Enhancement of adiabatic effectiveness in a combustion chamber liner with effusion cooling through conical and fan shaped holes

• Autorzy: Kumar, Yellu , Qayoum, Adnan , Saleem, Shahid
• Języki publikacji: EN

Abstrakty

EN

The present study involves computational investigation of effusion cooling over a flat plate through the different shaped holes. The interaction between the film jet and the mainstream flow creates a counter-rotating vortex pair, resulting jet detachment from the surface and insufficient film cooling coverage over the surface. To enhance the effusion cooling performance, shaped holes are used in place of standard cylindrical holes to reduce the effects of the counter-rotating vortex pair. Two different shaped holes i.e., conical-shaped and fan-shaped holes are used in the investigation and compared to the cylindrical holes. A commercial finite element method package COMSOL Multiphysics 5.5 is used to simulate and analyse the three-dimensional combustor liners of gas turbine. Data is presented for total 10 rows of effusion holes with injection angles 30o at blowing ratios 0.25, 1.0 and 3.2. The shaped holes provide better cooling effectiveness by increasing the lateral spread of coolant over the surface wall. The results show that both the shaped hole geometries can generate additional anti-counter rotating vortex pairs, which contribute to reducing the strength of the counter-rotating vortex pair. The coolant penetration and strong shear zones at the interaction of coolant jet and main stream in shaped holes are greatly reduced in comparison with cylindrical holes. For a low blowing ratio of 0.25, the conical-shaped holes exhibited adiabatic effectiveness that was 25% and 19% greater than the cylindrical and trapezoidal-shaped holes respectively. On the other hand, fan-shaped holes provide enhanced adiabatic effectiveness at increased blowing ratios. At higher value of blowing ratio 3.2, the adiabatic effectiveness increased by 13% compared to cylindrical holes and 4% compared to conical-shaped holes. In addition, velocity profiles and two-dimensional streamlines have been examined in order to study the flow behavior on the surface.

Słowa kluczowe

EN

gas turbine; combustion chamber liners; effusion cooling; adiabatic effectiveness; conical-shaped holes

• Czasopismo: Archives of Thermodynamics
• Rocznik: 2024
• Tom: Vol. 45, no 2
• Strony: 183--193
• Opis fizyczny: Bibliogr. 29 poz., rys.

Twórcy

autor

Kumar, Yellu

• Mechanical Engineering Department, National Institute of Technology Srinagar, J&K, 190006, India,

autor

Qayoum, Adnan

• Mechanical Engineering Department, National Institute of Technology Srinagar, J&K, 190006, India

autor

Saleem, Shahid

• Mechanical Engineering Department, National Institute of Technology Srinagar, J&K, 190006, India

Bibliografia

• [1] Yuen, C.H.N., & Martinez-Botas, R.F. (2005). Film cooling characteristics of rows of round holes at various streamwise angles in a crossflow: Part I. Effectiveness. International Journal of Heat and Mass Transfer, 48(23−24), 4995−5016. doi: 10.1016/j.ijheatmasstransfer.2005.05.019
• [2] Qayoum, A., & Panigrahi, P. (2019). Experimental investigation of heat transfer enhancement in a two-pass square duct by permeable ribs. Heat Transfer Engineering, 40(8), 640−651. doi:10.1080/01457632.2018.1436649
• [3] Rasool, A., & Qayoum, A. (2018). Numerical analysis of heat transfer and friction factor in two-pass channels with variable rib shapes. International Journal of Heat and Technology, 36(1). doi:10.18280/ijht.360106
• [4] Rasoo, A., & Qayoum, A. (2018). Numerical investigation of fluid flow and heat transfer in a two-pass channel with perforated ribs. Pertanika Journal of Science and Technology, 26(4).
• [5] Goldstein, R. J. (1971). Film cooling. In Advances in Heat Transfer, 7 (pp. 321−379). Elsevier.
• [6] Andrews, G.E., Alikhanizadeh, M., Tehrani, F.B., Hussain, C.I., & Azari, M.K. (1988). Small diameter film cooling holes: The influence of hole size and pitch. International Journal of Turbo and Jet Engines, 5(1−4), 61−72. doi: 10.1515/tjj.1988.5.1-4.61
• [7] Andrews, G.E., Asere, A.A., Gupta, M.L., & Mkpadi, M.C. (1985). Full coverage discrete hole film cooling: The influence of hole size. In ASME Turbo Expo: Power for Land, Sea, and Air, 79405, p. V003T09A003 (85-GT-47). doi: 10.1515/TJJ.1985.2.3.213
• [8] Andrews, G.E., Gupta, M.L., & Mkpadi, M.C. (1984). Full coverage discrete hole wall cooling: Cooling effectiveness. In ASME Turbo Expo: Power for Land, Sea, and Air American Society of Mechanical Engineers, 79498, V004T09A018 (84-GT-212). doi:10.1515/TJJ.1985.2.3.199
• [9] Kumar, K.R.Y., Qayoum, A., Saleem, S., & Mir, F.Q. (2022). Effect of blowing ratio on adiabatic effectiveness for effusion cooling in gas turbine combustor liners. Research on Engineering Structures and Materials, 8(3), 431−445. doi: 10.17515/resm2022.359me1028
• [10] Kumar, Y., Qayoum, A., Saleem, S., & Mir, F.Q. (2021). Combined effect of upstream ramp and effusion cooling in combustion chamber liners of gas turbines. Journal of Thermal Engineering,9(2), 297–312. doi: 10.18186/thermal.1284759
• [11] Lin, Y., Song, B., Li, B., Liu, G., & Wu, Z. (2003). Investigation of film cooling effectiveness of full-coverage inclined multihole walls with different hole arrangements. In ASME Turbo Expo: Power for Land, Sea, and Air, 36886 (651−660). doi: 10.1115/GT2003-38881
• [12] Zhang, C., Lin, Y., Xu, Q., Liu, G., & Song, B. (2009). Cooling effectiveness of effusion walls with deflection hole angles measured by infrared imaging. Applied Thermal Engineering, 29(5−6), 966−972. doi: 10.1016/j.applthermaleng.2008.05.011
• [13] Kumar, K.Y., Qayoum, A., Saleem, S., & Qayoum, F. (2020). Effusion cooling in gas turbine combustion chambers − a comprehensive review. In IOP Conference Series: Materials Science and Engineering, 804(1), 012003. IOP Publishing. doi: 10.1088/1757-899X/804/1/012003
• [14] Goldstein, R.J., Eckert, E.R G., & Burggraf, F. (1974). Effects of hole geometry and density on three-dimensional film cooling. International Journal of Heat and Mass Transfer, 17(5), 595−607.doi: 10.1016/0017-9310(74)90007-6
• [15] Fu, J.L., Bai, L.C., Zhang, C., & Ju, P.F. (2019). Film cooling performance for cylindrical holes embedded in contoured craters: effect of the crater depth. Journal of Applied Mechanics and Technical Physics, 60, 1068−1076. doi: 10.1134/S0021894419060129
• [16] Revulagadda, A.P., Adapa, B.R., Balaji, C., & Pattamatta, A. (2024). Performance assessment and optimization of three-dimensional hybrid slot–effusion jet cooling configuration of an annular combustor liner. Applied Thermal Engineering, 240,122198. doi: 10.1016/j.applthermaleng.2023.122198
• [17] Huang, Y., Zhang, J.Z., & Wang, C.H. (2020). Multi-objective optimization of round-to-slot film cooling holes on a flat surface. Aerospace Science and Technology, 100, 105737. doi: 10.1016/j.ast.2020.105737
• [18] Zhang, H., Wang, Q., Chen, Z., Su, X., & Yuan, X. (2020). Effects of compound angle on film cooling effectiveness considering endwall lateral pressure gradient. Aerospace Science and Technology, 103, 105923. doi: 10.1016/j.ast.2020.105923
• [19] Park, S.H., Kang, Y.J., Seo, H.J., Kwak, J.S., & Kang, Y.S. (2019). Experimental optimization of a fan-shaped film cooling hole with 30 degrees-injection angle and 6-hole length-to-diameter ratio. International Journal of Heat and Mass Transfer, 144,118652. doi: 10.1016/j.ijheatmasstransfer.2019.118652
• [20] Li, Z., Xie, P., Zeng, Q., & Chen, X. (2023). Study of tangential effusion cooling of a combustor liner. Processes, 11(8), 2433.doi: 10.3390/pr11082433
• [21] Schmidt, D.L., Sen, B., & Bogard, D.G. (1996). Film cooling with compound angle holes: adiabatic effectiveness. Journal of Turbomachinery, 118(4), 807−813. doi: 10.1115/1.2840938
• [22] Sofi, A.Y., & Qayoum, A. (2023). Numerical investigation of thermo-hydraulic performance and irreversibility behaviour in a pulsating turbulent flow ribbed duct. Arabian Journal for Science and Engineering, 49(2), 1515−1529. doi: 10.1007/s13369-023-07902-w
• [23] Qayoum, A., Gupta, V., Panigrahi, P.K., & Muralidhar, K. (2010). Influence of amplitude and frequency modulation on flow created by a synthetic jet actuator. Sensors and Actuators A: Physical, 162(1), 36−50. doi: 10.1016/j.sna.2010.05.008
• [24] Thole, K.A., Gritsch, M., Schulz, A., & Wittig, S. (1997). Effect of a crossflow at the entrance to a film-cooling hole. Journal of Fluids Engineering, 119(3), 533−540. doi: 10.1115/1.2819277
• [25] Bell, C.M., Hamakawa, H., & Ligrani, P.M. (2000). Film cooling from shaped holes. Journal of Heat Transfer, 122(2), 224−232.doi: 10.1115/1.521484
• [26] Sen, B., Schmidt, D.L., & Bogard, D.G. (1996). Film cooling with compound angle holes: heat transfer. Journal of Turbomachinery, 118(4), 800−806. doi: 10.1115/1.2840937
• [27] El-Gabry, L.A., & Kaminski, D.A. (2005). Numerical investigation of jet impingement with cross flow − comparison of yangshih and standard k–ϵ turbulence models. Numerical Heat Transfer, Part A, 47(5), 441−469. doi: 10.1080/10407780590891254
• [28] Silieti, M., Divo, E., & Kassab, A.J. (2004). Numerical investigation of adiabatic and conjugate film cooling effectiveness on a single cylindrical film-cooling hole. In ASME International Mechanical Engineering Congress and Exposition, 4711, 333−343.
• [29] Scrittore, J.J., Thole, K.A., & Burd, S.W. (2007). Investigation of velocity profiles for effusion cooling of a combustor liner. Journal of Turbomachinery, 129(3), 518-526. doi: 10.1115/1.2720492

Identyfikatory

DOI

10.24425/ather.2024.150864