W artykule zwrócono uwagę na możliwość wykonania efektywnego wzmocnienia stalowych belek dwuteowych z wykorzystaniem przewiązek skrajnych. Przedstawiono analizy parametryczne, z których wynika, że wzmocnienie elementów może sięgać kilkudziesięciu procent. Zależy to jednak od wielu czynników, jak np. długość czy przekrój poprzeczny wzmacnianych belek, wymiary zastosowanych blach wzmacniających czy ich lokalizacja na długości belki. Jest to sposób nieujęty w obowiązujących normach do projektowania konstrukcji, lecz w niektórych przypadkach może się okazać wyjątkowo efektywną metodą wzmocnienia konstrukcji.
EN
The paper highlights the possibility of performing effective strengthening of steel I-beams using batten plates. Parametric analyses are presented which show that the strengthening of the members can reach several tens of percent. However, this depends on many factors, such as the length or cross-section of the beams to be strengthened, the dimensions of the reinforcing plates used and their location along the length of the beam. This is a method not included in current standards for structural design, but in some cases it can prove to be an extremely effective method of structural strengthening.
Artykuł zawiera inżynierski przykład obliczeniowy, w którym porównano nośności obciążonych osiowo i mimośrodowo słupów o przekroju kołowym i średnicy 320 mm i różnych długościach 3,0, 4,5 i 6,0 m. Słupy obliczano wariantowo jako betonowe, żelbetowe, stalowe rurowe oraz zespolone w postaci: rury stalowej wypełnionej betonem zbrojonym oraz rury stalowej wypełnionej betonem ze zbrojeniem sztywnym z dwuteownika. Obliczając słup zespolony obciążony mimośrodowo, wyprowadzono wyrażenie pozwalające ustalić parametry krzywych interakcji moment - siła osiowa, bowiem w literaturze dostępne są odnośne wzory jedynie dla słupów o przekroju prostokątnym.
EN
In the paper the computational example of the bearing capacity of circular columns is presented. The columns of 320 mm in diameter and different length 3,0 m, 4,5 m and 6,0 m are considered. Concrete and reinforced concrete columns, steel tubes and composite columns (steel tube with reinforced concrete inside and steel tube filled with concrete and double-T-bar inside) were calculated and compared. Leading calculations of composite column loaded with eccentricity, the expression was derived allowing the calculation of the parameters of the moment - axial force interaction curves, because in the literature the relevant expressions are available only for rectangular cross-section.
Zmieniające się warunki użytkowania istniejących elementów konstrukcji determinują konieczność wykonania powtórnej weryfikacji nośności. Zadanie takie może komplikować się w świetle wielu zmiennych, które należy uwzględnić podczas analizy ustrojów. W artykule przywołano dwa przypadki obiektów już eksploatowanych, na dachach których planowano zamocować panele fotowoltaiczne. Ocena możliwości dodatkowego ich dociążenia poprzedzona została sporządzeniem projektów branżowych, zawierających m.in. lokalizację (rozkład) paneli, jak również ich ciężar. W artykule ten problem opisano jako studium przypadku dla dwóch niezależnych dachów, wykonanych w różniących się technologiach.
EN
The changing conditions of use of existing structure elements determine the need to re-verify the load-bearing capacity. Such a task may become more complicated in light of the many variables that must be taken into account when analyzing systems. The article mentions two cases of facilities already in operation, on the roofs of which photovoltaic panels were planned to be installed. The assessment of the possibility of additional load was preceded by the preparation of industry projects, including, among others: location (distribution) of panels as well as their weight. The article describes this problem as a case study for two independent roofs made using different technologies.
W artykule zaproponowano wartości obciążeń i oddziaływań, które jako pochodne pionowego obciążenia eksploatacyjnego mogłyby być stosowane w odniesieniu do istniejących mostów i wiaduktów kolejowych, przede wszystkim zabytkowych. Zaproponowano również wartości oddziaływań, które są niezależne od pionowego obciążenia, a powinny być brane pod uwagę przy sprawdzaniu bezpiecznego użytkowania istniejących obiektów kolejowych. Zaproponowano wartości współczynników obliczeniowych w odniesieniu do poszczególnych obciążeń i oddziaływań. Podstawę techniczną zaproponowanych zasad stanowi przyjęcie obciążenia pionowego według normy PN-EN 15528 i pozostałych wymagań według normatywów niemieckich dotyczących istniejących kolejowych konstrukcji mostowych. Artykuł dotyczy zasad sprawdzania bezpieczeństwa kolejowych mostów i wiaduktów mających charakter obiektów zabytkowych, a takich obiektów w Polsce jest ponad 900. Niestety coraz częściej są zastępowane obiektami nowymi, choć mogą być w dalszym ciągu użytkowane.
EN
The article proposes the values of loads and actions which, as derivatives of the vertical service load, could be applied to the existing bridges and railway viaducts, especially the historic ones. Action values that are independent of the vertical load have also been proposed, and should be taken into account when checking the safe use of existing railway facilities. Values of calculation coefficients were proposed in relation to individual loads and impacts. The technical basis for the proposed rules is the adoption of the vertical load according to the PN-EN 15528 standard and other requirements according to German standards for existing railway bridge structures. The article concerns the rules for checking the safety of railway bridges and viaducts that are historic buildings, and there are over 900 such buildings in Poland. Unfortunately, they are increasingly being replaced with new ones, although they can still be used.
W artykule przedstawiono wyniki wybranych badań laboratoryjnych certyfikowanych modułów do wykonywania budynków w szkieletowej konstrukcji drewnianej. Przedmiotem badań było wyznaczenie nośności usztywniającej modułów, czyli ich nośności i sztywności na oddziaływania poziome, np. od wiatru. Przedstawione wyniki badań dotyczą badań ścian w układzie liniowym zgodnie z wymogami normy EN 594 [1].
EN
This paper presents the results of selected laboratory tests conducted on certified timber frame wall panels used for the construction of buildings. The research scope was to determine a racking stiffness of the panels, i.e. their carrying capacity and stiffness to resist a horizontal load in the plane of the panel, such as: wind load. The presented test results relate to tests of the linear arrangement of wall panels in accordance with the requirements of EN 594 [1].
Artykuł opisuje działania kontrolne dotyczące infrastruktury mostowej, jakie podjęte zostały przez autorów podczas nienormatywnego transportu drogowego elementów maszyny TBM. Maszyna miała być przewieziona od portu rzecznego k. Opola do m. Babica k. Rzeszowa, gdzie budowany jest tunel w ciągu drogi S19 Via Carpatia. Transport, w którym najcięższy pojazd miał ciężar prawie 500 ton, poruszał się po autostradach i drogach ekspresowych południowej i centralnej Polski. Na jego trasie zidentyfikowano prawie 400 obiektów mostowych, które poddano sprawdzeniu pod względem nośności i stanu technicznego. W opisywanych działaniach zastosowano innowacyjne rozwiązania chmurowe i mobilne, które pozwoliły na sprawne przeprowadzenie kontroli i zarządzanie całym procesem.
EN
The article describes the control activities regarding the bridge infrastructure, which the authors undertook during the non-normative road transport of TBM machine elements. The machine was to be transported from the river port near Opole to Babica near Rzeszów, where a tunnel along the S19 Via Carpatia road is being built. The transport, in which the heaviest vehicle weighed almost 500 tons, moved along the motorways and expressways of southern and central Poland. Nearly 400 bridge structures were identified along the route and checked in terms of load capacity and technical condition. In the described activities, innovative cloud and mobile solutions were used, which allowed for efficient control and management of the entire process.
Artykuł dotyczy realizacji zintegrowanego rozwiązania architektoniczno-budowlanego i urbanistycznego wzmocnienia osuwiskowej skarpy, o wysokości ok. 27 m, zlokalizowanej na obszarze zabytkowym z XIV-XX wieku w centralnej części miasta Mohylew (Białoruś). Realizacja była prowadzona w skomplikowanych warunkach geotechnicznych, spowodowanych występowaniem gruntów nasypowych o miąższości ok. 15 m oraz początkowych zjawisk utraty stateczności skarpy. Wzmocnienie skarpy musiało spełniać wymagania zachowania architektoniczno-zabytkowego charakteru terenu, a w szczególności miało zapewnić możliwość ruchu pieszych między skrajnymi poziomami skarpy. Całość wykonano w konstrukcji wielopoziomowych ścian oporowych, połączonych z wielobiegowymi schodami.
EN
The article is devoted to the integrated architectural, construction and urban planning solution usage experience description in order to strengthen a landslide slope with a height difference of more than 27 meters. The landslide slope is located in the XIV-XX centuries existing historical territory in the central part of the city of Mogilev (Belarus). It was necessary to solve the problem not only of the slope strengthening but also of preserving the existing architectural ensemble of the territory, and to provide a pedestrian connection between the levels of the slope in difficult geological conditions, with the presence of 14.7 meters of bulk soils. This task was solved by constructing a system of multi-level retaining walls, combined with a multi-flight staircase descent.
The main factors affecting the efficiency of the carrying capacity of drilling fluid are analysed in the paper. A description of the design of an experimental setup for modeling the well flushing process is presented, which makes it possible to evaluate the efficiency of the carrying capacity of a fluid from a variety of factors under study. To conduct experimental studies of the influence of factors on the efficiency of cleaning wells from cuttings, an experimental plan was built using the Taguchi methods for six factors at three levels of their change. According to the plan, we studied the effect of such parameters on the carrying capacity of the drilling fluid at various values of its flow rate: the variability of the drill string in the well; the cuttings particle diameter; the plastic viscosity of the drilling fluid; the pulsation frequency; the rotation of the drill string and its longitudinal movement. The nature of the formation of stagnant rock zones in the annulus of directional wells has been assessed. The influence of factors according to the constructed plan of the experiment at the distance of the beginning of settlement of the cuttings was studied. Based on the results of the studies, it was found that changing the range of these factors reduces the volume of rock deposited on the lower wall of the directional wellbore. It has been established that the use of a pulsating flow of flushing fluid makes it possible to reduce the value of its consumption and improve the efficiency of cleaning the annular space of wells from cuttings.
PL
W artykule przeanalizowano główne czynniki wpływające na efektywność nośności płuczek wiertniczych. Podano opis projektu eksperymentalnej instalacji do modelowania procesu płukania otworów, która pozwala na ocenę efektywności nośności płynu od różnych badanych czynników. W celu przeprowadzenia badań eksperymentalnych wpływu czynników na efektywność oczyszczania otworów ze zwiercin zbudowano plan eksperymentu metodami Taguchi dla sześciu czynników na trzech poziomach ich zmiany. Zgodnie ze skonstruowanym planem zbadano wpływ następujących parametrów na nośność płuczki wiertniczej przy różnych wartościach jej natężenia przepływu: mimośrodowość przewodu wiertniczego w otworze, średnica cząstek zwiercin, lepkość plastyczna płuczki wiertniczej, częstotliwość pulsacji, obrót przewodu wiertniczego i jego ruch wzdłużny. Oceniono charakter powstawania stref stagnacji cząstek skalnych w przestrzeni pierścieniowej odwiertów kierunkowych. Zgodnie ze skonstruowanym planem eksperymentu badano wpływ poszczególnych czynników na długość początkowego odcinka osadzania się zwiercin. Na podstawie wyników przeprowadzonych badań ustalono, że zmiana zakresu tych czynników zmniejsza objętość skały, która osadziła się na dolnej ścianie odwiertu kierunkowego. Stwierdzono, że zastosowanie pulsacyjnego przepływu płynu przemywającego pozwala na zmniejszenie wartości jej zużycia oraz poprawę efektywności oczyszczania przestrzeni pierścieniowej otworów ze zwiercin.
9
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
Prezentowane wyniki stanowią wstępne podsumowanie dotychczasowych badań własnych dotyczących połączeń zakładkowych, hybrydowych, nitowano-śrubowych. Rozważano elementy próbne z połączeniami dwuciętymi, w których jeden z nitów został wymieniony na śrubę wysokiej wytrzymałości. W poszczególnych elementach śruby osadzano w otworach zwykłych lub pasowanych, a następnie sprężano. Zagadnienie związane z wymianą nitów na śruby podjęto z uwagi na częste stosowanie takiej praktyki w przypadku remontów zabytkowych konstrukcji stalowych. Jednak nośność takich połączeń nie jest dotychczas potwierdzona badaniami modelowymi i analizami obliczeniowymi. Wyniki wykonanych badań zilustrowano na wykresach obciążenie - przemieszczenie, które można porównać z wynikami referencyjnymi dotyczącymi połączenia na dwa nity. Ponadto ustalono siłę niszczącą połączenia oraz oszacowano ich sztywność translacyjną. Ważnym etapem prowadzonych badań była analiza różnych układów łączników w połączeniu, a wnioski płynące z otrzymanych badań potwierdzają aktualny stan wiedzy zawarty w [1, 2].
EN
The results presented in this article are a preliminary summary of the authors’ research on the lap connections, hybrid joints, and riveted bolt joints. The analysed test elements with double-notched joints, in which one of the rivets was replaced with a high-resistance bolt. The bolts in specific elements were placed in regular or fitted holes and then pre-stressed. The issue related to the replacement of rivets with bolts was analysed due to the fact that this is a commonly used practice in the renovation of historic streel structures. However, the bearing capacity of those joints has not yet been confirmed by model studies with computational analyses. The results of the performed tests are presented in form of load-displacement diagrams, which may be compared to the reference results for double-riveted joints. A part from that, the joint breaking force was determined and the translational stiffness was assessed. An important element of the conducted research was the analysis of various arrangements of connectors in a joint. The results of the analyses confirm the current state of knowledge presented in publications [1, 2].
10
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
W pracy opisano przypadek stropu żelbetowego typu Filigran, dla którego przygotowano szereg opracowań opiniodawczych. Wynikało z nich, że strop kwalifikuje się do wzmocnienia przez usztywnienie, na skutek nadmiernych ugięć i drgań wpływających na komfort użytkowania. Wdrożono drogi i inwazyjny sposób wzmocnienia przez wymianę nadbetonu i wykonanie dodatkowych żeber. Jak się okazało, po dokładnych analizach dla pomierzonych i zbadanych charakterystyk, konstrukcja była bezpieczna. Jej nadmierne ugięcia były uchybieniem wykonawczym, a drgania dotyczyły jedynie warstw podłogowych i nie wynikały z tego, że konstrukcja nie ma wystarczającej sztywności.
EN
In the paper the case of the reinforced concrete ceiling of Filigran type was described, for which several consultative reports were prepared. According to them the ceiling was qualified for strengthening, by stiffening, as a result of excessive deflections and vibrations disturbing the comfort of exploitation. An expensive and invasive way of strengthening consisting of concrete topping replacement and additional ribs execution was implemented. As it was proved with a detailed analysis for measured and tested characteristics the structure was safe. Its excessive deflections was an execution fault. The vibrations involved only top floor layers and were not the consequence of the insufficient stiffness of the structure.
11
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
W słupach typu CFST w stanie granicznym dochodzi do zwiększenia wytrzymałości betonu rdzenia na skutek jego skrępowania. Zaistnienie tego zjawiska zależy od wielu czynników. Jednym z najważniejszych z nich jest sztywność obwodowa płaszcza stalowego. Jej wpływ na efektywność wzrostu wytrzymałości betonu rdzenia przebadano eksperymentalnie na grupie 48 grubościennych słupów CFST. Wykazano, że nadmierne zwiększanie grubości płaszcza słupa CFST nie przekłada się na wzrost jego nośności sprowadzonej. Jest wręcz przeciwnie: następuje jej spadek. Znacznie lepsze wykorzystanie pozytywnego wpływu skrępowania betonu rdzenia można osiągnąć z zastosowaniem rur cienkościennych niż grubościennych.
EN
In the limit state of the CFST columns, the core concrete strength increases due to its confinement. This positive effect depends on many factors. One of the most important is the ring stiffness of the steel tube. Its impact on the effectiveness of increasing the core concrete strength was experimentally tested on a group of 48 thick-walled CFST columns. It has been shown that an excessive increase in the tube thickness does not translate into an increase in its relative load capacity. On the contrary, it is decreasing. A much better use of the core concrete confinement can be achieved by using thin-walled tubes rather than thick-walled ones.
12
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
W artykule opisano badania ścian z autoklawizowanego betonu komórkowego (ABK) w skali naturalnej, w których zastosowano nowy typ zbrojenia z siatki stalowej. Omówiono wpływ zbrojenia na strefę połączenia ścian prostopadłych. Przeanalizowano nośność i rysoodporność połączenia. Wyniki porównano z wynikami badań wcześniejszych [1, 2]. Artykuł jest drugą częścią publikacji [3] oraz kontynuacją badań opisanych w [1, 2].
EN
The article describes the tests of walls made of autoclaved aerated concrete (AAC) on a full scale, in which the new type of steel mesh reinforcement was used. The influence of reinforcement on the connection zone of perpendicular walls was described. The load capacity and crack resistance of the connection zone were analysed. The results were compared with those of earlier studies [1, 2]. The article is the second part of the tests published in [3] and a continuation of earlier research [1, 2].
13
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
W artykule przedstawiono analizy numeryczne konstrukcji rusztowania z uszkodzeniami w postaci łukowego wygięcia stojaków. W przeprowadzonych obliczeniach analizowano wpływ lokalizacji i liczebności uszkodzeń, imperfekcji geometrycznych, normowych wariantów obciążenia oraz wysokości rusztowania na wielkość naprężeń normalnych. Celem przeprowadzonych analiz numerycznych jest zwiększenie poziomu wiedzy na temat wpływu uszkodzeń eksploatacyjnych na nośność głównych elementów konstrukcyjnych w rusztowaniach budowlanych.
EN
The paper presents numerical analyzes of the scaffolding structure with damages in the form of arc bending of the stands. In the calculations carried out, the influence of the location and number of damages, geometrical imperfections, standard load variants and scaffolding height on the value of normal stresses was analysed. The purpose of the conducted numerical analyzes is to increase the level of knowledge on the influence of operational damage on the load carrying capacity of the main structural elements in scaffolding.
W ostatnich latach w dużych miastach i na sąsiadujących z nimi terytoriach na Białorusi intensywnie rozwija się budownictwo na niezabudowanych terenach, które wcześniej (10-20 lat temu) były uważane za tereny, na których zabudowa nie jest możliwa ze względu na złe warunki gruntowe, konieczność wzmacniania podłoża i - co za tym idzie - wzrost kosztów wykonania budynków. W artykule opisano trzy obiekty: budynek przemysłowy, 19-kondygnacyjny budynek mieszkalny wielorodzinny i 5-kondygnacyjny budynek z zespołu budynków mieszkalnych. Przedstawiono warunki geologiczne terenów zabudowy i rozwiązania wgłębnego wzmocnienia podłoża za pomocą kolumn wypełnionych zaczynem cementowym zmieszanym z piaskiem lub betonem oraz wyniki terenowych, próbnych obciążeń stemplami i fragmentami fundamentów, a także porównanie pomierzonych osiadań z ich wartościami wyznaczonymi obliczeniowo.
EN
In recent years there has been intensive construction on vacant and undeveloped territories in large cities and in the territories adjacent to them in Belarus. Such kind of territories were previously (10-20 years ago) considered as areas where construction is too impossible due to poor ground conditions, or to the foundation erection costs will be comparable to the cost of building the above-ground part of the building. The materials of the article describe three objects (an industrial building, a high 19-storey multi-family residential building, and a of 5-storey building from the residential buildings complex), geological conditions of construction areas and vertical ground reinforcement solutions, as well as the staple and foundation fragment field load results and their comparison with the values, embed by calculation.
W artykule opisano metodę sprawdzania stanu granicznego nośności i ugięcia ściany wykonanej w technologii szkieletu drewnianego ze współpracującym poszyciem, poddanej działaniu obciążenia poziomego. Przedstawione procedury obliczeniowe wymagają od inżyniera, aby sięgał po zagraniczne wytyczne, często z krajów Ameryki Północnej. Jak wykazano, ich interpretacja bywa niespójna. Proces projektowania uzupełniono analizą numeryczną konstrukcji. Opisano metodę doboru parametrów modelu numerycznego, a wyniki odniesiono do obliczeń inżynierskich. Model MES posłużył do ujawnienia obrazu wytężenia konstrukcji i wyeliminowania błędnych rozwiązań konstrukcyjnych.
EN
The paper presents the procedure for checking the load bearing capacity and deflection of the wood framed shear wall with sheathing, subjected to a horizontal load. The applied calculation procedures force a modern engineer to reach for foreign guidelines, often from North American countries. Their interpretation is inconsistent, as it is presented. The design process was supplemented with a numerical analysis of the structure. The method of selecting the parameters of the FEM model was described, and the results were referred to the engineering analysis. The FEM model was used to reveal the stress image in the structure and to eliminate inappropriate design solutions.
Przedstawiono wyniki badań eksperymentalnych czterech śrubowych styków doczołowych belek o przekroju dwuteowym wysokości 1,0 i 1,5 m, z wieloma szeregami śrub i liczbą śrub 2, 4 i 6 w szeregach przy pasie rozciąganym. Na podstawie wyników badań i analizy MES stwierdzono, że ocena stanu granicznego nośności wielośrubowych styków doczołowych o modelu zniszczenia 2 i 3, przeprowadzona metodą składnikową wg PN-EN 1993-1-8, nie zapewnia ich bezpieczeństwa. Zaproponowano dwie metody modyfikacji metody składnikowej: MCM (Modified Component Method) i SRM (Stiffness and Rotation Method).
EN
Results of experimental tests of four extended multi-rows bolted end-plate beam splices of height 1,0 and 1,5 m having 2, 4 or 6 bolts in rows around tension flange, has been presented. On the basis of tests and FEM results it was concluded that moment resistance of joints with 2 and 3 failure mode calculated using component method of EN 1993-1-8 is highly underestimated and not safe. Two modification methods have been proposed: MCM (Modified Component Method) and SRM (Stiffness and Rotation Method).
W artykule podano metody wzmacniania wsporników słupów, których skuteczność została zweryfikowana badaniami eksperymentalnymi. Niezależnie od zastosowanej metody efektywność wzmocnienia wspornika jest głównie uzależniona od smukłości ścinania wspornika, ilości zbrojenia wewnętrznego i jego wytężenia przed wzmocnieniem.
EN
The article presents the methods of strengthening R-C corbels, the effectiveness of which has been verified by experimental research. Regardless of the method used, the effectiveness of the corbel strengthening is mainly dependent on the shear span to effective depth ratio, the amount of internal reinforcement and the effort of corbel before strengthening.
An unsaturated polyester resin (UPR) mortar was applied to repair the damage to the tension zone's one-way reinforced concrete (RC) slabs. The load carrying capacity of the patched RC slab is of interest to justify the effectiveness of the repair. The Yield Line Theory (YLT) may be used to estimate the load carrying capacity of patched RC slabs under concentrated load. The results of the YLT are compared with the experimental results to evaluate the validity of the YLT method. The results confirm that patching alters the yield line formation, mainly when the concentrated load is applied close to the patching zone. Subsequently, the YLT method provides a higher load carrying capacity estimation deviation for slabs with a loading point near the patching zone. On the other hand, the YLT method estimates load carrying capacity accurately when the loading point is away from the patching zone.
19
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
Zamieszczono zalecany w wytycznych ATV tok obliczeń nośności rur, który należy uznać za przybliżony. Następnie podano proponowany dokładniejszy tok obliczeń. Dokonano przeglądu zaleceń dotyczących ustalania współczynnika posadowienia, mającego bardzo istotny wpływ na nośność rur po ich wbudowaniu. Zamieszczono trzy przykłady różnych posadowień rur, wskazując jakie konsekwencje wynikają z bardziej niekorzystnego oraz bardziej korzystnego posadowienia rur, w stosunku do posadowień zalecanych przez projektanta.
EN
The method of calculating the load capacity of pipes recommended in the ATV guidelines is given. It is approximate. Then, the proposed exact method of calculations is given. The recommendations for determining the bedding coefficient, which have a very significant impact on the load capacity of pipes after their installation, have been reviewed. There are three examples of different pipe beddings indicating the consequences of more unfavorable and more favorable pipe beddings in relation to the recommended beddings.
Zagadnieniem omawianym w ramach artykułu jest innowacyjny system konsoli nośnych z przekładkami z tworzywa sztucznego. W ramach zleconych prac i grantów badawczych Koła Naukowego Konstrukcji Metalowych przeprowadzono badania konsoli poliamidowo-aluminiowych. Dostarczone wieszaki o różnych parametrach geometrycznych i materiałowych zostały przebadane w przestrzennej maszynie wytrzymałościowej znajdującej się na Wydziale Inżynierii Lądowej Politechniki Warszawskiej. Celem badań było określenie nośności konsoli na zginanie w płaszczyźnie, rozciąganie osiowe i wpływ zmęczenia. Następny krok obejmował przygotowanie analizy numerycznej w programie Abaqus CAE dla wybranego typu konsoli. Celem analizy MES było osiągnięcie końcowego stanu odkształcenia zgodnego z rzeczywistym, uzyskanym w ramach badań laboratoryjnych. W podsumowaniu przedstawiono wnioski wyciągnięte z porównania wyników uzyskanych w ramach badań laboratoryjnych i analizy numerycznej.
EN
The issue discussed in the article is an innovative system of support consoles with plastic spacers. As part of the commissioned works and research grants of the Koła Naukowego Konstrukcji Metalowych, tests of polyamide - aluminum consoles were carried out. Supplied hangers with different geometrical and material parameters were tested in a spatial testing machine located at the Faculty of Civil Engineering of the Warsaw University of Technology. The aim of the tests was to determine the bearing capacity of the console for in-plane bending, axial stretching and the effect of fatigue. The next step involved the preparation of a numerical analysis in the Abaqus CAE program for the selected type of console. The purpose of the FEM analysis was to achieve the final state of deformation consistent with the real one obtained during laboratory tests. The summary presents the conclusions drawn from the comparison of the results obtained as part of laboratory tests and numerical analysis.
JavaScript jest wyłączony w Twojej przeglądarce internetowej. Włącz go, a następnie odśwież stronę, aby móc w pełni z niej korzystać.