This study was designed to examine the feasibility of recycling cassava effluent, sawdust, and unused paper products to enhance their utilization for beneficial purpose. Waste newspaper paste (WNP), Waste writing-paper paste (WWP), and Waste carton paper paste (WCP) were prepared and then used separately to similarly fabricate composite panels with Sawdust particle (SDP) proportioned at 0%, 25%, 50%, 75%, and 100% by weight. The binder used was cassava starch slurry prepared from the effluent. Bulk density, water absorption, thermal conductivity, specific heat capacity, thermal diffusivity, nailability, and flexural strength were determined for the developed samples. From the results obtained, the samples were found to be light-weight and their thermal insulation performance improved with increasing proportions of the SDP. Though samples containing the WCP exhibited the best satisfactory performance, it was found that all the studied samples could perform more effectively and efficiently as ceilings compared to some of those reported in the literature. From scientific-economic viewpoint, valorizing the above-mentioned wastes as described in this paper could help to protect the environment and also yield value-added insulation ceilings for enhancement of sustainable building construction especially in tropical areas.
PL
Celem pracy było określenie możliwości recyklingu ścieków z manioku, trocin i odpadowych materiałów papierniczych w celu ich szerszego wykorzystania. Nitki z makulatury gazetowej (WNP), nitki z makulatury z papieru do pisania (WWP) i nitki z makulatury z kartonu (WCP) zostały przygotowane, a następnie użyte osobno do wytworzenia paneli kompozytowych z dodatkiem trocin (SDP) przy udziale masowym 0%, 25%, 50 %, 75% i 100%. Zastosowanym spoiwem była przygotowana z odcieku zawiesina skrobi z manioku. Dla przygotowanych próbek określono gęstość nasypową, nasiąkliwość, przewodność cieplną, ciepło właściwe, dyfuzyjność cieplną, zdolność do wbijania gwoździ i wytrzymałość na zginanie. Na podstawie uzyskanych wyników stwierdzono, że próbki miały małą gęstość objętościową, a ich właściwości termoizolacyjne poprawiały się wraz ze wzrostem udziału trocin (SDP). Chociaż próbki zawierające WCP wykazywały najlepsze właściwości, stwierdzono, że z wszystkich badanych próbek można wytworzyć sufity o lepszych właściwościach w porównaniu z podobnymi opisanymi w literaturze. Z naukowo-ekonomicznego punktu widzenia zastosowanie wyżej wymienionych odpadów, jak opisano w tym artykule, może pomóc w ochronie środowiska, a także w uzyskaniu bardziej ciepłochronnych stropów, a co za tym idzie przyczyni się do rozwoju bardziej zrównoważonego budownictwa, zwłaszcza w obszarach tropikalnych.
Artykuł przedstawia wstępne wyniki badań wytrzymałości na zginanie oraz ściskanie innowacyjnych materiałów geopolimerowych. Geopolimery zostały wykonane według dwóch receptur. Pierwszy produkt był próbą kontrolną (odniesienia), a drugi - próbą modyfikowaną (docelową). Przedstawione zostały również wyniki badań gęstości otrzymanych materiałów budowlanych. Wykazano możliwości zastąpienia czystych chemicznie substratów w procesie geopolimeryzacji materiałami odpadowymi.
EN
The article presents the preliminary results of bending and compressive strength tests of innovative geopolymer materials. Geopolymers were made according to two recipes. The first product was the control (reference) sample and the second was the modified (target) sample. The results of density tests of the obtained building materials were also presented. The possibilities of replacing chemically pure substrates in the geopolymerization process with waste materials have been demonstrated.
Celem eksperymentu była ocena wpływu temperatury utwardzania na wybrane właściwości użytkowe wyrobów do łączeń konstrukcyjnych. Do badań wytypowano trzy kleje epoksydowe przeznaczone - w ramach naprawy konstrukcji betonowych - do przyklejania materiałów, takich jak np. maty z włókien węglowych, szklanych i aramidowych. Substraty, z których składają się poszczególne kleje, jak również przygotowane obiekty badawcze, kondycjonowano w warunkach laboratoryjnych oraz ekstremalnych temperaturach utwardzania, wytypowanych do projektu w oparciu o informacje znajdujących się w kartach technicznych wyrobów. Jako temperatury ekstremalne przyjęto maksymalną 35˚C i minimalną 10˚C wartość deklarowaną wspólną dla wytypowanych klejów. Przeprowadzono badania, których wyniki stanowią podstawowe kryterium oceny jakości połączeń klejowych, takie jak: wytrzymałość na ścinanie (przy różnych wartościach kąta nachylenia złącza), wytrzymałość na ściskanie i zginanie. Dodatkowo wykonano badanie przyczepności betonu starego do betonu starego, które pozwoliło określić, jaki wpływ ma temperatura utwardzania na połączenie kleju i betonu. Analiza uzyskanych wyników wykazała wpływ temperatury utwardzania wyrobów do łączeń konstrukcyjnych na ich wybrane właściwości użytkowe. Większy wpływ na obniżenie poziomu uzyskanych parametrów ma spadek temperatury utwardzania klejów do łączenia konstrukcyjnego do 10°C.
EN
The aim of the experiment was to evaluate the influence of the hardening temperature on selected performance properties of products for construction joints. Three epoxy adhesives were selected for the tests, intended - as part of the repair of concrete structures - for gluing materials such as carbon, glass and aramid fiber mats. The substrates, which make up the individual adhesives, as well as the prepared research objects, were conditioned in laboratory conditions and extreme hardening temperatures, selected for the project based on the information contained in the technical data sheets of the products. The maximum 35˚C and minimum 10˚C declared values shared by the selected adhesives were adopted as extreme temperatures. Tests were carried out, the results of which constitute the basic criterion for assessing the quality of adhesive joints, such as: shear strength (at different values of the angle of inclination of the joint), compressive and bending strength. In addition, the adhesion test of the old concrete to the old concrete was performed, which allowed to determine the influence of the hardening temperature on the bonding of the adhesive and concrete. The analysis of the obtained results showed the influence of the hardening temperature of products for construction joints on their selected performance properties. The decrease in the curing temperature of structural adhesives to 10°C has a greater impact on the reduction of the obtained parameters.
Zbadano wpływu parametrów wytwarzania, tzn. infiltracji miedzią, na mikrostrukturę i właściwości mechaniczne kół zębatych wytworzonych techniką metalurgii proszków na bazie proszku żelaza Distaloy AQ. Zakres badań obejmował określenie zmiany wymiarów kół oraz ich gęstości, przed i po procesie infiltracji, pomiar wytrzymałości na statyczne zginanie zębów, pomiar mikrotwardości kół zębatych oraz analizę ich mikrostruktury. Koła zębate podzielono na cztery grupy; jedna z nich nie była infiltrowana miedzią, pozostałe trzy infiltrowano kolejno jednym (1,4% Cu), dwoma (2,8% Cu) i trzema (4,2% Cu) miedzianymi pierścieniami. Stwierdzono, że infiltracja miedzią powoduje wzrost wytrzymałości na zginanie badanych spieków, lecz tylko w przypadku zawartości 1,4% Cu. Większa ilość miedzi powoduje obniżenie wytrzymałości na zginanie zębów kół. Badania wykazały również, że infiltracja miedzią nie wpływa korzystnie na mikrotwardość kół zębatych.
EN
The influence of production parameters i.e., copper infiltration, on the microstructure and mechanical properties of gear wheels initially manufactured by powder metallurgy was investigated. Distaloy AQ iron powder was used for production these gears. The scope of research included the determination of changes in the dimensions of the gear wheels and their density, before and after the infiltration process, measurement of the strength to static bending, measurement of the microhardness of the gear wheels and analysis of their microstructure. The gear wheels are divided into four groups; one of them was not infiltrated with copper, the remaining three were infiltrated successively with one (1.4% Cu), two (2.8% Cu) and three (4.2% Cu) copper rings. It was found that copper infiltration increases the bending strength of the tested sinters, but only in the case of 1.4% Cu content. The greater amount of copper reduces the bending strength of the gear wheels. Research has also shown that copper infiltration does not have a positive effect on the microhardness of gear wheels.
5
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
Ethiopia has abundant invasive aquatic plants like water hyacinth and water lily. Large masses of these invasive plants have a negative impact on the country’s water bodies, specifically at Lake Tana in Ethiopia, by infesting and deteriorating water quality and reducing the quantity of water. In this research work, an attempt was made to fabricate a natural fiber reinforced composite in which water lily fiber was used as the reinforcing material in a polyester resin matrix. Chopped water lily fiber reinforced polyester resin composites were prepared by varying the fiber content - 20, 40 and 60 wt.%. Mechanical properties such as tensile strength and flexural strength were tested as per ASTM standards to evaluate the influence of the fiber contents. The experimental results show that an increase in the fiber content enhanced the mechanical properties of the water lily fiber reinforced polyester composite. It was found that the composite with 40 wt.% fiber exhibited superior strength which could be suitably used for different applications.
6
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
Beton, czyli główny materiał sektora budowlanego, był przedmiotem wielu badań naukowych przez dziesięciolecia. W wyniku tych badań uzyskano nowe informacje naukowe na temat słabych punktów materiałów cementowych, szczególnie betonu, ich zachowania pod obciążeniem itp. W świetle tych informacji zaleca się, aby niektóre metody badawcze określone w normach międzynarodowych zostały zrewidowane. W niniejszym badaniu zbadano wpływ uszkodzeń spowodowanych przez badanie wytrzymałości na zginanie przeprowadzane na próbkach przygotowanych z beleczek z zaprawy o wymiarach 160 mm x 40 mm x 40 mm w ramach norm EN 13813, EN 13888, EN 13279-1, EN 197-1, TS 13566 i TS 13687, na wyniki badania wytrzymałości na ściskanie przeprowadzonego na złamanych próbkach. W końcowej analizie zaproponowano pewne sugestie dotyczące ulepszenia metody badawczej.
EN
Concrete, the principal material of the construction sector, has been the subject of many scientific researches for decades. As a result of these investigations, new scientific information has been obtained on the weak points of cement-based products, especially concrete, their behaviour under load, etc. In light of this information, it is recommended that some test methods specified in international standards be revised. In this study, the effect of damage caused by flexural strength test performed on samples prepared with mortar prisms, of dimensions 160 mm x 40 mm x 40 mm within the scope of EN 13813, EN 13888, EN 13279-1, EN 197-1, TS 13566 and TS 13687 standards, on the results of compressive strength test performed on the broken samples was investigated. In the final analysis, some improvement suggestions have been made in the test methods in question.
The heat-cured core-making process has been applied for over 60 years to produce molds and cores for different types of castings. The following technologies can be classified into the terminology of “heat-cured coremaking process”: croning-, hot-box -, and warm-box process. The latest technology provides good workability of core mixture, good strength properties, dimensional stability, and good knockout performance of the sand cores. Despite all its advantages, the warm-box technology is less widespread in foundries due to the cost of the high quality thermosetting resin and the maintenance cost of the core box. In this study, the influence of the acid hardener content on the hardening characteristics (bending strength), collapsibility, and the benchlife of the warm-box sand cores were investigated. From the results, it can be said, that within the investigated composition range, increasing the acid hardener content will improve the bending strength of the sand cores. The increased acid hardener content results in higher thermal stability at the beginning of the thermal exposure, and smaller residual bending strength after 15 minutes of thermal loading. The acid hardener level has little effect on the benchlife of the warm-box sand cores, although the sand core mixture is very sensitive to the combined effect of the sand temperature and dwelling time.
The application of used glazed waste in concrete production can improve the performance of the structure of the building. Flexural and shear behavior and action of reinforced Hollow Glass Concrete Beams (HGCB) and Solid Glass Concrete Beams (SGCB) made with glass waste under a two-point load are studied in this paper. In this work, 6 reinforced concrete solid and hollow beams were tested under a four-point bending test to evaluate and calculate the flexural behavior of SGCB and HGCB. For that purpose, Beams were prepared with 1000 mm length, 230 mm height, and 120 mm. All beams were divided into groups and named according to the space stirrups steel bar. The experimental work investigates five main variables which are: first: the comparison between SGCB and HGCB with the concrete beams made with glass waste (Glass Concrete Beam GCB), second: comparison between Solid Concrete Beams for Normal Concrete Beams (NCB), and GCB, three: comparison between Hollow Concrete Beams for NCB and GCB, four: the comparison between HGCB and HCB, last: the comparison between SGCB and SCB. The test results indicated that GCB was offered higher strength than NCB, but the load-slip behavior of all specimens is similar for both types of concretes, and the bond strength is not influenced by steel specimens. Furthermore, the results of this study indicated that the contribution of GCB to the load is indicated to be considerable. The results indicate that the hollow opening affected the ultimate load capacity and deflection of HGCB.
The experimental tests presented in this work concern the impact resistance test and residual strength properties after an impact performed by a drop tower INSTRON CEAST 9340. The authors prepared samples of a composite material with a polymeric matrix L285 and H285 hardener, reinforced with eight ply fabric of carbon fibre. Two shapes of the impactor (spherical and V-shape) were used to perform the testing. The samples were impacted by three values of energy (10, 15, 20 [J]). Three-point bending tests were performed to the residual strength of the samples subjected to impact tests and compared to samples which had not been damaged earlier. The study showed differences in the influence of the shapes of the impactor on the nature of the composite damage. After the test, conclusions were drawn about the influence of the shape of the impactor on the area of composite damage and its character. Also, its influence on residual strength was described. Despite the clear differences in the area of damage to composites impacted by different impactors, this does not have a significant influence on the residual strength.
PL
Przedstawione w pracy badania eksperymentalne dotyczą badania udarności oraz właściwości wytrzymałości szczątkowej po uderzeniu wieżą zrzutową INSTRON CEAST 9340. Autorzy przygotowali próbki materiału kompozytowego z osnową polimerową L285 i utwardzaczem H285, wzmocnionego tkaniną ośmiowarstwową z włókna węglowego. Do badań wykorzystano dwa kształty impaktora (kulisty i V). Próbki były poddawane działaniu trzech wartości energii (10, 15, 20 [J]). Próby zginania trzypunktowego przeprowadzono do wytrzymałości szczątkowej próbek poddanych próbom udarności i porównano z próbkami, które wcześniej nie uległy uszkodzeniu. Badania wykazały różnice we wpływie kształtów impaktora na charakter uszkodzenia kompozytu. Po przeprowadzeniu badań wyciągnięto wnioski dotyczące wpływu kształtu impaktora na obszar uszkodzenia kompozytu i jego charakter. Opisano również jego wpływ na wytrzymałość resztkową. Pomimo wyraźnych różnic w obszarze uszkodzeń kompozytów pod wpływem różnych impaktorów, nie ma to istotnego wpływu na wytrzymałość szczątkową.
The article presents the results of the assessment of the possibility of using chalcedonite powder as a partial replacement for cement in mortars. Portland cement CEM I 42.5 R was used as a binder, which was replaced in the amount of 5%, 20%, 35% and 50% with chalcedonite powder. The experimental tests concerned the determination of the technological and mechanical properties of mortars: consistency, air content, compressive and bending strength, supplemented by X-ray diffraction analysis and calorimetric measurements of the pastes. The research results indicate that chalcedonite powder can be used in the production of mortars. The best mechanical properties of tested mortars were obtained in the case of replacing cement with the addition of powder in the amount of 5% and 20%.
PL
W artykule dokonano oceny możliwości wykorzystania mączki chalcedonitowej jako częściowego zamiennika cementu w zaprawach budowlanych. Jako spoiwo zastosowano cement portlandzki CEM I 42,5 R, który zastępowano w ilości 5%, 20%, 35% oraz 50% mączką chalcedonitową. Badania doświadczalne dotyczyły określenia właściwości technologicznych i mechanicznych zapraw: konsystencji, zawartości powietrza, wytrzymałości na ściskanie i zginanie, uzupełnionych o rentgenowską analizę dyfrakcyjną oraz badania kalorymetryczne zaczynów. Wyniki badań wskazują, że mączka chalcedonitowa może być stosowana do produkcji zapraw budowlanych. Najlepsze właściwości mechaniczne badanych zapraw uzyskano w przypadku zastąpienia cementu dodatkiem mączki w ilości 5% i 20%.
12
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
Podczas eksploatacji elewacji wentylowanych z okładzinami z płyt włóknisto-cementowych często uwidoczniają się zmiany w postaci przebarwień i w wielu przypadkach towarzyszą im deformacje okładzin. Czy zmiany te mają charakter wyłącznie estetyczny i czy wpływają na właściwości użytkowe systemu elewacyjnego? Przeprowadzone badania laboratoryjne dają podstawy do stwierdzenia, że wraz ze zmianami wizualnymi zachodzą zmiany strukturalne oraz wytrzymałościowe w okładzinach, które mogą mieć istotny wpływ na właściwości techniczno-użytkowe systemów elewacyjnych, w tym bezpieczeństwa użytkowania.
EN
During the exploitation on fiber-cement cladings of ventilated facades systems sometimes are visible changes in the form of discoloration. Discoloration is often accompanied by deformation of the cladding. Are these changes aesthetic and do they also have an impact on the performance properties of the façade system? The laboratory tests give grounds to state that along with the visual changes, structural and strength changes in the claddings occur which changes may have a significant impact on the technical and operational properties of facade systems, including the safety of use.
13
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
W artykule przedstawiono wyniki badań wpływu włókien odpadowych z branży garbarskiej i tekstylnej na wytrzymałość na zginanie zapraw cementowych i gipsowych w aspekcie wykorzystania ich do produkcji płyt okładzinowych. Badania przeprowadzono na próbkach zapraw zawierających spoiwo cementowe i gipsowe o wymiarach 12 x 75 x 150 mm. Większy wpływ na poprawę właściwości wytrzymałościowych miały włókna odpadowe w kompozytach zawierających cement. Stwierdzono, że pomimo znacznego zróżnicowania włókien ich dodatek poprawił wytrzymałość na zginanie, co uzasadnia ich zastosowanie w produkcji materiałów stosowanych w budownictwie.
EN
The article presents the results of research on the influence of waste fibers from the tanning and textile industries on the flexural strength of cement and gypsum mortars in terms of their use for the production of facade boards. The tests were carried out on samples of mortars containing cement and gypsum with dimensions of 12 x 75 x 150 mm. Waste fibers in cement-containing composites had a greater impact on the improvement of strength properties. It was found that despite the significant diversification of fibers, their addition improved the flexural strength, which justifies their use in the production of building materials.
14
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
W artykule przedstawiono zależności korelacyjne pomiędzy cechami mechanicznymi a wynikami badań sklerometrycznych krajowego drewna sosnowego. Siła uzyskanych korelacji była zróżnicowana. Najsilniejszą korelację do wyników badań sklerometrycznych uzyskano w przypadku gęstości drewna, a w dalszej kolejności do wytrzymałości na zginanie i ściskanie. Dodatkowo zaprezentowano funkcje korelacyjne sprowadzone do wartości kwantylowej, mogące stanowić podstawę do oceny cech fizykomechanicznych drewna w istniejących konstrukcjach, przede wszystkim zabytkowych.
EN
The paper presents correlations between mechanical properties for domestic pine wood and the results of sclerometric tests. The correlation power varied, the strongest correlation to the results of sclerometric tests was obtained for wood density, followed by flexural and compressive strength. In addition, the paper presents correlation functions reduced to a quantile value, which can provide a basis for evaluating the physical and mechanical properties of timber in existing structures, in particular historic ones.
Purpose: This paper aims to prepare depolymerized polyethylene terephthalate (DPET) powder from recycled plastic water bottles. Adding this DPET powder to the cement mortar was also studied. Design/methodology/approach: The adopted PET depolymerization process includes the usage of both ethylene glycol (EG) as solvent and nano-MgO as a catalyst. A bubble column reactor was designed for this process. Five different mortar groups were made; each has different DPET content of 0%, 1%, 3%, 6% and 9% as a sand replacement. The flexural strength testand the water absorption measurement are done after two curing periods: 7 and 28 days. Findings: The research finding demonstrated that the flexural strength of mortar was reduced by increasing the DPET powder percentage and the maximum dropping was 15% when 9% of DPET was added. The ability of the mortar to absorb the water was reduced by 14.5% when DPET powder was 9%. The mortar microstructure is featured with fewer cavities and porosity. Research limitations/implications: This work’s employed bubble column technique is limited only to the laboratory environment and needs to be scaled up within industrial mass production. For future research, it is suggested to decrease depolymerization time by using smaller pieces of plastic water bottle waste and trying other types of nanocatalyst. Practical implications: The modified mortar can be utilized in areas where moisture, rainfalls, and sanitation systems exist. Originality/value: The article claims that depolymerized waste PET improves chemical process efficiency by lowering reaction time and improving mass and heat transfer rates. Besides, this approach saves money. It is found out that the depolymerized plastic waste is much more functional due to its high cohesion capability than being used as small PET pieces.
W pracy przedstawiono różnego rodzaju podejście do kwestii modyfikacji żywic poliestrowych przy użyciu nanododatków. Poruszono zagadnienia nasiąkliwości kompozytów na bazie żywic, ich ognioodporności, a także udarności i wytrzymałości na zginanie. Zwrócono szczególną uwagę na metody z którymi wiąże się najbardziej korzystne rokowania.
EN
The paper presents a different approach to the modification of polyester resins with the use of nano-additives. The issues of absorbability of resinbased composites, their fire resistance, as well as impact strength and flexural strength were discussed. Particular attention was paid to the methods with the most favorable prognosis.
W pracy zaprezentowano wpływ procentowego zastąpienia piasku kwarcowego cenosferami na wybrane właściwości zapraw cementowych. Stopniowano ilość dodatku cenosfer co 20% całkowitej objętości kruszywa, zaczynając od zaprawy referencyjnej bez wypełniacza, po zaprawę wykonaną wyłącznie na bazie cenosfer. Oceniano takie parametry, jak gęstość, współczynnik przewodzenia ciepła i wytrzymałość na zginanie i ściskanie.
EN
The paper presents the effect of the percentage replacement of quartz sand with cenospheres on selected properties of cement mortars. The amount of cenospheres addition was graded every 20% of the total aggregate volume, starting from the reference mortar without filler, to mortar made solely on the basis of cenospheres. Parameters such as density, thermal conductivity as well as bending and compressive strength were assessed.
18
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
The presence of particles and fibers as reinforcement in a polymer matrix greatly enhances the mechanical properties. Agricultural residues and natural fibers are commonly used nowadays due to the fact that they easily decompose even after a longer period and they are eco-friendly in nature. f Fiber that was extracted from stem of Calotropis gigantea was selected as reinforcement in the present investigation. Initially the fiber was treated with a sodium hydroxide solution and CG fiber-epoxy composites were prepared. The properties of alkaline treated CG fiber-reinforced epoxy composites were further improved by the addition of particles such as chitosan, red mud and rice husk. Properties such as the tensile strength, flexural strength, impact toughness, hardness, water absorption, thickness swelling behaviour, specific wear rate and coefficient of friction were evaluated and compared. The XRD pattern of the chemically treated CG fiber-reinforced parrticle-filled epoxy composites was presented in the present study.
Purpose: The mechanical characteristics of concrete used in rigid pavements can be improved by using fibre-reinforced concrete. The purpose of the study was to predict the flexural strength of the fibre-reinforced concrete for ten input variables i.e., cement, fine aggregate, coarse aggregate, water, superplasticizer/high range water reducer, glass fibre, polypropylene fibre, steel fibres, length and diameter of fibre and further to perform the sensitivity analysis to determine the most sensitive input variable which affects the flexural strength of the said fibre-reinforced concrete. Design/methodology/approach: The data used in the study was acquired from the published literature to create the soft computing modes. Four soft computing techniques i.e., Artificial neural networks (ANN), Random forests (RF), Random trees RT), and M5P, were applied to predict the flexural strength of fibre-reinforced concrete for rigid pavement using ten significant input variables as stated in the ‘purpose’. The most performing algorithm was determined after evaluating the applied models on the threshold of five statistical indices, i.e., the coefficient of correlation, mean absolute error, root mean square error, relative absolute error, and root relative squared error. The sensitivity analysis for most sensitive input variable was performed with out-performing model, i.e., ANN. Findings: The testing stage findings show that the Artificial neural networks model outperformed other applicable models, having the highest coefficient of correlation (0.9408), the lowest mean absolute error (0.8292), and the lowest root mean squared error (1.1285). Furthermore, the sensitivity analysis was performed using the artificial neural networks model. The results demonstrate that polypropylene fibre-reinforced concrete significantly influences the prediction of the flexural strength of fibre-reinforced concrete. Research limitations/implications: Large datasets may enhance machine learning technique performance. Originality/value: The article's novelty is that the most suitable model amongst the four applied techniques has been identified, which gives far better accuracy in predicting flexural strength.
Purpose: In building constructions, due to the decrease of local raw materials and for sustainability purpose, beside the need of light pieces to be used in roofing and false ceiling; an alkali-activated mortar is the new development where pozzolanic material is used instead of cement and activated by an alkaline solution. Therefore, in this research, alkali-activated mortar containing unexpanded clay as a fine aggregate with a dry density of 1652 kg/m3, compressive strength of 3.2 MPa, and thermal conductivity of 0.4 (W/m.K) was produced ,also boards were performed in a dimension of 305×152×12 mm as to use them in false ceiling, and reinforced with 0.25 and 0.5% steel fibre to improve their toughness by 370.8% and 1146.1% compared with reference boards, which made them good choice to used them in roofing and secondary ceiling. Design/methodology/approach: For preparation of alkali-activated mortar, low calcium fly ash (FA) was used as a source binder material. In addition, super-plasticizer and unexpanded clay as a fine aggregate (produce from the crushed artificial aggregate) in the ratio of 1:2.75 fly ash/fine aggregate. The paste was prepared by mixing fly ash with an alkali silicate solution, in a solid-to-liquid ratio of 0.4. Alkali silicate activator was prepared by mixing the NaOH and Na2SiO3 solutions at the mass ratios of 2.5. The concentrations of the NaOH was the same molarity of (14M).To improve the mechanical properties of the reference mortar mixture ,steel fibre with 0.25 and 0.5% content were added to the mix .The specimens were tested for water absorption, dry density, compressive strength, flexural strengths, flexural toughness, and thermal conductivity, in addition to the Scanning Electron Microscope test (SEM) for all mortar mixes. Alkali-activated mortar boards with (305×152×12 mm) were prepared and tested for flexural strength and toughness. Findings: The results indicated that the modulus of rupture for mortar boards reinforced with 0.25 and 0.5% steel fibre exhibits an increase of (3.68-12.10)%. In comparison, the toughness is increased by about 370.8% and 1146.1%, respectively, as compared with the reference mortar (without fibre) which made them resistance to accident, in addition to use them in roofing due to their thermal insulation. Research limitations/implications: Further research is needed to make a similar board using another sustainable material. We can examine the thermal insulation that we can get from these board, especially in the building in Iraq which the weather faces high temperatures. Practical implications: There is a by-product that we could get from the electricity station in Iraq. We must study how we get rid of it. Originality/value: This paper investigate how to produce a new light board using artificial aggregate made from unexpanded clay, which has many benefits in building insulation roofing.
JavaScript jest wyłączony w Twojej przeglądarce internetowej. Włącz go, a następnie odśwież stronę, aby móc w pełni z niej korzystać.