Content of respirable and inhalable fractions in dust created at sawing beech wood and its modifications

• Autorzy: Hlásková, L. , Rogoziński, T. , Dolny, S. , Kopecký, Z. , Jedinák, M.
• Języki publikacji: EN

Abstrakty

EN

This paper presents the results of the granulometric analysis of sawdust, created during the sawing of modified and unmodified beech wood with a circular saw. The aim of this work was to analyze the effect of the treatment of beech wood (Fagus sylvatica L.) on the content of respirable and inhalable particles in sawdust generated during the sawing process using a modern circular saw. Different methods of particle-size determination were used. The results obtained from the sieve analysis prove that the sawdust created during the cutting of DMDHEU was finer than the sawdust from native beech and other modified materials. It was also discovered that the dust created during the cutting of Bendywood was finer than when machining native beech and Lignamon. There was an increase in the share of fine fraction in the range of granularity x < 100 μm at the expense of the fraction x = 0.25–1 mm. The properties of Lignamon are primarily based on the properties of raw wood material, therefore this modified material had a similar cumulative particle-size distribution to the native beech dust.

Słowa kluczowe

EN

beech; modified wood; wood dust; circular saw blade; particle-size distribution

• Czasopismo: Drewno : prace naukowe, doniesienia, komunikaty
• Rocznik: 2015
• Tom: vol. 58, nr 194
• Strony: 135--146
• Opis fizyczny: Bibliogr. 20 poz., rys., tab.

Twórcy

autor

Hlásková, L.

• Mendel University in Brno, Brno, Czech Republic,

autor

Rogoziński, T.

• Poznan University of Life Sciences, Poznań, Poland,

autor

Dolny, S.

• Wood Technology Institute, Poznań, Poland,

autor

Kopecký, Z.

• Mendel University in Brno, Brno, Czech Republic,

autor

Jedinák, M.

• Mendel University in Brno, Brno, Czech Republic,

Bibliografia

• Baran S., Teul I. [2007]: Wood dust: an occupational hazard which increases the risk of respiratory disease. Journal of Physiology and Pharmacology 58 [5]: 43–50
• Barcík Š., Gašparík M. [2014]: Effect of tool and milling parameters on the size distribution of splinters of planed native and thermally modified beech wood. BioResources 9 [1]: 1346–1360
• Beljo-Lučić R., Čavlović A.O., Jug M. [2011]. Definitions and relation of airborne wood dust fractions. Proceedings of: the 4th International Scientific Conference – Woodworking Techniques, 7–9 September 2011. Prague, Czech Republic: 25–32
• Bollmus S., Dieste A., Militz H., Rademacher P. [2009]: Properties of modified beechwood. Forst und Holz 64 [7/8]: 30–34
• Dolny S., Grocki W., Rogoziński T. [2011]: Properties of waste from the cutting of thermally modified oak wood. Acta Scientarum Polonorum - Silvarum Colendarum Ratio et Industria Lignaria 10 [1]: 11–18
• Dutkiewicz J., Prażmo Z. [2008]: Biologiczne czynniki zagrożenia zowodowego w przemyśle drzewnym (Occupational biohazards in wood industry). Zdrowie Publiczne 118 [2]: 138–144
• Dzurenda L., Orłowski K. [2011]: The effect of thermal modification of ash wood on granularity and homogeneity of sawdust in the sawing process on a sash gang saw PRW 15-M in view of its technological usefulness. Drewno 54 [186]: 27–37
• Dzurenda L., Orłowski K., Grzeskiewicz M. [2010]: Effect of Thermal Modification of Oak Wood on Sawdust Granularity. Drvna Industrija 61 [2]: 89–94
• Gerek T. [2010]: Prašnost při formátování aglomerovaných materiálů. In Czech. Dustiness at formatting agglomerated materials. Mendel University in Brno, Czech Republic. Faculty of Forestry and Wood Technology. Department of Forest and Forest Products Technology. [Diploma thesis]
• Jacobsen G., Schaumburg I., Sigsgaard T., Schlünssen V. [2010]: Non-malignant respiratory diseases and occupational exposure to wood dust. Part II. Dry wood industry. Annals of Agricultural and Environmental Medicine 17 [1]: 29–44
• Kopecký Z., Rousek M. [2012]: Impact of dominant vibrations on noise level of dimension circular sawblades. Wood Research 57 [1]: 151–160
• MaScontrol [2009] Milling and Sizing Control Software for Laser Particle Sizers and Mills from Fritsch GmbH Manual. Fritsch GmbH. Idar-Oberstein. Gremany. [User manual]
• Očkajová A., Beljaková A., Siklienka M. [2010]: Morphology of dust particles from the sanding process of the chosen tree species. Wood Research 55 [2]: 89–98
• Orłowski K. [2007]: Experimental studies on specific cutting resistance while cutting with narrow-kerf saws. Advances in Manufacturing Science and Technology 31 [1]: 49–63
• Orłowski K. [2010]: The fundamentals of narrow-kerf sawing: the mechanics and quality of cutting. Publishing house of the Technical University in Zvolen. Zvolen
• Pařil P, Brabec M, Maňák O, Rousek R, Rademacher P, Čermák P, Dejmal A [2014]: Comparison of Selected Physical and Mechanical Properties of Densified Beech Wood plasticized by ammonia and saturated steam. European Journal of Wood and Wood Products 72 [5]: 583–591
• Rogoziński T., Očkajova A. [2013]: Comparison of two methods for granularity determination of wood dust particles. Annals of Warsaw University of Life Sciences – Forestry and Wood Technology 81: 197–202
• Troppová E., Tippner J., Hrčka R., Halachan P. [2013]: Quasi-stationary measurements of lignamon thermal properties. BioResources 8 [4]: 6288–6296
• What is Bendywood®: www.bendywood.info [accessed 15.6.2014]
• List of standards
• ČSN ISO 9096:1998 Stacionární zdroje emisí – Stanovení hmotnostní koncentrace a hmotnostního toku tuhých částic v potrubí – Manuální gravimetrická metoda (Stationary source emissions – Determination of concentration and mass flow rate of particulate matter in gas-carrying ducts – Manual gravimetric method)

Identyfikatory

DOI

10.12841/wood.1644-3985.096.11