Warianty tytułu
Języki publikacji
Abstrakty
In this paper a physical model of friction welding of elastic materials and plastic metals is presented. The model has been practically verified in the process of friction welding of corundum ceramics, containing 97.5% of Al2O3, and Al as well as in the process of friction welding of the same ceramics and Cu. In the process of Al2O3-Al welding the following conditions, i.e. values of the process parameters were applied: diameter of cylindrical bonded elements - 10 mm, pressure in the stage of friction heating - 18 MPa, rotational speed of the ceramic element - 14500 r.p.m., heating time - 0.85 s. pressure in the stage of forging - 46 MPa, time of Al forging - 3.5 s. Mechanical strength of the acquired welded joints was sufficient. Also, diffusion of Al into Al2O3 was observed in the bonding zone. The mathematical modelling of the friction welding process is also demonstrated. Simulation of the process was performed by means of finite element (FEM) method using two FEM systems, namely ADINA-T and ADINA. The process conditions in the numerical simulation were the same as those in the technological process. In ADINA-T the temperature field, which changed with time, was determined. The field was then superimposed onto the mechanical one (ADINA). The simulations made it possible to observe the thermo-mechanical phenomena that take place during the process. The obtained results show that the pressure and temperature distribution on the contact surfaces of the bonded elements is non-homogeneous. This fact has a significant influence on the quality of the welded joint. The performed calculations and studies on the influence of the diffusion phenomena on the welding process showed that the diffusion depth is approx. 4 micrometres and the calculated diffusion coefficient of Al into Al2O3 is 1.8x10 to the -13 square metres/s. Diffusion of Al into Al2O3 generates also internal stresses in the intermediate layer between the welded elements.
Czasopismo
Rocznik
Tom
Strony
5-27
Opis fizyczny
Twórcy
autor
autor
- Institute of Materials Technology, Faculty of Production Engineering, Warsaw University of Technology, wydział4@pan.pl
Bibliografia
- [1] S. Jones, Can ceramics be friction welded to metals?. TWI, www.twi.co.uk (2003).
- [2] W. Włosiński, T. Chmielewski, A. Grabowska, A. Góra, Przegląd spawalnictwa, 12, 1 (2003).
- [3] W. Włosiński, T. Chmielewski, Torzewski, Proc. lllst Int. Conf. on Advanced in Production Engineering, Warsaw, 9 (2004).
- [4] A. Służalec, Int. J. Mech. Sci., 32, 467 (1990).
- [5] L. Fu, L. Duan, J. Weld, 77, 202 (1998).
- [6] L.D. Alvise, E. Massoni, S.J. Walloe, J. Mat. Processing Technology, 387 (2002).
- [7] A. Ambroziak, Zgrzewanie metali trudnotopliwych w cieczy na tle innych metod spajania. Ofic. Wyd. Pol. Wrocławskiej, Wrocław (1998).
- [8] Sahin Ahmed, J. Mat. Processing Technology, 82, 127 (1998).
- [9] K.J. Bathe, Finite Element Procedures, New Jersey (1996).
- [10] J. Zimmerman, Przegląd Spawalnictwa, 9, 17 (2005).
- [11] J. Zimmerman, Przegląd Spawalnictwa, 10, 32 (2005).
- [12] Z. Lindemann, K. Skalski, W. Włosiński, J. Zimmerman, Biulletin of the Polish Academy of Sciences (in press).
- [13] Y. Yamada, Int. J. Mech. Sci. 10, 343 (1968).
- [14] M. Perzyk, Mater. Sci. Technology, 1, 84 (1985).
- [15] W. Włosiński: Elektroceramika własności i badania, PWN, Warszawa (1981).
- [16] K. Przybyłowicz. Metaloznawstwo teoretyczne, Akademia Górniczo Hutnicza. Kraków (1999).
- [17] M. Danielewski, Archives of Metallurgy and Materials, 49, 189 (2004).
- [18] K. Sikorski, Archives of Metallurgy and Materials, 49, 369 (2004).
- [19] E. Mittemeijer, Gitterverzerrungen In nitriertem Eisen und Stahl, HTM, 36, 57 (1981).
Typ dokumentu
Bibliografia
Identyfikatory
Identyfikator YADDA
bwmeta1.element.baztech-article-BOS3-0010-0026