In the work improved system of equation of plane-parallel movement of the road train with single-axle O1-category trailer. Defined lateral reactions on the vehicle and trailer wheels at body roll, wheels slip caused by body roll and also developed road train spatial mathematical model in a transverse plane. This model is used to study the road train course stability with O1-category trailer. It is shown that the spatial model of road train with no vehicle and trailer wheels inclination has the same divergent instability characteristic as the plane road train layout.
W artykule omówiono zagadnienie wpływu OZE, którego udział w sieci elektroenergetycznej wzrasta i będzie dalej ulegał znacznemu wzrostowi w niedalekiej przyszłości. Będzie to powodowało nowe, niespotykane wcześniej w systemie elektroenergetycznym, problemy związane z szeroko rozumianą stabilnością systemu elektroenergetycznego. Zwrócono też uwagę na fakt, że rozwój energetyki rozproszonej wpływa na nowe zadania i uwarunkowania pracy układów EAZ, a operatorzy sieci przewidują decentralizację i automatyzację systemów regulacji napięcia i sankcjonowanie pracy wyspowej. Przydatnym narzędziem do analizy stanu stabilności w systemach może być pomiar PMU (Phasor Measurment Unit), coraz częściej dostępny w przekaźnikach zabezpieczeniowych jako dodatkowa funkcja. Zastosowanie synchrofazorów i techniki PMU w systemie elektroenergetycznym obejmuje już nie tylko szeroko omawianą ocenę stabilności, ale także może być przydatne w tworzeniu obszarowych - Wide Area - systemów zabezpieczeń WAP oraz systemów sterowania WACS. Oferenci, przygotowując się do zmian w systemie elektroenergetycznym, opracowują automatyki wspomagające utrzymanie stabilności w systemie. Przykładem może być firma GE, która wprowadziła na rynek produkt PowerNode, do którego nawiązano w niniejszym artykule.
EN
The article discusses the issue of the impact of Renewable Energy Sources on HV network, the share of which in the power grid is increasing and will continue to increase significantly in the near future. This will cause new problems, not previously encountered in the power system, related to the widely understood stability of the electricity system. Attention was also drawn to the fact that the development of distributed energy affects new tasks and conditions for the operation of Power Protection Automation systems, and network operators envisage decentralization and automation of voltage regulation systems and accepting of island operation of the Power System. A useful tool for analyzing the state of stability in systems may be PMU (Phasor Measurement Unit) measurement, which is more often available in protection relays as an additional function. The use of synchrophasors and PMU technology in the power system not only covers the widely discussed Power System stability assessment, but can also be useful in creating Wide Area WAP security systems and WACS control systems. In preparation for changes in the Power System, bidders are developing automation systems that help maintain stability in the system. An example is GE, which introduced the product PowerNode, which is referred to in this publication.
W pracy za pomocą zmian przewodności zbadano zmiany konformacyjne proteiny BSA oraz jej kompleksów (BSA-Au oraz BSA-NAA) pod wpływem promieniowania UV oraz MF aplikowanego frakcyjnie w dawkach (3 × 10 min oraz 6 × 10 min) oraz w sposób ciągły (30 min, 60 min). Wykonano analizę porównawczą wpływu promieniowania UV i mikrofalowego w dawkach ciągłych i frakcyjnych na BSA, BSA-Au, BSA-NAA oraz przeanalizowano czułość na pole elektromagnetyczne z zakresu UV i MF dla badanych substancji. Udowodniono efekt przyspieszonych zmian konformacyjnych pod wpływem pola elektromagnetycznego z zakresu UV i MF. Wykazano wpływ czynników na stabilność BSA i jej kompleksów zależny od: rodzaju czynnika, sposobu jego aplikacji oraz czasu ekspozycji. Najbardziej czuły na pole elektromagnetyczne okazał się kompleks BSA-Au.
EN
In this study, the conformational changes of BSA protein and its complexes (BSA-Au and BSA-NAA) under UV and MF radiation applied in fractional doses (3 × 10 min and 6 × 10 min) and continuously (30 min, 60 min) were investigated by means of conductivity changes. A comparative analysis of the effect of UV and microwave radiation in continuous and fractional doses on BSA, BSA-Au, BSA-NAA was performed, and the sensitivity to UV and MF electromagnetic fields of the tested substances was analysed. The effect of accelerated conformational changes under the influence of UV and MF electromagnetic field was proved. The influence of the factors on the stability of BSA and its complexes was shown to depend on: the type of agent, the method of its application and the exposure time. The most sensitive to the electromagnetic field turned out to be the complex BSA-Au.
This paper aims to determine the effect of global economic policy uncertainty on the banking system's stability in Asian countries. The dependent variable in the study is measured through the bank's payment risk Zscore. The primary explanatory factor is global economic policy uncertainty, and other control variables include the banking system's characteristics and the national economic environment. Asian banking systems’ data are collected from World Bank between 2008 and 2020. Based on the System Generalized Method of Moments, the main results indicate that global economic policy uncertainty is seriously exacerbating the instability of the banking system of Asian countries. The study also shows that the ability to use mobilized capital and the degree of concentration of the system reduces the adverse impact of global economic policy uncertainty on the stability of the banking system in Asian countries.
PL
Celem niniejszego artykułu jest określenie wpływu niepewności globalnej polityki gospodarczej na stabilność systemu bankowego w krajach azjatyckich. Zmienna zależna w badaniu jest mierzona za pomocą wskaźnika Zscore ryzyka płatniczego banku. Głównym czynnikiem objaśniającym jest niepewność globalnej polityki gospodarczej, a inne zmienne kontrolne obejmują charakterystykę systemu bankowego i krajowe środowisko gospodarcze. Dane dotyczące azjatyckich systemów bankowych pochodzą z Banku Światowego w latach 2008-2020. W oparciu o system uogólnionej metody momentów, główne wyniki wskazują, że niepewność globalnej polityki gospodarczej poważnie pogarsza niestabilność systemu bankowego krajów azjatyckich. Badanie pokazuje również, że zdolność do wykorzystania zmobilizowanego kapitału i stopień koncentracji systemu zmniejsza niekorzystny wpływ niepewności globalnej polityki gospodarczej na stabilność systemu bankowego w krajach azjatyckich.
Kryvyi Rih iron ore basin consists of complex structured ore deposits and is developed by the underground method at depths of over 1000 m. The underground method is used to mine reserves of rich iron ores with a useful component content of more than 59% applying bulk ore and rock caving systems. This leads to significant changes in the stress state of the rock massif. During underground operations, mine workings are strained and in some cases destructed. As a result, enterprises are constantly increasing operating costs for maintaining mine workings, which adversely impacts the cost of production. Industrial research results demonstrate that in most cases workings fail in their upper part which is vaulted in shape. Available methods for determining the state of rocks around mine workings do not fully take into account physical and mechanical properties of the rocks in which the working is located. The developed technique allows determining not only the destructive pressure impacting the workings, but also the angle at which the destructive force acts. This technique differs from the available ones in taking into account not only mining and geological characteristics of the deposit, but also most factors of physical and mechanical properties of rocks. This technique helps to choose a rational place for driving mine workings at the stage of design, thus avoiding significant additional cost for their maintenance.
PL
W kopalni Krzywy Róg występują złoża rudy o złożonej strukturze, wydobywane metodą podziemną z głębokości ponad 1000 m. Stosując systemy zawałowe eksploatuje się złoża bogatych rud żelaza o zawartości składników użytecznych powyżej 59%. Prowadzi to do znacznych zmian stanu naprężeń masywu skalnego. Podczas prac podziemnych wyrobiska kopalniane podlegają naprężęniom, a w niektórych przypadkach ulegają zniszczeniu. W efekcie przedsiębiorstwa stale podwyższają koszty eksploatacji wyrobisk górniczych, co niekorzystnie wpływa na koszty produkcji. Wyniki badań przemysłowych wskazują, że w większości przypadków wyrobiska zawodzą w swojej górnej części. Dostępne metody określania stanu skał wokół wyrobisk górniczych nie uwzględniają w pełni właściwości fizycznych i mechanicznych skał, w których znajduje się wyrobisko. Opracowana technika pozwala na określenie nie tylko ciśnienia destrukcyjnego działającego na wyrobiska, ale również kąta działania siły destrukcyjnej. Technika ta rożni się od dostępnych tym, że uwzględnia nie tylko cechy górniczo-geologiczne złoża, ale także większość czynników właściwości fizykomechanicznych skał. Technika ta pozwala już na etapie projektowania na dobór racjonalnych miejsc prowadzenia wyrobisk górniczych, unikając w ten sposób znacznych dodatkowych kosztów ich utrzymania.
In underground coal mining, the stability of roadways and gob-side entry depends on the coal pillar width. An unreasonable width of the coal pillar will cause the roadway to be in a dangerous zone of influence of the abutment pressure, leading to severe roadway deformation. This paper studies the fracture mechanism of the hard main roof and reasonable coal pillar width to protect the stability of gob-side entry driving. The research results show that when mining a coal seam under a hard main roof, the console of the main roof on the edge of the coal seam has the form of hinge structure. The great load of the roof layers and the rotation of the console are the main causes leading to the variation of the stress field in the coal seam. According to the development law of the stress field, after the main roof completes the collapse process, the peak of the maximum stress will move deep into the solid coal seam, and on the edge of the coal seam it will form a low-stress zone. Research results from the case of Seam #11 of Khe Cham coal mine, Vietnam show that the gob-side entry will be well stabilized when the narrow coal pillar between it and the boundary of the gob is 4–5 m.
7
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
The influence of styrene-butadiene-styrene block copolymers (SBS polymers) on the properties of binders based on bitumen has long been the subject of wide and comprehensive studies. This paper presents an analysis of the relationship between the molecular structure of SBS polymers and their effect on the physical and mechanical properties of paving binders based on bitumen from the oil refinery in the Salavat city, the Republic of Bashkiria (territory of Russia). The amount of S B S polymers in the binder did not exceed 5% (wt.). The data obtained showed a significant relationship between the functional parameters of the binders (penetration, elasticity, storage stability) and the content, the macromolecule spatial framework and the structure of the styrene-butadiene-styrene thermoplastic elastomers used.
PL
Wpływ kopolimerów blokowych styren-butadien- styren (SBS) na właściwości lepiszczy bitumicznych jest od dawna przedmiotem szerokich badań. W artykule przedstawiono analizę zależności między topologią polimerów SBS a ich wpływem na właściwości fizyczne i mechaniczne lepiszczy drogowych uzyskanych na bazie asfaltu z rafinerii w Saławacie, zlokalizowanej na terenie autonomicznej republiki Baszkirii, wchodzącej w skład Federacji Rosyjskiej. Zawartość polimeru SBS w lepiszczu nie przekroczyła w badaniu 5% (wagowo). Uzyskane wyniki potwierdziły istotny związek między parametrami funkcjonalnymi lepiszcza (penetracją, nawrotem sprężystym, stabilnością magazynowania) a zawartością polimeru w lepiszczu, strukturą zastosowanego elastomeru termoplastycznego SBS oraz konformacją (układem przestrzennym) jego makrocząsteczek.
8
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
W pracy przedstawiono porównanie podstawowych właściwości scalonych mikroczujników warunków środowiskowych pod kątem wykorzystania ich do pomiaru temperatury otoczenia, wilgotności względnej oraz ciśnienia w laboratorium pomiarowym, w którym te trzy wielkości charakteryzują się niewielkimi przedziałami zmian. Z przeprowadzonych badań wynika, iż w stosunkowo wąskim zakresie zmian wielkości mierzonych, wyniki pomiarów uzyskiwanych za pomocą porównywanych czujników charakteryzują się bardzo dobrą zgodnością.
EN
The paper presents a comparison of the basic properties of integrated micro-sensors of environmental conditions in terms of their use to measure the ambient temperature, relative humidity and pressure in a measurement laboratory, where these three values are characterized by small change intervals. The conducted research shows that in a relatively narrow range of changes in measured values, the results of measurements obtained with the compared sensors are characterized by very good compliance.
9
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
W artykule przedstawiono metodę i układ do badania częstotliwości generatorów. Metoda ma proste podstawy teoretyczne i w praktyce pozwala łatwo i jednoznacznie ocenić dokładność i stabilność oraz zobrazować wander częstotliwości taktu zegarowego. Układ badawczy stanowi kilka najprostszych układów cyfrowych i wzmacniaczy operacyjnych, pozwalających jednak na zaawansowane pomiary napięciowe i obserwacje oscyloskopowe w czasie rzeczywistym. Ich wyniki zostały udokumentowane.
EN
The article presents a method and a system for testing the frequency of generators. The method has simple theoretical foundations and in practice allows you to easily and unequivocally assess the accuracy and stability as well as to visualize the clock frequency wander. The research system consists of several digital circuits and operational amplifiers, however, allowing for advanced voltage measurements and real-time oscilloscope observations. Their results have been documented.
10
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
In this paper, we are interested in the internal model control using neural networks in the case of linear minimum phase systems. We propose, to use the neural internal model control to solve the inversion problem of a model M(z) in order to design the IMC controller. An example application is presented and the implementation of the proposed approach is discussed.
PL
W niniejszym artykule interesuje nas sterowanie modelem wewnętrznym za pomocą sieci neuronowych w przypadku liniowych układów o minimalnej fazie. Proponujemy wykorzystanie neuronowego sterowania modelem wewnętrznym do rozwiązania problemu inwersji modelu M(z) w celu zaprojektowania sterownika IMC. Przedstawiono przykładową aplikację oraz omówiono wdrożenie proponowanego podejścia.
In this paper we present an analysis of a mathematical model of 6-P/6-TGN dynamics during the maintenance therapy of acute lymphoblastic leukemia which was proposed in Le et al. (2018). We first discuss the model with constant treatment, comparing its properties to the case without treatment. Next, we describe the model which switches between models with constant treatment and without treatment depending on frequency of drug administration and the drug’s absorption time. We show that the model with the switch has asymptotic periodic dynamics.
PL
W niniejszej pracy przedstawiono analizę modelu lekowego dynamiki 6-MP/6-TGN podczas terapii podtrzymującej ostrej białaczki limfoblastycznej, który został zaproponowany przez T. T. T. Le al. w 2018 roku. Wykazano kilka podstawowych własności, takich jak istnienie, jednoznaczność, nieujemność i ograniczoność rozwiązań. Znaleziono stany stacjonarne i zbadano ich stabilność. Dodatkowo zaprezentowano alternatywny model z przełączeniem. Wykazano, że asymptotyczne rozwiązania modelu z przełączeniem są okresowe z okresem, z jakim podawany jest lek.
W artykule przedstawiono problematykę występowania rozbieżności wskazań indeksów, określających skłonności wody do wykazywania właściwości korozyjnych, bądź do wytrącania osadu węglanu wapnia, wyznaczonych na podstawie wyników przeprowadzonych badań wody powierzchniowej. Publikacja zawiera omówienie wyników badań nad stabilnością chemiczną surowej wody z rzeki, opis metod zastosowanych do wyznaczenia indeksów stabilności wody i zasad interpretacji wartości obliczonych wskaźników, a także porównanie ich wskazania.
EN
The problem of discrepancy in the indications of indices determining the scale forming or corrosive tendencies of water were presented, based on the results of conducted research of surface water. The article presents the results of research on the chemical stability of raw river water and contains description of methods used to determine various water stability indices, as well as, interpretations of their calculated values and comparison of their indications.
Przedstawiono problematykę oceniania skłonności wody do wykazywania właściwości korozyjnych bądź do wytrącania osadu węglanu wapnia, na podstawie analizy różnych wskaźników stosowanych do wyznaczania stabilności wody, z uwzględnieniem ich metod obliczania, interpretacji oraz znanych ograniczeń w stosowaniu. W artykule opisano również praktyczne przykłady zastosowania wybranych wskaźników stabilności wody do oceny jej właściwości korozyjnych.
EN
The problems of evaluating the scale forming or corrosive tendencies of water were presented based on the analysis of various water stability indices, taking into account their calculation methods, ways of interpretation, as well as their known limitations. The article also describes practical examples of using selected water stability indices to evaluate corrosive tendencies of water.
14
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
In this study, we have proposed a mathematical model to describe the dynamics of the spread of Middle East Respiratory Syndrome disease. The model consists of six-coupled ordinary differential equations. The existence of the corona-free equilibrium and endemic equilibrium points has been proved. The threshold condition for which the disease will die out or becomes permanent has been computed. That is the corona-free equilibrium point is locally asymptotically stable whenever the reproduction number is less than unity, and it is globally asymptotically stable (GAS) whenever the reproduction number is greater than unity. Moreover, we have proved that the endemic equilibrium point is GAS whenever the reproduction number is greater than unity. The results of the model analysis have been illustrated by numerical simulations.
15
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
We establish an accurate and efficient scheme with four-order accuracy for solving three-dimensional (3D) acoustic wave equation. First, the local one-dimensional method is used to transfer the 3D wave equation into three one-dimensional wave equations. Then, a new scheme is obtained by the Padé formulas for computation of spatial second derivatives and the correction of the truncation error remainder for discretization of temporal second derivative. It is compact and can be solved directly by the Thomas algorithm. Subsequently, the Fourier analysis method and the Lax equivalence theorem are employed to prove the stability and convergence of the present scheme, which shows that it is conditionally stable and convergent, and the stability condition is superior to that of most existing numerical methods of equivalent order of accuracy in the literature. It allows us to reduce computational cost with relatively large time step lengths. Finally, numerical examples have demonstrated high accuracy, stability, and efficiency of our method.
The asymptotic stability of positive descriptor continuous-time and discrete-time linear systems is considered. New sufficient conditions for stability of positive descriptor linear systems are established. The efficiency of the new stability conditions are demonstrated on numerical examples of continuous-time and discrete-time linear systems.
Self compacting concrete (SCC) filling layer is core structure of China rail track system (CRTS) ? type ballastless track. Construction quality, service performance and durability of CRTS ? ballastless structure are affected by stability of SCC for filling layer. In this study, the stability of SCC of filling layer is researched at three levels as paste, mortar and concrete by theory and experiment. Evaluation indices including bleeding (B), surface bubble rate (θ), thickness of paste (𝜎paste) and thickness of surface mortar (L) are proposed based on the theoretical calculation and analysis. The threshold viscosity of paste 0.394 Pa·s and mixture satisfied area are obtained at paste level based on the relationship between viscosity and B, θ of paste. The mixture satisfied area was defined at mortar level under criterions of maximum value of 𝜎paste and slump flow. Optimal range of gap between neighboring aggregates (λca) 12.4 mm-14.1 mm is chosen by flow ability, passing ability, stable ability of SCC. These research results will help to further understand the stability of SCC.
The work concerns potential applications of stilbene derivatives as preservatives. The structure of stilbene molecule has been known since 1829. One of the most known stilbene derivatives is resveratrol. Many of derivatives synthesized so far show antimicrobial, estrogenic, antitumor and other effects. Stilbene derivatives discussed in this study show activity against 9 different microorganisms, i.e. Staphylococcus aureus 209P FDA, Streptococcus faecalis ATCC 8040, Bacillus subtilis ATCC 1633, Escherichia coli PZHO 26B6, Klebsiella pneumoniae 231, Pseudomonas aeruginosa 5 Rl, Candida albicanus PCM 1409 PZH, Microsporum gypseum K1, Aspergillus fumigates Cl. The following derivatives were tested: chloride of (E)-N-(o-nitrobenzyl)-2- hydroxystilbazole-4, bromide of (E)-N-(p-bromobenzyl)-4’-hydroxystilbazole-4, bromide of (E)-N-(m-bromobenzyl)-4'-hydroxystilbazole-4, chloride of (E)-N-(p- nitrobenzyl)-4'-hydroxystilbazole-4, bromide of (E)-N-(o-bromobenzyl)-2- hydroxystilbazole-4, chloride of (E)-N-(p-chlorobenzyl)-4’-hydroxystilbazole-4. In order to determine of short- and long-term stability of six stilbene derivatives mentioned, tests were carried out using three matrices, i.e. surface water, wastewater and distilled water. Due to possible changes in time, the content of the analyzed derivatives was determined as standard in four time intervals, i.e. after 1 hour, 7 days, 28 days and 12 months. In the research, the isotachophoresis technique was used. The lowest concentrations of the analyzed derivatives were found in wastewater.
The article presents the results of study on interaction between the liquid NiBSi alloy and solid, thin, micrometer-range layers of transition metal carbides of IVB - VIB groups of the periodic table. The reactive magnetron sputtering method was adopted to deposit of these layers on molybdenum substrates. Carbide layers are destroyed in contact with liquid alloy by dissolving, intensified by the penetration of the liquid along the coating ‒ substrate interface. The strong interaction between liquid NiBSi and both the carbide ceramics and the refractory metal substrate was revealed. The effect intensity differs somewhat for both tested carbide groups: VIB (relatively fast) and IVB (less intense).
PL
W artykule przedstawiono wyniki badań oddziaływania ciekłego stopu NiBSi z litymi, cienkimi, mikrometrowymi warstwami węglików metali przejściowych IVB – VIB grup układu okresowego pierwiastków. Do nanoszenia tych warstw na podłożach molibdenowych adoptowano metodę reaktywnego rozpylania magnetronowego. Warstwy węglików ulegają destrukcji w trakcie kontaktu z ciekłym stopem poprzez ich rozpuszczanie, intensyfikowane penetracją cieczy po granicy powłoka - podłoże. Świadczy to o silnym oddziaływaniu cieczy NiBSi zarówno z ceramiką węglikową, jak i podłożem z metalu trudnotopliwego. Efekt ten jest zróżnicowany dla węglików metali grup VIB (stosunkowo szybki) i IVB (mniej intensywny).
The problem of fall is still unsolved even though it is a serious problem, especially in group of elderly. Also, another difficulty is to analyse falls that occur in day-to-day life. Those events are hard to observe by specialists and so it is hard to analyse them. Following work contains a description of experimental process for external force-caused fall observation with the use of motion capture system and dynamometric platforms. Data collected according to this protocol were later used for time series neural networks. Obtained results of analysis were compared to popular model of human stability. Conducted inquiry proves that it is possible to detect fall even before it occurs and while it is external force-caused fall the loss of stability develops earlier than it was assumed.
JavaScript jest wyłączony w Twojej przeglądarce internetowej. Włącz go, a następnie odśwież stronę, aby móc w pełni z niej korzystać.