Przedmiotem opracowania jest ocena nośności wiaduktu kolejowego. Analizie poddano wiadukt o konstrukcji żelbetowej zbrojony belkami stalowymi. Obiekt znajduje się w okolicach wsi Bukowina w Gminie Dywity, województwo warmińsko-mazurskie. Zasadniczym celem pracy jest ocena nośności mostu, która poprzedzona była przeprowadzeniem inwentaryzacji obiektu. Identyfikacji poddano geometrię konstrukcji oraz zbadano klasę wytrzymałości betonu, z którego wykonano konstrukcję. Przeprowadzono również obliczenia, na podstawie których dokonano oceny nośności badanego wiaduktu. Do obliczeń wykorzystano dwie procedury obliczeniowe: belka obetonowana i przekrój zginany zbrojony wkładkami sztywnymi. W oparciu o przeprowadzoną analizę wykazano, iż pomimo nieestetycznego wyglądu mostu spełnia on wymogi użytkowalności, a jego nośność jest zapewniona.
EN
The subject of the study is the assessment of the loadbearing capacity of a railway viaduct. The analysis involved a viaduct with a reinforced concrete structure, which is strengthened by steel beams. The facility is located near the village of Bukowina in the Dywity Commune, Warmian-Masurian Voivodeship. The main aim of the work is to assess the bridge’s load capacity, which was preceded by an inventory of the facility. The geometry of the structure was identified, and the concrete’s strength class, from which the structure was made, was examined. Calculations were also carried out, based on which the load capacity of the tested viaduct was assessed. Two calculation procedures were used: encased beam and bent cross-section reinforced with rigid inserts. Based on the conducted analysis, it was shown that despite the unattractive appearance of the bridge, it meets usability requirements, and its load-bearing capacity is ensured.
Zmieniające się warunki użytkowania istniejących elementów konstrukcji determinują konieczność wykonania powtórnej weryfikacji nośności. Zadanie takie może komplikować się w świetle wielu zmiennych, które należy uwzględnić podczas analizy ustrojów. W artykule przywołano dwa przypadki obiektów już eksploatowanych, na dachach których planowano zamocować panele fotowoltaiczne. Ocena możliwości dodatkowego ich dociążenia poprzedzona została sporządzeniem projektów branżowych, zawierających m.in. lokalizację (rozkład) paneli, jak również ich ciężar. W artykule ten problem opisano jako studium przypadku dla dwóch niezależnych dachów, wykonanych w różniących się technologiach.
EN
The changing conditions of use of existing structure elements determine the need to re-verify the load-bearing capacity. Such a task may become more complicated in light of the many variables that must be taken into account when analyzing systems. The article mentions two cases of facilities already in operation, on the roofs of which photovoltaic panels were planned to be installed. The assessment of the possibility of additional load was preceded by the preparation of industry projects, including, among others: location (distribution) of panels as well as their weight. The article describes this problem as a case study for two independent roofs made using different technologies.
W artykule przedstawiono wyniki wybranych badań laboratoryjnych certyfikowanych modułów do wykonywania budynków w szkieletowej konstrukcji drewnianej. Przedmiotem badań było wyznaczenie nośności usztywniającej modułów, czyli ich nośności i sztywności na oddziaływania poziome, np. od wiatru. Przedstawione wyniki badań dotyczą badań ścian w układzie liniowym zgodnie z wymogami normy EN 594 [1].
EN
This paper presents the results of selected laboratory tests conducted on certified timber frame wall panels used for the construction of buildings. The research scope was to determine a racking stiffness of the panels, i.e. their carrying capacity and stiffness to resist a horizontal load in the plane of the panel, such as: wind load. The presented test results relate to tests of the linear arrangement of wall panels in accordance with the requirements of EN 594 [1].
4
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
Prezentowane wyniki stanowią wstępne podsumowanie dotychczasowych badań własnych dotyczących połączeń zakładkowych, hybrydowych, nitowano-śrubowych. Rozważano elementy próbne z połączeniami dwuciętymi, w których jeden z nitów został wymieniony na śrubę wysokiej wytrzymałości. W poszczególnych elementach śruby osadzano w otworach zwykłych lub pasowanych, a następnie sprężano. Zagadnienie związane z wymianą nitów na śruby podjęto z uwagi na częste stosowanie takiej praktyki w przypadku remontów zabytkowych konstrukcji stalowych. Jednak nośność takich połączeń nie jest dotychczas potwierdzona badaniami modelowymi i analizami obliczeniowymi. Wyniki wykonanych badań zilustrowano na wykresach obciążenie - przemieszczenie, które można porównać z wynikami referencyjnymi dotyczącymi połączenia na dwa nity. Ponadto ustalono siłę niszczącą połączenia oraz oszacowano ich sztywność translacyjną. Ważnym etapem prowadzonych badań była analiza różnych układów łączników w połączeniu, a wnioski płynące z otrzymanych badań potwierdzają aktualny stan wiedzy zawarty w [1, 2].
EN
The results presented in this article are a preliminary summary of the authors’ research on the lap connections, hybrid joints, and riveted bolt joints. The analysed test elements with double-notched joints, in which one of the rivets was replaced with a high-resistance bolt. The bolts in specific elements were placed in regular or fitted holes and then pre-stressed. The issue related to the replacement of rivets with bolts was analysed due to the fact that this is a commonly used practice in the renovation of historic streel structures. However, the bearing capacity of those joints has not yet been confirmed by model studies with computational analyses. The results of the performed tests are presented in form of load-displacement diagrams, which may be compared to the reference results for double-riveted joints. A part from that, the joint breaking force was determined and the translational stiffness was assessed. An important element of the conducted research was the analysis of various arrangements of connectors in a joint. The results of the analyses confirm the current state of knowledge presented in publications [1, 2].
5
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
W pracy opisano przypadek stropu żelbetowego typu Filigran, dla którego przygotowano szereg opracowań opiniodawczych. Wynikało z nich, że strop kwalifikuje się do wzmocnienia przez usztywnienie, na skutek nadmiernych ugięć i drgań wpływających na komfort użytkowania. Wdrożono drogi i inwazyjny sposób wzmocnienia przez wymianę nadbetonu i wykonanie dodatkowych żeber. Jak się okazało, po dokładnych analizach dla pomierzonych i zbadanych charakterystyk, konstrukcja była bezpieczna. Jej nadmierne ugięcia były uchybieniem wykonawczym, a drgania dotyczyły jedynie warstw podłogowych i nie wynikały z tego, że konstrukcja nie ma wystarczającej sztywności.
EN
In the paper the case of the reinforced concrete ceiling of Filigran type was described, for which several consultative reports were prepared. According to them the ceiling was qualified for strengthening, by stiffening, as a result of excessive deflections and vibrations disturbing the comfort of exploitation. An expensive and invasive way of strengthening consisting of concrete topping replacement and additional ribs execution was implemented. As it was proved with a detailed analysis for measured and tested characteristics the structure was safe. Its excessive deflections was an execution fault. The vibrations involved only top floor layers and were not the consequence of the insufficient stiffness of the structure.
6
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
W słupach typu CFST w stanie granicznym dochodzi do zwiększenia wytrzymałości betonu rdzenia na skutek jego skrępowania. Zaistnienie tego zjawiska zależy od wielu czynników. Jednym z najważniejszych z nich jest sztywność obwodowa płaszcza stalowego. Jej wpływ na efektywność wzrostu wytrzymałości betonu rdzenia przebadano eksperymentalnie na grupie 48 grubościennych słupów CFST. Wykazano, że nadmierne zwiększanie grubości płaszcza słupa CFST nie przekłada się na wzrost jego nośności sprowadzonej. Jest wręcz przeciwnie: następuje jej spadek. Znacznie lepsze wykorzystanie pozytywnego wpływu skrępowania betonu rdzenia można osiągnąć z zastosowaniem rur cienkościennych niż grubościennych.
EN
In the limit state of the CFST columns, the core concrete strength increases due to its confinement. This positive effect depends on many factors. One of the most important is the ring stiffness of the steel tube. Its impact on the effectiveness of increasing the core concrete strength was experimentally tested on a group of 48 thick-walled CFST columns. It has been shown that an excessive increase in the tube thickness does not translate into an increase in its relative load capacity. On the contrary, it is decreasing. A much better use of the core concrete confinement can be achieved by using thin-walled tubes rather than thick-walled ones.
7
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
W artykule opisano badania ścian z autoklawizowanego betonu komórkowego (ABK) w skali naturalnej, w których zastosowano nowy typ zbrojenia z siatki stalowej. Omówiono wpływ zbrojenia na strefę połączenia ścian prostopadłych. Przeanalizowano nośność i rysoodporność połączenia. Wyniki porównano z wynikami badań wcześniejszych [1, 2]. Artykuł jest drugą częścią publikacji [3] oraz kontynuacją badań opisanych w [1, 2].
EN
The article describes the tests of walls made of autoclaved aerated concrete (AAC) on a full scale, in which the new type of steel mesh reinforcement was used. The influence of reinforcement on the connection zone of perpendicular walls was described. The load capacity and crack resistance of the connection zone were analysed. The results were compared with those of earlier studies [1, 2]. The article is the second part of the tests published in [3] and a continuation of earlier research [1, 2].
8
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
W artykule przedstawiono analizy numeryczne konstrukcji rusztowania z uszkodzeniami w postaci łukowego wygięcia stojaków. W przeprowadzonych obliczeniach analizowano wpływ lokalizacji i liczebności uszkodzeń, imperfekcji geometrycznych, normowych wariantów obciążenia oraz wysokości rusztowania na wielkość naprężeń normalnych. Celem przeprowadzonych analiz numerycznych jest zwiększenie poziomu wiedzy na temat wpływu uszkodzeń eksploatacyjnych na nośność głównych elementów konstrukcyjnych w rusztowaniach budowlanych.
EN
The paper presents numerical analyzes of the scaffolding structure with damages in the form of arc bending of the stands. In the calculations carried out, the influence of the location and number of damages, geometrical imperfections, standard load variants and scaffolding height on the value of normal stresses was analysed. The purpose of the conducted numerical analyzes is to increase the level of knowledge on the influence of operational damage on the load carrying capacity of the main structural elements in scaffolding.
W artykule podano metody wzmacniania wsporników słupów, których skuteczność została zweryfikowana badaniami eksperymentalnymi. Niezależnie od zastosowanej metody efektywność wzmocnienia wspornika jest głównie uzależniona od smukłości ścinania wspornika, ilości zbrojenia wewnętrznego i jego wytężenia przed wzmocnieniem.
EN
The article presents the methods of strengthening R-C corbels, the effectiveness of which has been verified by experimental research. Regardless of the method used, the effectiveness of the corbel strengthening is mainly dependent on the shear span to effective depth ratio, the amount of internal reinforcement and the effort of corbel before strengthening.
10
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
Zamieszczono zalecany w wytycznych ATV tok obliczeń nośności rur, który należy uznać za przybliżony. Następnie podano proponowany dokładniejszy tok obliczeń. Dokonano przeglądu zaleceń dotyczących ustalania współczynnika posadowienia, mającego bardzo istotny wpływ na nośność rur po ich wbudowaniu. Zamieszczono trzy przykłady różnych posadowień rur, wskazując jakie konsekwencje wynikają z bardziej niekorzystnego oraz bardziej korzystnego posadowienia rur, w stosunku do posadowień zalecanych przez projektanta.
EN
The method of calculating the load capacity of pipes recommended in the ATV guidelines is given. It is approximate. Then, the proposed exact method of calculations is given. The recommendations for determining the bedding coefficient, which have a very significant impact on the load capacity of pipes after their installation, have been reviewed. There are three examples of different pipe beddings indicating the consequences of more unfavorable and more favorable pipe beddings in relation to the recommended beddings.
Zagadnieniem omawianym w ramach artykułu jest innowacyjny system konsoli nośnych z przekładkami z tworzywa sztucznego. W ramach zleconych prac i grantów badawczych Koła Naukowego Konstrukcji Metalowych przeprowadzono badania konsoli poliamidowo-aluminiowych. Dostarczone wieszaki o różnych parametrach geometrycznych i materiałowych zostały przebadane w przestrzennej maszynie wytrzymałościowej znajdującej się na Wydziale Inżynierii Lądowej Politechniki Warszawskiej. Celem badań było określenie nośności konsoli na zginanie w płaszczyźnie, rozciąganie osiowe i wpływ zmęczenia. Następny krok obejmował przygotowanie analizy numerycznej w programie Abaqus CAE dla wybranego typu konsoli. Celem analizy MES było osiągnięcie końcowego stanu odkształcenia zgodnego z rzeczywistym, uzyskanym w ramach badań laboratoryjnych. W podsumowaniu przedstawiono wnioski wyciągnięte z porównania wyników uzyskanych w ramach badań laboratoryjnych i analizy numerycznej.
EN
The issue discussed in the article is an innovative system of support consoles with plastic spacers. As part of the commissioned works and research grants of the Koła Naukowego Konstrukcji Metalowych, tests of polyamide - aluminum consoles were carried out. Supplied hangers with different geometrical and material parameters were tested in a spatial testing machine located at the Faculty of Civil Engineering of the Warsaw University of Technology. The aim of the tests was to determine the bearing capacity of the console for in-plane bending, axial stretching and the effect of fatigue. The next step involved the preparation of a numerical analysis in the Abaqus CAE program for the selected type of console. The purpose of the FEM analysis was to achieve the final state of deformation consistent with the real one obtained during laboratory tests. The summary presents the conclusions drawn from the comparison of the results obtained as part of laboratory tests and numerical analysis.
The aim of the article was to determine the influence of shot peening of the outer surface of the overlap on the stress state in the adhesive layer and the load capacity of single lap adhesive joints made of EN AW-2024-T3 aluminum alloy. Experimental investigations and numerical simulations were carried out. According to the results of experimental analyses, shot peening with balls with a diameter of 1 mm for 120 s with a compressed air pressure of 0.5 MPa increased the load capacity of the adhesive joints by 33%. Numerical simulations have shown that shot peening, by deforming the joined elements, reduces the stress perpendicular to the surface of the adhesive layer which results in a reduction of equivalent (von Misses) stress and an increase in strength of adhesive joints.
PL
Celem artykułu było określenie wpływu pneumokulkowania zewnętrznej powierzchni zakładki na stan naprężeń w spoinie klejowej oraz nośność połączeń klejowych jednozakładkowych wykonanych ze stopu aluminium EN AW-2024-T3. W ramach badań przeprowadzono doświadczenia eksperymentalne i obliczenia numeryczne. Zgodnie z wynikami doświadczeń eksperymentalnych, pneumokulkowanie połączeń klejowych kulkami o średnicy 1 mm w czasie 120 s z ciśnieniem sprężonego powietrza wynoszącym 0,5 MPa przyczyniło się do wzrostu nośności połączeń klejowych o 33%. Obliczenia numeryczne wykazały, że pneumokulkowanie, poprzez odkształcenie klejonych elementów, zmniejsza naprężenia prostopadłe do powierzchni spoiny klejowej, co skutkuje zmniejszeniem jej wytężenia (naprężenień zredukowanych) i wzrostem wytrzymałości połączeń klejowych.
The aim of the work was to investigate the influence of selected shot peening parameters on the load capacity of adhesive joints and on the surface roughness of samples made of aluminum alloy 2024-T3. The research was also aimed at verifying whether it is possible to assess the load capacity of adhesive joints on the basis of the surface roughness parameters after shot peening. The treatment variants were developed according to the matrix of the Hartley's PS/DS-P:Ha3 plan. Shot peening time varied from 60 to 180 s, ball diameter from 0.5 to 1.5 mm and compressed air pressure from 0.3 to 0.5 MPa. As a result of the analysis of the correlation between the load capacity of connections and the surface roughness, it can be concluded that the greatest relationship exists between the load capacity and the Rku parameter. The regression analysis shows that the load capacity of the connections should increase along with the increase of the Rku parameter. The study also showed that the Rku parameter is also most strongly associated with the deflection of the Almen strips. The Almen strip deflection increases with the increase of the Rku parameter. The regression equation describing the influence of shot peening parameters on the value of the Rku parameter indicates that the value of the Rku parameter increases with the increase of the treatment time and the decrease of the ball diameter and the compressed air pressure.
PL
Celem pracy było zbadanie wpływu wybranych parametrów pneumokulkowania na nośność połączeń klejowych oraz chropowatość powierzchni próbek ze stopu aluminium 2024-T3. Badania miały również na celu sprawdzenie, czy możliwa jest ocena nośności połączeń klejowych na podstawie parametrów chropowatości powierzchni po pneumokulkowaniu. Warianty pneumokulkowania opracowano zgodnie z matrycą planu Hartleya PS/DS-P:Ha3. Czas obróbki zmieniał się w zakresie od 60 do 180 s, średnica kulek od 0,5 do 1,5 mm i ciśnienie sprężonego powietrza od 0,3 do 0,5 MPa. W wyniku analizy korelacji miedzy nośnością połączeń i chropowatością powierzchni można stwierdzić, ze największa zależność występuje pomiędzy nośnością a parametrem Rku. Analiza regresji wskazuje, ze wraz ze zwiększaniem wartości parametru Rku nośność połączeń również powinna wzrastać. W ramach pracy wykazano również, że parametr Rku jest parametrem chropowatości najsilniej związanym ze strzałką ugięcia płytek Almena. Strzałka ugięcia płytek Almena wzrasta wraz ze wzrostem parametru Rku. Równanie regresji opisujące wpływ parametrów pneumokulkowania na wartość parametru Rku wskazuje, że wartość parametru Rku wzrasta wraz ze zwiększaniem czasu kulkowania i zmniejszaniem średnicy kulek i ciśnienia sprężonego powietrza.
W pracy dokonano opisu badań laboratoryjnych i symulacji komputerowych przeprowadzonych na głównym elemencie konstrukcyjnym rusztowań ramowych. W rusztowaniach budowlanych głównymi elementami nośnymi są stojaki ram. W elementach tych podczas eksploatacji występuje największe wytężenie. Dlatego ewentualne uszkodzenia występujące w tych elementach powodują największe zagrożenie z punktu widzenia nośności konstrukcji. Badania laboratoryjne podzielono na dwie grupy. Pierwszą grupą badań jest obciążenie wycinka stojaka o długości 50 cm z uszkodzeniem w postaci punktowego wgięcia, osiową siłą ściskającą lub rozciągającą. Druga grupa badań laboratoryjnych została wykonana na całych ramach. W badaniach tych analizowano wpływ uszkodzenia w postaci łukowego wygięcia stojaka. Wszystkie przeprowadzone w laboratorium badania znalazły swoje odwzorowanie w modelach numerycznych.
EN
The paper describes laboratory tests and computer simulations carried out on the main structural element of frame scaffolding. In scaffolding, the main supporting elements are frame standards. The greatest strain occurs in these elements during operation. Therefore, possible damage in these elements causes the greatest threat from the point of view of the bearing capacity of the structure. Laboratory research was divided into two groups. The first group of tests was carried on a 50 cm long section of the standard pipe with damage in the form of a point bend. It was loaded with axial compressive or tensile force. The second group of laboratory tests was performed on the entire frame. In these studies, the impact of damage in the form of arc bending of the standard was analyzed. All the tests carried out in the laboratory were reproduced in numerical models.
Przedmiotem artykułu jest weryfikacja nośności stropu magazynu surowców o wymiarach 90,0×12,5 m wykonanego z kanałowych płyt strunobetonowych o wysokości 265 mm i modularnej szerokości 1,20 m. Po ułożeniu płyt kanałowych na ścianach zewnętrznych i wewnętrznych piwnicy oraz wykonaniu wieńców i złączy podłużnych między płytami zauważono, że w obliczeniach do projektu stropu uwzględniono obciążenia zmienne qk = 10 i 15 kN/m2, zapominając o siłach skupionych wywoływanych przez dwa wózki widłowe o udźwigu Qk = 20 kN każdy. Wstrzymano prace wykończeniowe stropu w celu opracowania sposobu przystosowania go do przenoszenia obciążeń wymienionych wyżej. W artykule przedstawiono analizy, wnioski i zalecenia dotyczące możliwości uzyskania żądanej przez inwestora nośności stropu z równoczesną eksploatacją wózków widłowych. Wyniki analiz wykorzystano do opracowania projektu wzmocnień konstrukcji stropu na ścinanie i zginanie poprzez zespolenie płyt z nadbetonem będącym posadzką magazynu oraz dodatkowo na ścinanie przez wypełnienie betonem części przypodporowej kanałów w płytach na długości obliczeniowej lpt2 = 0,90 m przekazywania siły sprężającej z cięgien na beton.
EN
The subject of the paper is verification of the load capacity of the floor of the raw material warehouse with dimensions of 90,0×12,5 m made of hollow-core prestressed concrete slabs 265 mm high and a modular width of 1,20 m. After placing the hollow-core slabs on the external and internal walls of the basement and making the tie beams and longitudinal joints between the slabs, it was noticed that in calculations for the detailed design of the floor with the live load qk = 10 and 15 kN/m2 no account was taken of the concentrated forces caused by two forklifts with a load capacity of Qk = 20 kN each. Finishing works of the ceiling were stopped in order to work out how to adapt it to transfer the loads mentioned above. The paper presents analyses, conclusions and recommendations concerning the possibility of obtaining the floor load capacity required by the investor with simultaneous use of forklifts. The results of the analysis has been used to strengthen the floor structure for shear and bending by joining the slabs with the 80 mm thick concrete topping. Additionally, higher shear capacity has been obtained by filling the supporting part of the channels (lpt2 = 0.90 m) with concrete at tendon transmission length.
W artykule przedstawiono wyniki wybranych badań laboratoryjnych certyfikowanych modułów (paneli) służących do wznoszenia budynków o drewnianej konstrukcji w autorskiej technologii Wood Core House (WCH). Rozwiązanie to może być stosowane zarówno do budowy nowych obiektów mieszkalnych czy użyteczności publicznej, jak również stosowane w modernizacjach, remontach lub nadbudowach budynków istniejących - z uwagi na ich mały ciężar. Rozwiązanie to łączy prefabrykację elementów z bezpośrednim montażem na budowie bez użycia ciężkiego sprzętu. Czyli umożliwia wykonanie konstrukcji drewnianej ścian tam, gdzie dojazd ciężkiego sprzętu jest utrudniony.
EN
This paper presents the results of selected laboratory tests of certified modules (panels) for the construction of timber-framed buildings using the author's Wood Core House (WCH) technology. This solution can be used both for the construction of new residential or public buildings, as well as applied in the modernisation, renovation or superstructure of existing buildings - due to their low weight. This solution combines prefabrication of the elements with direct assembly on site without the use of heavy equipment. This means that it is possible to build a wooden wall structure where access for heavy equipment is difficult.
Głównym celem pracy było wykonanie pionierskiej aplikacji wzmocnienia konstrukcji mostu przy użyciu naprężonych kompozytów CFRP z zastosowaniem tzw. „metody gradientowej” na konstrukcji mostu będącego w czynnej eksploatacji. Program badań własnych obejmował dwa dźwigary kablobetonowe o rozpiętości 18,0 m i wysokości przekroju 1,26 m. Dźwigary wykonane w laboratorium EMPA były dokładną kopią konstrukcji mostu wzmocnionego w 2015 w Szczercowskiej Wsi. Z dwóch elementów badawczych jeden zbadano jako referencyjny, a drugi wzmocniono na zginanie przy użyciu naprężonych taśm CFRP „metodą gradientową” oraz na ścinanie oplotami z mat CFRP. Dźwigary poddano badaniu nośności na zginanie oraz na ścinanie. Wyniki badań laboratoryjnych potwierdziły wysoką efektywność wzmocnienia dźwigarów kablobetonowych przy użyciu naprężonych taśm CFRP. Badania dźwigarów wykazały wzrost obciążenia rysującego o 16%, obciążenia niszczącego o 21% oraz ograniczenie maksymalnych ugięć o 19% w stosunku do dźwigara referencyjnego.
EN
The main objective of this work was to carry out a pioneering application of bridge structural strengthening using post-tensioned CFRP composites using the “gradient method” on a bridge structure in active use. The research program included two post-tensioned concrete girders with a clear span of 18,0 m and a section height of 1,26 m. The girders made in the EMPA laboratory were an exact copy of the bridge girders strengthened in Szczercowska Wies in 2015. From two test girders, the first was tested, as a reference, and the second was strengthened in bending using prestressed CFRP strips “gradient method” and in shear with braided CFRP sheets. The girders were tested for bending and shear capacity. The results of the laboratory tests indicated that the effectiveness of the strengthened post-tensioned concrete girders with prestressed CFRP strips using the “gradient method” was very high. The strengthened girder showed an increase of 16% in cracking load, 21% in ultimate load, and a reduction of maximum deflections by 19% compared to the reference girder.
18
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
Zbrojenie w konstrukcjach murowych stosuje się w celu ograniczenia zarysowań i zwiększenia nośności ścian. W artykule opisano badania ścian z autoklawizowanego betonu komórkowego (ABK) w skali naturalnej, w których zastosowano nowy typ zbrojenia z siatki stalowej. Określono wpływ zbrojenia na strefę wokół okna. Prezentowane badania są kontynuacją wcześniejszych podobnych analiz, opublikowanych w miesięczniku „Materiały Budowlane” [1, 2]. Uzyskane wyniki badań porównano z wynikami opublikowanymi w [1, 2, 3].
EN
Reinforcement in masonry structures is used to reduce cracks' width and increase the load-bearing capacity of walls. The article describes the study of autoclaved aerated concrete (AAC) walls in a full scale. A new type of steel mesh reinforcement was used in the tests. The influence of the reinforcement on the zone around the window was determined. The presented research is a continuation of previous similar analyzes published in Building Materials [1, 2]. The obtained tests results were compared with the results published in [1, 2, 3].
The paper is a continuation of the issue of the technical solution of a mast type jib crane for handling sludge pumps. It serves for the use in Building no. 900, Block V2, of the nuclear power plant Jaslovské Bohunice. It is an optimization of the original, in-service damaged handling device with manual control of lift and rotation. The overloading of the device has an insignificant effect on the lifting force on a crank handle. It was found that the lifting force permanently falls within the recommended range of 120 to 160 N for convenient operation by a single worker. Inasmuch as there is a complete absence of bearings in the slewing gear in the original design, it is the solution to this issue that is the subject of the paper. The problem of pulling out the sludge pumps, which was established in the course of using the jib crane, ingeniously provided the opportunities to further design changes on the original design. The solution offered was to scrap the original design of the carrier inserted into the support and replace it with a fixed mast on which the boom would rotate. Accordingly, it would potentially be feasible to increase the load capacity of the jib crane, and thus the issue of the sludge pumps attached to the tank bottom would be solved. Moreover, it is attainable to extend the scope of this crane in this way.
W artykule omówiono zastosowanie prętów kompozytowych z włókna szklanego jako alternatywnego sposobu zbrojenia elementów zginanych. Przedstawiono koncepcję zbrojenia minimalnego wyliczanego na podstawie układu sił w przekroju zginanym, a następnie porównano z wynikami badań. Wykazano, że w przypadku zbrojenia GFRP opieranie się jedynie na zależnościach statycznych może prowadzić do zaniżenia nośności.
EN
This paper presents the use of fiberglass composite bars as an alternative reinforcement method for flexural elements. The concept of the minimal reinforcement calculated from the balance of forces in the element is presented and then compared with test results. It is shown that when calculating the minimum degree of GFRP reinforcement, basing only on static relationships can result in too low a load capacity.
JavaScript jest wyłączony w Twojej przeglądarce internetowej. Włącz go, a następnie odśwież stronę, aby móc w pełni z niej korzystać.