the test piece.

Słowa kluczowe

EN

polymers; magnetic properties; casting

PL

polimery; właściwości magnetyczne; odlewanie

• Wydawca: International OCSCO World Press
• Czasopismo: Archives of Materials Science and Engineering
• Rocznik: 2010
• Tom: Vol. 41, nr 1
• Strony: 13--20
• Opis fizyczny: Bibliogr. 26 poz.

Twórcy

autor

Stabik J.

autor

Dybowska A.

autor

Pluszyński J.

autor

Szczepanik M.

autor

Suchoń Ł.

• Division of Metal and Polymer Materials Processing, Institute of Engineering Materials and Biomaterials, Silesian University of Technology, ul. Konarskiego 18a, 44-100 Gliwice, Poland,

Bibliografia

• [1] R.A. Krektuleva, Computer-aided design of high-strength gradient materials operating under dynamic loads, Strength of Materials 35/1 (2003) 82.
• [2]J. Stabik, A. Dybowska, Methods of preparing polymeric gradient composites, Journal of Achievements in Materials and Manufacturing Engineering 25/1 (2007) 67-70.
• [3]J. Jang, S. Han, Mechanical properties of glass-fibre mat/PMMA functionally gradient composite, Composites A30 (1999) 1045-1053.
• [4]P. Tsotra, K. Friedrich, Electrical and mechanical properties of functionally graded epoxy-resin/carbon fibre composites, Composites Part A 34 (2003) 75-82.
• [5]M. Krumova, C. Klingshirn, F. Haupert, K. Friedrich, Microhardness studies on functionally graded polymer composites, Composites Science and Technology 61 (2001) 557-563.
• [6]Y. Agari, Y. Anan, R. Nomura, Y. Kawasaki, Estimation of the compositional gradient in a PVC/PMMA graded blend prepared by the dissolution-diffusion method, Polymer 48 (2007) 1139-1147
• [7]J. Stabik, A. Dybowska, Electrical and tribological properties of gradient epoxy-graphite composites, Journal of Achievements in Materials and Manufacturing Engineering 27/1 (2008) 39-42.
• [8]M. Szczepanik, J. Stabik, M. Łazarczyk, A.Dybowska, Influence of graphite on electrical properties of polymeric composites, Archives of Materials Science and Engineering 37/1 (2009) 37-44
• [9]J. Stabik, G. Wróbel, A. Dybowska, M. Szczepanik, J. Pluszyński, Magnetic Graded Composites, Materiały konferencyjne Proceedings of II International Conference on modern achievements of science and education, Natanya, Israel, 2008, 61-64
• [10]H.D. Young, R.A. Freedman, Sears and Zemansky's university physics. Vol. 2, Pearson Addison Wesley, San Francisco, 2004.
• [11]Encyclopaedia, PWN, 1988 (in Polish)
• [12]Encyclopaedia Britannica www.britannica.com.
• [13]M. Nałęcz, J. Jaworski, Magnetic measurements, WNT, Warsaw, 1968.
• [14]H. Shokrollahi, K. Janghorban, Soft magnetic composite materials (SMCs), Journal of Materials Processing Technology 189 (2007) 1-12.
• [15]J. Kuryłowicz, Research of magnetic materials, WNT, Warsaw, 1962 (in Polish).
• [16]B.M. Yavorsky, A.A. Pinsky, Fundamentals of physics, Vol.1, Mir Publishers, Moscow, 1987.
• [17]J. Konieczny, L.A. Dobrzański, A. Przybył, J.J. Wysłocki, Structure and magnetic properties of powder soft magnetic materials, Journal of Achievements in Materials and Manufacturing Engineering 20 (2007) 139-142.
• [18]M. Drak, L. A. Dobrzański, Hard magnetic materials Nd-Fe-B/Fe with epoxy resin matrix, Journal of Achievements in Materials and Manufacturing Engineering 24/2 (2007) 63-66.
• [19]H. Kronmuller, S. Parkin, Handbook of Magnetism and Advanced Materials, Vol.4 - Novel Materials, John Wiley & Sons, Chichester, 2007.
• [20]R. Feynman, R.B. Leighton, M.L. Sands, Feynman lectures on physics. Vol. 2 - Mainly electromagnetism and matter, Pearson Addison Wesley, San Francisco, 2006.
• [21]M. Leonowicz, J.J. Wysł+ocki, Modern magnets - technology, coercivity mechanism, applications, WNT, Warsaw, 2005 (in Polish)
• [22]C.M. Hurd, Varieties of magnetic order in solids, Contemporary Physics 23/5 (1982) 469-493.
• [23]M. Funabashi, Gradient composites of nickel coated carbon fibre filled epoxy resin moulded under centrifugal force, Composites Part A 28A (1997) 731-737.
• [24]S.A.R. Hashim, U.K. Dwivedi, Estimation of concentration of particles in polymerizing fluid during centrifugal casting of functionally graded polymer composites, Journal of Polymer Research 14 (2007) 75-81.
• [25]Y. Watanabe, A. Kawamoto, K. Matsuda, Particle size distributions in functionally graded materials fabricated by the centrifugal solid-particle method, Composites Science and Technology 62 (2002) 881-888.
• [26]S.R.A. Hashmi, U.K. Dwivedi, Estimation of concentration of particles in polymerizing fluid during centrifugal casting of functionally graded polymer composites, Journal of Polymer Research 14 (2007) 75-81.