PL
 |
EN
Ten serwis zostanie wyłączony 2025-02-11.
Nowa wersja platformy, zawierająca wyłącznie zasoby pełnotekstowe, jest już dostępna.
Przejdź na https://bibliotekanauki.pl
Preferencje help
Polish version English version Język
Widoczny [Schowaj] Abstrakt
Liczba wyników

Znaleziono wyników: 4

Liczba wyników na stronie
first rewind previous Strona / 1 next fast forward last
Wyniki wyszukiwania
help Sortuj według:

help Ogranicz wyniki do:
first rewind previous Strona / 1 next fast forward last
1
Content available Enhancing the Strength of Al/Mg Dissimilar Friction Stir Lap Welded Joint by Zn Filler Addition Combined with an Appropriate Heat Input
100%
Zhao H. , Gong P. , Ji S. , Gong X.
Archives of Metallurgy and Materials
|
2022
|
tom Vol. 67, iss. 1
137--146
EN
7075-T6 Al and AZ31B Mg dissimilar alloys were friction stir lap welded with or without a Zn filler, and the effect of heat input on the joint quality was systematically studied. The experimental and finite element simulation results displayed that the formation characteristics and microstructures of the joint with or without the Zn filler were significantly affected by the heat input. The tensile shear load of joint with or without the Zn filler increased first and then decreased with the decrease of the welding speed from 200 to 50 mm/min. Moreover, the peak temperature in the stir zone was significantly decreased by the Zn filler addition, and the high temperature zone narrowed along the plate thickness direction. These changes of heat input made that longer mixing region boundary length and larger effective lap width were attained as the Zn filler was used. In addition, due to the replacement of Al-Mg intermetallic compounds (IMCs) by Al-Mg-Zn and Mg-Zn IMCs which were less harmful to the joint, the tensile shear load of the joint with the Zn filler was obviously enhanced compared to that of the joint without the Zn filler at each welding speed. The maximum tensile shear load of 7.2 kN was obtained at the welding speed of 100 mm/min.
2
Content available Comparative Study of 2060-T8 Al-Li Alloy Friction Stir Welded Joints Between Natural Cooling and Water Cooling
100%
Ma L. , Niu S. , Ji S. , Gong P.
Archives of Metallurgy and Materials
|
2020
|
tom Vol. 65, iss. 1
305--312
EN
2060-T8 Al-Li alloy was friction stir butt welded under natural and water cooling conditions. Microstructures and mechanical properties of the welding joints were mainly compared and discussed. By spraying water on the top surface of stir zone, the grain size was reduced, attributing to the improvement of microhardness. The maximum tensile strength under the water cooling reached 461.1 MPa. The joint fractured at the stir zone due to the thickness reduction and the joint softening. The fracture surface consisted of many dimples with various sizes, indicating the typical ductile fracture. The strategy to apply the low heat input at the welding stage and high cooling rate at the cooling stage during FSW is necessary to obtain a high-quality FSW joint.
3
Content available Microstructure and mechanical properties of friction stir lap welded dissimilar Al/Ti alloys by ultrasonic assistance
88%
Dong Z. , Zhang Z. , Hu W. , Gong P. , Lv Z.
Archives of Metallurgy and Materials
|
2022
|
tom Vol. 67, iss. 1
91--96
EN
Dissimilar Al/Ti alloy sheets were lap welded with ultrasonic assistance in this work. The influence of ultrasonic vibration on formation, intermetallic compounds (IMCs) and tensile failure load of the obtained joints was discussed. The results showed that voids formed at the lap interface without ultrasonic assistance. No voids can be observed on the joint welded with ultrasonic because the vibration during welding improved the material flow. No obvious IMC formed at the Al/Ti bonding interface of the joint welded without ultrasonic assistance. An IMC layer formed at the bonding interface of Al/Ti with ultrasonic assistance and its thickness increased with decreasing the welding speed. The failure load of the joint welded with ultrasonic assistance was higher than the joint without ultrasonic because the void was eliminated and the thin IMC layer formed at the bonding interface was beneficial to joint strength. All joints presented shear failure mode during the tensile shear tests.
4
Content available The experimental instrumented bolt with fibre bragg grating force sensors
75%
Wang T. , Chang J. , Gong P. , Shi W. , Li N. , Cheng S.
Archives of Mining Sciences
|
2020
|
tom Vol. 65, no. 1
179--194
EN
Monitoring the stress change of bolt and knowing the anchoring condition in a reasonable and effective way, accurately, can effectively prevent tunnel accident from breaking out. The stress of rock mass around the roadway is usually transferred to the anchor rod in the form of axial load, so it is of great significance to study the axial load of the bolt. In this paper, a full size anchoring and drawing experiment system was designed and established, innovatively, which realized the pull-out test of 2.5 m prestressed end Anchorage and the full-length Anchorage by using the new resin anchorage agent under vertical and horizontal loads. Through the application of fiber Bragg grating (FBG) sensing technology to the test of full-scale anchor rod, the axial force distribution characteristics of the end Anchorage and the full-length Anchorage anchor rod were obtained under the action of pre-tightening torque and confining rock pressure. The comparison indicates that the proportion of high stress range accounts for only 17.5% and the main bearing range is near the thread end of anchor rod, the proportion of main bearing range of end Anchorage is 83.3%, and the feasibility of FBG force-measuring anchor rod is verified in the field. The research results have certain reference value.
first rewind previous Strona / 1 next fast forward last
JavaScript jest wyłączony w Twojej przeglądarce internetowej. Włącz go, a następnie odśwież stronę, aby móc w pełni z niej korzystać.