Techniques for measuring fluid flow have been known since the 19th century. The first solutions based on the use of pressure only allowed relatively slow changes to be observed. It was not until measurement techniques based on the use of electronic components and the phenomenon of thermo-transfer, combined with a method enabling fast signal recording (A/C converters), that it became possible to analyse the flow of a medium (e.g. air) in detail. Although flow sensors based on measuring changes in resistance have been known for many years, new solutions are still being developed. This paper presents the results of a study using three sensors. Their response to laminar airflow was investigated for different velocities (1.2 - 2.6 m/s). The flow forcing was implemented using an axial fan and the signals were measured simultaneously for all the sensors tested. The results showed which sensors had the smallest dispersion of results (PAN and WA sensors) and confirmed that for the investigated velocity variations (0.14 m/s pitch) the results are unambiguously interpretable.. It should be noted that sensor research is related to the need to develop a device to measure flow as accurately as possible, while at the same time ensuring the comfort of the test person during the measurements. Therefore, the search was for a sensor that is small in size and at the same time resistant to damage and operation in a harsh humid environment.
W artykule opisano historię techniczną mostu w Krzyżowicach. Obiekt intensywnie osiadał, ale brak było istotnych przemieszczeń na łożyskach. Górnicze osiadanie terenu spowodowało znaczne zmniejszenie światła pionowego, tj. obniżenie mostu względem zwierciadła rzeki, konieczna była przebudowa mostu. Po przebudowie mostu wydłużono ściany górnicze poza obiekt, w krótkim czasie doszło do znacznych zmian w położeniu przyczółków. W artykule opisano starą konstrukcję mostu, nową konstrukcję mostu, podano wyniki długoletnich obserwacji i pomiarów oraz wskazano, jak należy projektować zabezpieczenia na wpływy górnicze w przypadku nietypowych wymuszeń górniczych.
EN
Article describes the technical history of a bridge in Krzyżowice. The object settled intensively, but there were no significant displacements on the bridge bearings. Mining subsidence caused a significant reduction in vertical light, i.e. lowering the bridge in relation to the river level, it was necessary to rebuild this bridge. After the reconstruction of the bridge, mining walls were extended beyond the object, in a short time there were significant changes in the position of the abutments. The article describes old bridge construction, new bridge construction, gives the results of long-term observations and measurements, and indicates how to design protection against mining influences in the case of unusual mining impacts.
3
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
The current study aims to calculate and assess the asymmetry of the two goatfish species, Yellowstripe goatfish Mulloidichthys flavolineatus (Lacepède 1801) and Red Sea goatfish, Parupeneus forsskali (Fourmanoir & Guézé 1976) collected from Hurghada fishing harbour, Egypt. The asymmetry valuation for M. flavolineatus and P. forsskali is imperative to demonstrate the impact of asymmetry on the larvae settlement in this vital fishing ground. Asymmetry was calculated for the saccular otolith (Sagittae) biometry, namely length, width, and mass. The results showed that the otolith height had a lower asymmetry value than the otolith length for the two goatfish species inspected. No relationship between the asymmetry value of otolith length and width and total fish length was observed. Both goatfish species’ calculated otolith mass asymmetry was higher than that of many teleost fish species.
One of the main tasks of contemporary hydrology is to plot the best possible rating curve, which has numerous applications in practical hydrological problems. The quality of the curve depends to a significant degree on the precision of hydrometric measurements and the precision in determining the relationship between discharge and the stage (water level). In this study, we engage the multidimensional problem of non-homogeneity of hydrometric data. The distances between a given point of measurement and the given cross-section proved to be highly diverse. Hence, we propose data transformation so that every measurement can be treated as taken in a given cross-section. The transformation allows partial homogenization of measurement data. An automatic non-linear method for estimating the rating curve is also proposed. The method has been tested on selected representatives of mountain, submontane, and lowland rivers of the Oder River catchment basin (Lower Silesia, Poland). Cross-sections selected for analysis were: Łąki on the Barycz River, Lądek Zdrój on the Biała Łądecka River, Jelenia Góra on the Bóbr River, Jakuszyce on the Kamienna River, and Łozy on the Kwisa River.
Decyzje i działania (odpowiedzi) podejmowane na podstawie pełnej i wiarygodnej analizy czynników sprawczych, presji, zmiany parametrów stanu i ich wpływu na środowisko, społeczeństwo oraz gospodarkę mogą z dużym prawdopodobieństwem w długoterminowej perspektywie przynieść pożądane efekty. W artykule opisano model DPSIR (driving forces, pressures, state, impact, responses; odpowiednio: czynniki sprawcze, presje, stan, wpływ, odpowiedzi) służący do szczegółowej analizy interakcji pomiędzy czynnikami antropogenicznymi a środowiskiem. Tworzony model DPSIR będzie skutecznym narzędziem do zarządzania jakością powietrza. W artykule przedstawiono badania prowadzone w Akademii Górniczo-Hutniczej, które zostaną wykorzystane jako jedne z wielu danych wejściowych w powstającym modelu DPSIR. Opracowywany model będzie jednym ze składowych zaawansowanego narzędzia tworzonego na AGH, w ramach Obserwatorium Transformacji Energetycznej (OTE), które umożliwi przygotowanie rekomendacji optymalnych działań dotyczących realizacji polityki energetycznej i poprawy jakości powietrza w Polsce.
EN
Decisions and actions taken base on analysis of the driving forces factors, pressures, changes in the parameters of the condition and their impact on the environment, society and economy may help to archive long term effects. This article describes the DPSIR (Driving Forces-Pressures-State-Impact-Responses) model for the analysis of anthropogenic and environmental interactions. The article describes the above-mentioned main components of the model and their meaning, which allows for the determination of air quality in Poland. In addition, selected research conducted at the AGH University of Science and Technology, which is part of the DPSIR model, is presented. The developed model will be one of the components of the advanced tool created by AGH, i.e. the Observatory of Energy Transformation (OTE), which will enable the preparation of recommendations for optimal actions regarding the implementation of energy policy and improvement of air quality in Poland.
W artykule przedstawiono najważniejsze zmiany w treści Ramowej Instrukcji Eksploatacji Transformatorów, które zostały wprowadzone w wyd. 2022 r. Omówiono również przyczyny nowelizacji spowodowane zmianami w aktach normatywnych i przepisach, stosowaniem nowoczesnych materiałów konstrukcyjnych oraz wprowadzaniem nowych metod pomiarowych i potrzebą dopasowania wymagań do zmieniającej się populacji transformatorów oraz czynników ekonomicznych i środowiskowych.
EN
The article presents the most important changes in the General Transformer Maintenance Guide, that have been introduced to ed. 2022. The reasons for he revision caused by changes in normative acts and regulations, the use of modern construction materials, the introduction of new measurement methods end the need to adjust the requirements to the changing population of transformers as well as economic and environmental factors are also discussed.
W artykule przedstawiono zasady pomiaru pochyleń budynków spowodowanych podziemną eksploatacją górniczą. Wartość pochylenia może być miarą utraty wartości technicznej i ekonomicznej obiektu. Natomiast składowe pochylenia wzdłuż osi budowli wykorzystuje się w projektach technicznych rektyfikacji (prostowania) oraz analizach wytężenia istniejących konstrukcji. Pomiary pochyleń budynków są wykonywane na zewnątrz budynku i w pomieszczeniach wewnętrznych. Pochylenia są określane klasycznymi metodami geodezyjnymi przy zastosowaniu niwelatora lub teodolitu, a także z użyciem poziomicy elektronicznej z cyfrowym odczytem wyniku - pomiaru. W drugiej części artykułu zamieszczono dwa przykłady pomiaru pochyleń podłóg i wychyleń ścian od pionu, wyniki pomiarów i ich interpretację.
EN
The article presents the principles of measuring building inclinations caused by underground mining. The value of the inclination can be a measure of the loss of technical and ecomnomic value of an object. The components of the inclination along the axis of the building are used in technical rectification (straightening) projects. Building inclinations are measuring outside and inside building. The inclinations are determined by classical geodetic methods with use of a leveler or theodlite, as well as electronic spirit level with digital readout of the measurement result. The second part of the article presents two examples of measuring floor and wall inclinations from vertical level, as well as measurement results and their interpretation.
Przedstawiono charakterystykę systemów radiokomunikacyjnych emitujących promieniowanie elektromagnetyczne (PR-EM) rozpoznane w budynkach użyteczności publicznej. Zaprezentowano wyniki badań PR-EM w budynkach użyteczność publicznej w środowisku miejskim, charakteryzującym się największym zagęszczeniem anten nadawczych oraz PR-EM o najbardziej złożonym widmie częstotliwości. Wykazano, że głównymi źródłami ekspozycji na PR-EM w budynkach są zewnętrzne stacje bazowe sieci telefonii mobilnej 4G/5G (pasma downlink: GSM 900 oraz LTE 800, 1800, 2100 i 2600) i naziemnych nadajników radiowo-telewizyjnych (FM i TV VHF i UHF), o ile są one zlokalizowane na terenie miasta, oraz wewnętrzne sieci lokalnej łączności między urządzeniami i dostępu do Internetu (Wi-Fi 2,4GHz i 5GHz). Wyniki badań wykazały, że w typowych warunkach lokalizacji zewnętrznych anten systemów radiokomunikacyjnych ekspozycja na PR-EM w budynkach użyteczności publicznej nie przekraczała dolnego limitu strefy pośredniej (ekspozycja pomijalna określona przez prawo pracy). W przypadku lokalizacji wewnątrz budynków źródeł PR-EM mogą one mieć najistotniejszy udział w profilu występującej tam ekspozycji. Zaprezentowano również kluczowe elementy postępowania podczas oceny i ograniczania PR-EM w budynkach użyteczności publicznej.
EN
The characteristics of radiocommunication systems as the main sources of exposure to electromagnetic radiation (EMR) in public utility buildings are presented. The results of EMR research in public utility buildings in an urban environment characterized by the highest density of transmitting antennas and EMR with the most complex frequency spectrum are presented. It has been shown that the main sources of exposure to EMR in buildings are external base stations of the 4G/5G mobile communications network (downlink: GSM 900 and LTE 800, 1800, 2100 and 2600 bands), terrestrial radio and television transmitters (FM and TV VHF and UHF) if they are located in the city, and internal networks of local communication between devices and access to the Internet (Wi-Fi 2.4GHz and 5GHz). The investigation results showed that under typical conditions of location of external antennas of radiocommunication systems, exposure to EMR in public buildings did not exceed the lower limit of the intermediate zone where protection of workers against EMR is applicable (negligible exposure defined by labour law). In the case of EMR sources located inside buildings, they may have a significant contribution to the exposure profile. The key elements of the procedure for EMR assessments and limiting EMR radiation in public buildings were also presented.
9
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
W artykule przedstawiono proces budowania oraz testowania zdalnego, całkowicie autonomicznego systemu pomiaru parametrów pracy wentylatorów. Proces zrealizowano w ramach pierwszego etapu innowacyjnego projektu. Przedstawiono szczegółowe kroki budowy systemu zbierania i przetwarzania danych pomiarowych z wentylatorów zainstalowanych w rzeczywistych warunkach eksploatacji oraz wyniki ich analizy. W szczególności opracowano i wdrożono infrastrukturę pomiarową w tym również zdefiniowano zestaw niezbędnej aparatury pomiarowej. Zamontowano aparaturę pomiarową na wyselekcjonowanych instalacjach z odpowiednimi wentylatorami. Wdrożono systemy pozwalające na ciągłe pomiary parametrów instalacji, zdalny przesył danych na serwer, gdzie poddawany jest bieżącej analizie i selekcji zebranych danych do wykorzystania w procesie modelowania i diagnostyki. Zweryfikowano eksperymentalnie zadowalający stopień korelacji między wyselekcjonowanymi parametrami mierzonymi w warunkach rzeczywistych, a charakterystyką wentylatora i instalacji. Wyznacznikiem tego było znalezienie czterech istotnych statystycznie parametrów na poziomie ufności 95%.
EN
The article presents the process of building and testing a remote, fully autonomous system for measuring fan operating parameters. The process was completed as part of the first stage of an innovative project. The paper includes detailed steps of constructing a system for collecting and processing measurement data from fans installed in their operating conditions and the results of their analysis. In particular, the measurement infrastructure was developed and implemented, including determining a set of necessary measurement equipment. Measuring equipment was installed in selected fans installations. Systems have been implemented that allow for continuous measurement of installation parameters and remote data transmission to the server, followed by an ongoing analysis and selection of the collected data for use in the modeling and diagnostics process. A satisfactory degree of correlation between the selected parameters measured in actual operating conditions and the characteristics of the fan and the installation was verified experimentally. Its indication was finding 4 statistically significant parameters at the confidence level of 95%.
W artykule przedyskutowano zagadnienie wykorzystania nadprzewodników do pomiaru pól magnetycznych. Rozpatrzono działanie cienkowarstwowych, wysokotemperaturowych nadprzewodnikowych interferometrów kwantowych SQUID-ów, które znajdują coraz szersze zastosowanie, szczególnie w biomedycynie. Przedstawiono zakres pól magnetycznych występujących w przyrodzie i stosowalność do ich pomiaru SQUID-ów.
EN
The article discusses the issue of using superconductors to measure magnetic fields. Operation of thin-film high-temperature superconducting quantum interferometers SQUID-s, which are increasingly used, especially in biomedicine, was considered. The scope of the magnetic fields occurring in nature and the applicability to their measurement of SQUIDs were presented.
This article presents the results of measurements of a belt transmission with a poly-V belt 5PK, most often used in the industry, especially in industrial drives, agricultural machines and in the automotive industry. The main goal of the works was to obtain the dependence of the belt slip value on the measured, relatively high values of resistance torque. For this purpose, a series of measurements were made using a specialised research stand consisting of two alternating current motors and attached pulleys. It considered four cases of the value of the belt pre-tensioning force. In each of the cases, while making the measurements, the resistance of the passive pulley was increased, resulting in increasing values of belt slip. Finally, the achieved courses were approximated. The obtained results will be used to develop empirical models of friction at the belt-pulley interface. They can also be useful for belt manufacturers to make better belts, especially those subjected to higher loads.
The Santos Juanes Church in Valencia, Spain, is one of the most important religious buildings in the city. Based on this church, this work proposes an analysis that can be extrapolated to other historic buildings where, like this one, no detailed documents on constructive measurement reasons exist. Hence the present work outlines the unpublished hypothesis of how the sequential process of traces on both the plan and section might have been based on the different ancient and medieval architectural treatises. All this will allow the existing intrinsic relations between the shape of the building and its current aesthetics to be obtained through a metric and geometric analysis of the church.
PL
Kościół Santos Juanes w Walencji jest jednym z najważniejszych budynków sakralnych miasta. Na podstawie tej świątyni artykuł proponuje analizę, która może być przeniesiona na inne budynki historyczne, nieposiadające – podobnie jak ona – szczegółowej dokumentacji dotyczącej wymiarów konstrukcyjnych. W związku z tym tekst przedstawia niepublikowaną hipotezę odnośnie do sekwencyjnego rozmierzania zarówno rzutu, jak i przekroju, które mogło być oparte na różnych starożytnych i średniowiecznych traktatach. Wszystko to pozwoli ustalić relacje pomiędzy kształtem budynku i jego obecną estetyką poprzez metryczną i geometryczną analizę kościoła.
This paper presents recent progress in the knowledge concerning the stochastic theory of bio- hydrodynamic lubrication with a phospholipids bilayer. On the basis of experimental measurements and analytical solutions, the research concerns the determination of the random expectancy values of load carrying capacity, the friction coefficient, and synovial fluid dynamic variations. After numerous measurements, it directly follows that the random density function of the gap height in the human joint usually indicates a disorderly increases and decreases in the height. Such irregular gap height variations have an important influence on the random synovial bio-fluid dynamic viscosity. This finally leads to the friction coefficient and cartilage wear changes of cooperating bio- surfaces. The main topic of this paper relates to the expectancy values of the tribology parameters localized inside the variable stochastic standard deviation intervals of the human joint gap height. The results obtained finally indicate the influence of the random roughness and growth of living biological cartilage surfaces on the expectancy values of the synovial fluid dynamic viscosity, load carrying capacity and friction forces in human hip joints.
PL
Niniejsza praca przedstawia ostatnie osiągnięcia wiedzy w zakresie losowej teorii biohydrodynamicznego smarowania z udziałem fosfolipidów. Badania dotyczą losowych wartości oczekiwanych dla nośności, współczynników tarcia, zmian lepkości dynamicznej cieczy synowialnej, przeprowadzone na podstawie pomiarów doświadczalnych i obliczeń analitycznych. Z przeprowadzonych pomiarów doświadczalnych wynika, że losowa funkcja gęstości wysokości szczeliny w stawach człowieka wykazuje zazwyczaj nieprzewidywalne zmiany wysokości szczeliny. Takie nieregularne zmiany mają istotny wpływ na wartość lepkości cieczy biologicznej. Dlatego zmienia się współczynnik tarcia oraz zużycie biopowierzchni. Głównym celem pracy jest wyznaczenie losowej wartości oczekiwanej parametrów tribologicznych umiejscowionych wewnątrz zmiennego losowego przedziału odchylenia standardowego wysokości szczeliny stawu człowieka. Końcowe rezultaty uzyskane w pracy wykazują wpływ losowych chropowatości oraz wzrostu żywych powierzchni chrząstki stawowej na losowe wartości oczekiwane lepkości dynamicznej cieczy synowialnej, nośności, siły tarcia w stawie biodrowym człowieka.
14
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
Artykuł porusza tematykę zarówno możliwości pomiarowych, jak i możliwej do osiągnięcia dokładności wybranych narzędzi pracujących w ramach współrzędnościowej techniki pomiarowej. Skoncentrowano się na przedstawieniu dwóch powszechnie stosowanych w praktyce przemysłowej narzędzi pomiarowych – współrzędnościowej maszyny pomiarowej i ramienia pomiarowego – w kontekście kontroli wymiarowo- kształtowej detalu testowego. W obu omawianych przypadkach zastosowano układy współrzędnych oparte na metodzie najlepszego dopasowania, jednak same metody pomiarowe były różne.
EN
The article addresses the measurement capabilities and the achievable accuracy of selected tools working within the frames of the coordinate measurement technology. It focuses on presenting two commonly used industrial measuring tools – coordinate measuring machine and measuring arm – in the context of dimensional and shape control of a test detail. In both cases, coordinate systems based on the best fit method were used, but the measurement methods themselves were different.
Groundwater temperature is the basic physical parameter that determines the state and energy measure of the physical system while being an important indicator of the status of groundwater and aquifers. This article presents considerations on the temperature of fresh groundwater of the active exchange zone and their importance for the recognition of hydrogeological conditions. Review of groundwater temperature results application to analyze groundwater recharge process, flow and depth of circulation has been presented. It has been showed also how the water temperature supports evaluation of the groundwater chemical composition changes, the extension of contaminants, the hydraulic conductivity evaluation and the application in groundwater flow modelling study. A wide range of temperature variation in shallow waters of up to 20.3°C has been demonstrated based on measurements in the Quaternary aquifer in the Wrocław City infiltration intake and deep waters from the Neogen aquifer. Up to a depth of 10-17 m, significant seasonal temperature changes with depth have been documented. It was recommended to establish a neutral depth for the correct interpretation of the groundwater thermal field. Opposite spring water from a deeper aquifer of Cretaceous formations in the Stołowe Mts. documented an almost constant temperature higher by 4.6°C from the average air temperature. This indicates the range of groundwater flow depth of 170m below the land surface. A simple formula based on the density value of the heat flux, taking into account the average air temperature proposal, allows to calculating the depth of water flow. The methodical conditions for temperature measuring and the depth of location of temperature recording probesas well as their limitations, have been identified.
The aim of the study is to assess the accuracy of mapping the internal structure and shape of phantoms in computed tomography (CT) imaging, using reconstructive metrology and virtual measurements. The tests material is tomographic imaging of diagnostic phantoms: the head phantom used for monthly calibrations of computer tomographs and the specialized phantom for tests performed once a year. The Materialize Mimics computer program was used to measure the geometry of objects inside the phantoms and to measure the radiological density in the cross-sections of the tested patterns. It is a universal tool for assessing the accuracy of mapping in CT imaging. The results of the measurements were used to perform a complete statistical analysis. The values of standard deviations for the performed measurements did not exceed the limit value, which means that the tested tomograph meets the requirements for homogeneity of imaging and noise level specified in the Regulation of the Minister of Health. The proposed procedure is important for the target device, but can also be a tool for comparing the quality of different tomographs.
PL
Celem pracy jest ocena dokładności odwzorowania struktury wewnętrznej i kształtu fantomów w obrazowaniu tomografią komputerową (CT), z zastosowaniem metrologii rekonstrukcyjnej i pomiarów wirtualnych. Materiałem badań jest obrazowanie tomograficzne fantomów diagnostycznych: fantomu głowy używanego do comiesięcznych kalibracji tomografów komputerowych i fantomu specjalistycznego do testów wykonywanych raz w roku. Do pomiarów geometrii obiektów znajdujących się wewnątrz fantomów oraz pomiarów gęstości radiologicznej w przekrojach badanych wzorców wykorzystano program komputerowy Materialise Mimics. Stanowi on uniwersalne narzędzie do oceny dokładności odwzorowania w obrazowaniu CT. Wyniki pomiarów wykorzystano do przeprowadzenia pełnej analizy statystycznej. Wartości odchyleń standardowych dla wykonanych pomiarów nie przekroczyły wartości granicznej, co oznacza, że badany tomograf spełnia wymogi odnośnie do jednorodności obrazowania i poziomu szumów, ujęte w Rozporządzeniu Ministra Zdrowia. Zaproponowana procedura jest istotna dla docelowego urządzenia, ale może również stanowić narzędzie do porównania jakości różnych tomografów.
The modern automotive industry invests more and more in electric drive technology. As a result, new challenges arise in terms of vibroacoustic optimization of the car interior. Components that were once masked by the internal combustion engine are starting to dominate the interior of vehicles. There is therefore a great need for noise reduction. For this purpose, a number of methods of its reduction are used, i.e. component optimization (source), use of active noise reduction systems or passive soundproofing materials. In order to perform the abovementioned noise reduction measures, appropriate measurements and signal analysis should be carried out. This presentation aims to present the measurement of an automotive air cooler in transient states on the stand. Measurements were made using a 3D intensity probe based on the direct measurement of the acoustic particle velocity, in 3 planes in front of the cooler. Then, order tracking analysis was performed for the run-up and coast-down. The results in the form of selected orders of intensity and acoustic particle velocity were compared with classical results made with the use of a microphone at the same measurement points locations.
PL
Współczesny przemysł motoryzacyjny inwestuje coraz bardziej w technologię napędu elektrycznego. W związku z tym pojawiają się nowe wyzwania w zakresie optymalizacji wibroakustycznej wnętrza samochodu. Komponenty, które kiedyś były maskowane przez silnik spalinowy zaczynają dominować we wnętrzu pojazdów. Istnieje zatem duża potrzeba redukcji hałasu. W tym celu stosuje się szereg metod jego redukcji, tj. optymalizacja komponentu (źródła) zastosowanie aktywnych systemów redukcji hałasu lub pasywnych materiałów wygłuszających. Aby dokonać wspomnianych zabiegów redukujących hałas, należy przeprowadzić stosowne pomiary oraz analizę sygnałów. Niniejsza prezentacja ma na celu przedstawienie pomiaru chłodnicy samochodowej w stanach nieustalonych na stanowisku. Pomiarów dokonano przy użyciu sondy natężeniowej 3D bazującej na bezpośrednim pomiarze prędkości akustycznej cząsteczek, w 3 płaszczyznach przed chłodnicą. Następnie wykonano analizę rzędów (order tracking) dla rozbiegu oraz wybiegu. Wyniki w formie wybranych rzędów (orderów) natężeń oraz prędkości akustycznej cząstek zestawiono z klasycznymi wynikami wykonanymi przy użyciu mikrofonu w tych samych punktach pomiarowych.
This paper presents the design method and the construction details of a subsonic low-speed wind tunnel, which has been designed to achieve the flow velocity of 35 m/s in the measurement section with expected uniform velocity field at its inlet. To achieve such objectives a very detailed design was performed using a theoretical 1D analysis and computational fluid dynamics simulations. This approach was applied to improve the flow quality along the wind tunnel sections. When the wind tunnel has been launched a direct comparison of the experimentally measured flow field in the test section and numerical simulation results was conducted. Such comparison of the simulation results with the experimental one is presented in this paper. The obtained results confirm that assumed wind tunnel design method was correct, i.e. the pressure drop in the wind tunnel has been predicted very well and drive system is effective and sufficient to accelerate the airflow to required values.
This paper presents the results of experimental research on heat transfer distribution under the impinging jets at high jet velocity on curved surfaces. The air jets flow out from the common pipe and impinge on a surface which is cooled by them, in this way all together create a model of external cooling system of low pressure gas turbine casing. Preliminary measurement results from the flat plate case were compared with the results from the curved surface case. Surface modification presented in this paper relied on geometry change of flat surface to the form of a ‘bump’. The special system of pivoted mirrors was implemented during the measurements to capture the heat exchange on curved surfaces of the bump. The higher values of mean heat transfer coefficient were observed for all flow cases with a bump in relation to the reference flow case with a flat plate.
Przedmiotem opracowania jest gotyckie sklepienie w prezbiterium kościoła w Szydłowcu. Powiązany z nim jest oryginalny dużych rozmiarów ryt, zachowany na ścianie nawy głównej, pełniący podczas realizacji świątyni funkcję swoistego „projektu wykonawczego”. To unikat w skali europejskiej i jedyny taki zespół śladów dawnego rzemiosła budowlanego. Ryt, odkryty po pięciu wiekach, wzbudził duże zainteresowanie badaczy wskazujących nieliczne przypadki podobnych rysunków, zachowanych jednak fragmentarycznie na posadzkach, tarasach, ścianach czy sklepieniach. Na przestrzeni lat powstały hipotezy rekonstrukcyjne dotyczące faz rysunkowych i realizacyjnych tego dzieła w Szydłowcu. Autorów artykułu zainteresowały zależności między projektem a zrealizowanym kształtem sklepienia, czyli zagadnienie, w jakim stopniu odwzorowano w naturalnej skali koncepcje zapisane na płaskim rysunku. Dokonano analizy porównawczej przebiegu żeber ze stanem istniejącym wymurowanych segmentów kamiennych łuków żebrowych. Podczas prac zastosowano nowoczesny sprzęt pomiarowy i zaawansowane oprogramowanie. Celem badań było określenie i sklasyfikowanie wzajemnych podobieństw i różnic.
EN
This paper discusses Gothic vault located in the presbytery of a church in Szydłowiec. It is linked with an original, large engraving that has survived in the wall of the church’s main nave, and acted as a sort of “construction- phase design” during the church’s construction. It is a unique specimen on the European scale and the only complex of traces of historical construction craftsmanship of its kind. The engraving, uncovered after five centuries, inspired considerable interest in scholars who pointed to rare cases of similar drawings that have been only fragmentarily preserved on floors, terraces, walls or vaults. Over the years, reconstructive hypotheses were formulated concerning the drawing and construction phases of the Szydłowiec vault. The authors became interested in the dependencies between the design and the geometry of the vault as built, i.e. the degree to which the conceptual proposals recorded on the drawing were expressed on a natural scale. The authors performed a comparative analysis of the outline of the ribs, comparing them with the existing state of the ribbed stone arch segments. Modern measurement equipment and advanced software was used. The goal of the study was to determine and classify similarities and differences between the elements.
JavaScript jest wyłączony w Twojej przeglądarce internetowej. Włącz go, a następnie odśwież stronę, aby móc w pełni z niej korzystać.