Ionic liquids as anticorrosion agents have a wide spectrum of unique properties, which make them less harmful than the majority of typical organic corrosion inhibitors in antifreeze. The synthesis of ionic liquids enables them to be provided with the desired physicochemical and thermodynamical properties by the appropriate selection of cations, anions, and alkyl substituents on the cations. The aim of this paper is the synthesis of the gemini ionic salt (ionic liquid) made up of two imidazole rings with a linear alkyl substituent with 10 carbon atoms, bonded by a 1,4-dimethylphenyl moiety. Such compounds are studied in view of steel protection against oxidizing and corrosive effects. The compound was obtained in a satisfactory yield.
PL
Ciecze jonowe jako środki przeciwkorozyjne posiadają szereg unikalnych właściwości, które czynią je potencjalnie mniej szkodliwymi niż większość typowych organicznych inhibitorów korozji w płynach niskokrzepnących. Synteza cieczy jonowych daje możliwość nadawania im pożądanych właściwości fizykochemicznych i termodynamicznych poprzez odpowiedni dobór kationów, anionów i alkilowych podstawników przy kationach. Celem niniejszej pracy była synteza geminalnej soli jonowej (cieczy jonowej), zbudowanej z dwóch pierścieni imidazoliowych z prostołańcuchowym podstawnikiem alkilowym o 10 atomach węgla, połączonych ugrupowaniem 1,4-dimetylofenylowym. Związki tego typu są badane pod kątem ochrony stali przed działaniem utleniającym i korozyjnym. Związek otrzymano z zadowalającą wydajnością.
The pretreatment is a key step in the processing of lignocellulosic biomass for its transformation into chemicals and materials of biorenewable origin. Ionic liquids, with their characteristic set of unique properties, have the potential to be the basis of novel pretreatment processes with higher effectiveness and improved sustainability as compared to the current state-of-the-art processes. In this opinion paper, the author provides a perspective on possible processing strategies for this pretreatment with ionic liquids, identifying different advantages as well as challenges to be overcome.
Because of industrialization and modernization, phenomenal changes have taken place in almost all spheres of life. Consequently, the consumption of energy resources and the cases of environmental hazards have risen to an unprecedentedly high level. A development model with due consideration to nature and an efficient utilization of energy sources has become the need of the hour, in order to ensure a sustainable balance between the environmental and technological needs. Recent studies have identified the suitability of ionic liquids (ILs), often labeled as ‘green solvents’, in the efficient utilization of energy resources and activities such as bio-extraction, pollution control, CO2 capture, waste management etc. in an environmentally friendly manner. The advent of magnetic ionic liquids (MILs) and deep eutectic solvents (DESs) have opened possibilities for a circular economic approach in this filed. This review intends to analyze the environmental and energy wise consumption of a wide variety of ionic liquids and their potential towards future.
The paper presents results of investigations on the effect of the addition of graphene oxide (GO) on the structural properties of composite cellulose fibers (CEL). GO/CEL fibers were obtained from a solution of CEL in ionic liquid – 1-ethyl-3-methylimidazole acetate – with the addition of GO dispersion in DMF. A classic wet spinning method was used using water and methanol as coagulants. Results have shown that the addition of GO increases the crystallinity of fibers to 31–40.8%. Moreover, these results indicate a significant impact of the coagulant used in the fiber forming process. Methanol coagulated fibers have greater porosity and larger pore sizes than water coagulated fibers.
PL
Przedstawiono badania wpływu dodatku tlenku grafenu (GO) na właściwości strukturalne kompozytowych włókien celulozowych (CEL). Włókna GO/CEL otrzymywano z roztworu CEL w cieczy jonowej – octanie 1-etylo-3-metyloimidazolu – z dodatkiem dyspersji GO w DMF. Zastosowano klasyczną metodę formowania włókien na mokro z zastosowaniem wody oraz metanolu jako koagulantów. Badania wykazały, że dodatek GO wpływa na wzrost stopnia krystaliczności włókien do wartości 31–40,8%. Ponadto wyniki te wskazują na znaczny wpływ koagulantu stosowanego w procesie formowania włókien na ich strukturę. Włókna koagulowane metanolem mają większą porowatość i większe rozmiary porów niż włókna koagulowane wodą.
Chitin is the second most abundant polysaccharide on the Earth after cellulose, therefore there is a tangible need for finding new environmentally-friendly solvents for the manufacture of useful forms of that polymer. Ionic liquids have been recently proposed as a possible type of solvent for chitin and cellulose. The possibility of the dissolution of chitin of various origin in six selected ionic liquids was investigated. Chitin samples were characterised by the main characteristic properties: degree of N-acetylation (by FTIR spectroscopy), degree of crystallinity (by WAXS), average molecular weight (by the viscometric method) and physical form. The studies performed allowed to find the optimum chitin-ionic liquid system based on 1-btyl-3-methylimidazolium acetate for the manufacture of chitin fibres by the solution blow spinning method. Final products were characterized by the same set of parameters as the initial materials.
PL
Chityna jest drugim po celulozie polisacharydem na Ziemi, dlatego istnieje namacalna potrzeba znalezienia nowych i przyjaznych dla środowiska rozpuszczalników do produkcji użytecznych form tego polimeru. Niedawno ciecze jonowe zostały zaproponowane jako możliwe do zastosowania „zielone” rozpuszczalniki chityny i celulozy. W artykule oceniono możliwość rozpuszczania różnego pochodzenia chityny w sześciu wybranych cieczach jonowych. Próbki chityny zostały scharakteryzowane poprzez następujące właściwości: stopień N-acetylacji (spektroskopia FT IR), stopień krystaliczności (WAXS), średnia masa cząsteczkowa (metoda wiskometryczna). Przeprowadzone badania pozwoliły na znalezienie optymalnego systemu cieczy jonowej do wytworzenia włókien chitynowych metodą rozdmuchu. Produkty końcowe zostały scharakteryzowane poprzez ten sam zestaw parametrów, co początkowe polimery.
6
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
Results of the investigations on electrodepositon of zinc, copper and copper-zinc alloy coatings from the galvanic baths based on 2-hydroxyethyl- trimethylammonium acetate have been presented in the paper. An influence of cathodic current density on structure of the deposits (SEM) was determined. Moreover, a chemical composition (EDS) as well as a phase composition (XRD) of the obtained alloy coatings were analysed. On the basis of the realized studies it was found that the current conditions influence on grain size of zinc coatings, however in the case of Cu and Cu-Zn coatings the effect is unessential. The electrodeposited brass alloys were solid solutions of zinc in copper.
PL
W pracy przedstawiono wyniki badań nad elektroosadzaniem powłok cynkowych, miedzianych i stopowych Cu-Zn z kąpieli galwanicznych opartych na octanie 2-hydroksyetylo-(trimetylo)amoniowym. W ramach pracy określono wpływ katodowej gęstości prądu na strukturę osadzonej powłoki (SEM). Ponadto wykonano analizę składu chemicznego (EDS) oraz składu fazowego (XRD) wytworzonych powłok stopowych. Na podstawie przeprowadzonych badań stwierdzono, że warunki prądowe wpływają na rozmiar ziaren powłok cynkowych, jednakże w przypadku powłok Cu i Cu-Zn wpływ ten jest nieznaczny. Powłoki mosiężne osadzone elektrolitycznie stanowiły roztwór stały cynku w miedzi.
The absorption of 1-butyl-3-methylimidazolium chloride and acetate taken from commercial packaging was studied by means of UV-VIS and infrared spectroscopy with some differences observed. Further research showed that heating both 1-butyl-3-methylimidazolium chloride and acetate alone, as well as in the presence of wood pulp, causes the darkening of these ionic liquids. Changes in the colour of ionic liquids associated with a variation in the absorption characteristics of pure ionic liquids and wood solutions in these liquids in UV and visible light are expressed primarily in the widening of the absorption bands. The presence of coloured products formed during their heating, as well as dissolution of the chemical components of wood in ionic liquids, had relatively little effect on the position of individual absorption bands in the spectrum obtained by the FT-IR method. The small differences in the absorption of spruce groundwood solutions in ionic liquids in IR as compared to pure ionic liquids suggest that strong chromophore groups in ionic liquids are created without serious reconstruction of their structure.
PL
W pracy zbadano absorpcję chlorku i octanu 1-butylo-3-metyloimidazoliowego za pomocą spektroskopii UV-VIS i spektroskopii w podczerwieni (FT-IR), zaobserwowano pewne różnice. Dalsze badania wykazały, że zarówno ogrzewanie samego chlorku lub octanu 1-butylo-3-metyloimidazoliowego, jak i ogrzewanie cieczy jonowych, w których rozpuszczono ścier drewna świerkowego, powoduje ciemnienie tych cieczy jonowych. Zmiany barwy cieczy jonowych, związane ze zmianą charakterystyki absorpcji czystych cieczy jonowych i roztworów drewna w tych cieczach w świetle UV i widzialnym wyrażają się przede wszystkim w poszerzaniu pasm absorpcji. Obecność barwionych produktów ogrzewania badanych cieczy jonowych, jak również rozpuszczanie w nich chemicznych składników drewna, wywiera stosunkowo niski wpływ na położenie poszczególnych pasm absorpcji w widmie uzyskanym metodą FT-IR. Niewielkie różnice w widmach FT-IR cieczy jonowych, zawierających rozpuszczony ścier świerkowy w porównaniu z czystymi cieczami jonowymi, mogą wynikać z małego stężenia ścieru w tych cieczach jonowych.
This article reports the results of the study of an a-C:H:Si coating doped with silicon and produced by chemical deposition (PACVD). The effect of the coating on the tribological behaviour of IL-lubricated friction pairs was evaluated. The properties of the 100Cr6 steel specimens with and without the coating were compared. Scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) analysis were used for imaging the morphology of the coating surfaces and cross-sections and for identifying the elements in the coating composition. The contact angle of the investigated surfaces was measured with an optical tensiometer. Friction tests were performed on a ball-on-disc tribometer under dry friction and when lubricated with trihexyltetradecylphosphonium bis(trifluoromethylsulfonyl) amide ionic liquid. The geometrical structure of the surfaces before and after the tribological tests was measured using an optical profilometer. The ionic liquid used with the silicon-doped diamond-like coating under friction conditions reduced the coefficient of friction and wear. The results obtained from the tests and analysis allow for the conclusion that the use of DLC coatings a-C:H:Si lubricated with trihexyltetradecylphosphonium Bis(trifluoromethylsulfonyl) amide contributes towards the improvement of tribological properties of sliding surfaces under friction.
PL
Artykuł poświęcony jest badaniom powłoki diamentopodobnej domieszkowanej krzemem typu a-C:H:Si uzyskanej w procesie chemicznego osadzania z fazy gazowej wspomaganego plazmą PACVD. Ocenie poddano wpływ powłoki na właściwości tribologiczne węzłów tarcia smarowanych cieczą jonową (Ionic Liquid) IL. W analizie porównano próbki ze stali 100Cr6 bez powłoki oraz pokryte powłoką diamentopodobną. Przy użyciu skaningowego mikroskopu elektronowego SEM (Scanning Electron Microscopy) wyposażonego w mikroanalizator rentgenowski EDS (X-ray Energy Dispersive Spectroscopy), zobrazowano morfologię powierzchni powłok, ich przekroje poprzeczne oraz dokonano identyfikacji pierwiastków wchodzących w skład powłoki. Wykonano również pomiary kąta zwilżania badanych powierzchni na optycznym tensjometrze. Badania tarciowe przeprowadzono na tribotesterze pracującym w skojarzeniu trącym kula–tarcza w warunkach tarcia technicznie suchego oraz z zastosowaniem smarowania cieczą jonową triheksyltetradecylphosphonium bis(triffluoromethylsulfonyl) amide. Charakterystykę struktury geometrycznej próbek przed oraz po badaniach tribologicznych przeprowadzono na profilometrze optycznym. Wyniki badań wskazały, że użyta ciecz jonowa w skojarzeniu trącym z powłoką diamentopodobną domieszkowaną krzemem wpłynęła na zmniejszenie współczynnika tarcia oraz zużycia. Otrzymane wyniki wskazują, że zastosowanie powłok diamentopodobnych typu a-C:H:Si smarowanych triheksyltetradecylphosphonium bis(triffluoromethylsulfonyl) amidem sprzyja poprawie właściwości tribologicznych węzłów tarcia w ruchu ślizgowym.
Celem badań było uzyskanie kompozytów z kauczuku butadienowo-styrenowego (SBR) o polepszonych właściwościach użytkowych, obniżonej temperaturze i skróconym czasie wulkanizacji. Jako aktywator wulkanizacji zastosowano nanometryczny tlenek cynku zmodyfikowany cieczą jonową w masie elastomeru lub w rozpuszczalniku. Aplikacja takiego układu aktywującego pozwoliła uzyskać wulkanizaty o zwiększonej wytrzymałości na rozciąganie, twardości i odporności na starzenie termo-oksydacyjne w stosunku do zawierających mikrometryczny ZnO. Czas wulkanizacji uległ skróceniu, a temperatura i entalpia procesu zmniejszyły się. Uzyskano wulkanizaty o 50% mniejszej zawartości ZnO, zgodnie z Dyrektywą Unii Europejskiej.
EN
The main aim of research was to obtain elastomer composites of styrene-butadiene rubber (SBR) with improved functional properties, reduced temperature and time of vulcanization. Nanosized zinc oxide modified with ionic liquid directly in the elastomer matrix or in the solution process was used as vulcanization activator. Application of this activating system resulted in vulcanizates with increased tensile strength, hardness and resistance to thermo-oxidative aging as compared with microsized ZnO activator. The vulcanization time of SBR, the temperature and enthalpy of this process were reduced. The vulcanizates with 50% lower content of ZnO were obtained, according to the EU Directive.
New polyionens based on epoxy derivatives of 1,2-epoxy-4,7-dioxononen-8 and tetrahydro-1, 4-oxazine were synthesized. The basic regularities of polyionen synhthesis were established. Systematic study of the physico-chemical, optical, thermal and viscosimetric properties of new polyionens was carried out. It was found that the obtained polyionens are capable of operating in the range from -54 to 140°C. The ionic conductivity of synthesized polyionens are 10-2-10-4 Cm cm 2. Thus, the studied polyionens can be recommended for use as a component of liquid, polymeric lithium electrolytes, solar cells, condensers, as effective additives for cellulose triacetate compositions, as coagulants in the treatment of sewage.
11
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
This paper presents the results of studies on the preparation of cellulosic membranes, from a solution in 1-ethyl-3- methylimidazolium acetate (EMIMAc), using the phase inversion method. Initially, the membranes were obtained by coagulation of the polymer film in water and primary alcohols (methanol, ethanol, 1-propanol, 1-butanol, 1-pentanol), 1-hexanol, 1-octanol) resulting in membranes with significantly differing morphologies. Subsequently, composite membranes were produced, with the support layer being a membrane with the largest pores, and the skin layer a membrane with smaller pores. The resulting membranes were tested for physicochemical and transport properties. The morphology of the membrane surfaces and their cross-sections were investigated by using a scanning electron microscope (SEM). The structure of the membranes, on the other hand, was investigated by FTIR spectroscopy and WAXS structural analysis.
The purpose of the study was to evaluate the properties of DLC coatings with ionic liquids used as lubricants. The type a-C: H DLC coatings were deposited onto the 100Cr6 steel substrate by PVD. The surface topography of the DLC coatings was studied with a Bruker's Dimension Icon® Atomic Force Microscope (AFM), and surface morphology testing, cross section and chemical composition analyses were performed using the Jeol JSM-7100F scanning electron microscope, equipped with an EDS microanalyzer. Surface geometry measurements prior to and after tribological tests were performed on a Taylor Hobson's Talysurf CCI contactless optical profilometer. The tribological tests were carried out on an Anton Paar TRB tribotester under technically dry and lubricated friction with an ionic liquid, 1-Butyl-3-methylimidazolium tetrafluoroborate. The results show that DLC coatings and ionic liquids can significantly reduce resistance to motion.
PL
Celem przeprowadzonych badań była ocena właściwości powłok diamentopodobnych DLC smarowanych cieczami jonowymi. Powłoki diamentopodobne typu a-C:H naniesione zostały na stal 100Cr6 za pomocą metody PVD. Wykonano badania topografii powierzchni powłok DLC na mikroskopie sił atomowych AFM – Dimension Icon – Brucker oraz badania morfologii powierzchni, przekrojów poprzecznych oraz analizy składu chemicznego przy użyciu elektronowego mikroskopu skaningowego Jeol JSM –7100F, wyposażonego w mikroanalizator EDS. Pomiary struktury geometrycznej powierzchni przed i po testach tribologicznych wykonano na bezstykowym profilometrze optycznym Talysurf CCI Firmy Taylor Hobson. Testy tribologiczne przeprowadzono na tribotesterze Anton Paar TRB w warunkach tarcia technicznie suchego i tarcia ze smarowaniem cieczą jonową – tetrafluoroboranem 1-butylo-3-metyloimidazoliowym. Przedstawione wyniki badań wykazały, że zastosowanie powłok DLC oraz cieczy jonowej znacznie obniża opory ruchu.
Ionic liquids have attracted considerable interest as excellent alternatives to organic solvents to be used in homogeneous and biphasic processes. Ionic liquids are non-volatile, non-flammable and their “green” character has usually been justified with their negligible vapour pressure. However, the marketing of any chemical substance requires the determination of their impact on all elements of nature. Determination of the potential ecotoxicity of new chemical compounds is associated with conducting research on the effects of those compounds on the growth and development of selected organism. The phytotoxic properties of chiral ionic salts with the alkylimidazolium cation and the tetrafluoroborate anion were assessed for selected weeds popular in Poland: gallant soldier (Galinsoga parviflora Cav.), white goosefoot (Chenopodium album L.) and common sorrel (Rumex acetosa L.). It was found that 3-alkyl-1-[(1R,2S,5R)-(–)-menthoxymethyl]imidazolium tetrafluoroborates – ([C8-Im-Men][BF4]) and ([C9-Im-Men][BF4]) were low toxic to plants. A higher toxicity to terrestrial plants was characterized by ([C11-Im-Men][BF4]). The toxicity effect of compounds depended non only on the length of the alkyl chain in the function group but also on the concentration of the used compound and the type of plant which was sprayed with the tested compound.
14
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
Przedstawiono wyniki badań pochłaniania CO2 w cieczach jonowych [Emim][Ac] i [Bmim][Ac] pod ciśnieniem atmosferycznym, w kolumnie wypełnionej. W badaniach eksperymentalnych określono wpływ zawartości CO2 w gazie wlotowym i temperatury absorpcji na sprawność usuwania CO2 z gazu. Wyniki doświadczalne porównano z obliczeniami wykonanymi na podstawie zaprezentowanego modelu procesu. Badania pokazały, że pojemności sorpcyjne CO2 zastosowanych cieczy jonowych i roztworów amin są porównywalne, jednak w przypadku cieczy jonowych potrzebny jest znacznie dłuższy czas kontaktu (większa powierzchnia wymiany masy) do usunięcia tej samej ilości CO2.
EN
CO2 was absorbed from its mixt. with N2 in 1-ethyl – and 1-butyl-3-methylimidazilium acetates in a lab. Sprinkled column packed with Rashig rings. The applicability of both ionic liqs. for sepn. of CO2 from flue gases instead of NH2(CH2)2OH was confirmed.
15
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
W pracy przedstawiono wyniki badań wpływu dodatku wybranych cieczy jonowych do kąpieli stanowiącej roztwór wodorotlenku sodu na strukturę anodowo utlenianych powłok stopowych Zn-Co. Do badań wykorzystano cztery ciecze jonowe zbudowane z tego samego kationu 2-metylopirydyniowego i różnych anionów, tj.: octanowego, trifluorooctanowego, ortofosforanowego(V) i siarczanowego(VI). Do określenia struktury powstających powłok tlenkowych wykorzystano skaningową mikroskopię elektronową. W celu określenia składu chemicznego powierzchni zmodyfikowanej powłoki wykorzystano metodę spektroskopii fotoelektronów (XPS) oraz spektroskopię fluorescencji rentgenowskiej (XRF). Określono także odporność korozyjną metodą potencjodynamiczną (LSV). Na podstawie przeprowadzonych badań stwierdzono, że dodatek wszystkich zastosowanych cieczy jonowych powoduje powstawanie powłok tlenkowych bez widocznych pęknięć. Ponadto, powłoki te wykazują lepszą odporność korozyjną niż te, utlenianie w kąpieli bez dodatku cieczy jonowych.
EN
Results of investigations on effect of selected ionic liquids addition to the baths being solution of sodium hydroxide on a structure of anodically oxidized Zn-Co alloy coatings. Four ionic liquids consisted of the same 2-methylopyridinium cation and different anions, i.e.: acetate, trifluoroacetate, orthophosphate and sulfate were applied in the study. The X-ray photoelectron spectroscopy (XPS) and X-ray fluorescence spectroscopy (XRF) were used in order to determination of a chemical composition of the modified surface. A corrosion resistance by LSV potentiodynamic method was also determined. On the basis of the realized study it was found that the addition of ionic liquids results in formation the oxide coatings without cracks. Moreover, the coatings are characterized by better corrosion resistance that the ones oxidized in the bath without ionic liquid addition.
Praca obejmuje weryfikację i zastosowanie dotychczasowej wiedzy do otrzymania powłok aluminiowych na stali niskowęglowej, niskostopowej w procesie elektrolitycznym, w cieczy jonowej chlorku 1-etylo-3-metyloimidazolu, zawierającej chlorek glinu, AlCl3/[EMIm]Cl. Na podstawie pomiarów woltamperometrycznych przeprowadzonych z użyciem mikroelektrody z żelaza wyznaczono zakres potencjałów elektroredukcji anionu Al2Cl7–, który zweryfikowano w procesie elektroosadzania powłoki. Określono wpływ potencjału i gęstości prądu osadzania, temperatury i czasu na właściwości otrzymywanych powłok. Mierzalny efekt zmiany parametrów technologicznych na właściwości powłok występuje w temperaturze, w której zmiana lepkości cieczy jonowej ułatwia i przyspiesza proces elektroredukcji. W przypadku badanym jest to 50oC. Otrzymane powłoki charakteryzowały się strukturą mikrokrystaliczną i porównywalną odpornością korozyjną w porównaniu z właściwościami próbki aluminium technicznego.
EN
A verification of existing knowledge on an electrodeposition of the aluminium coating on low carbon steel carried out in ionic liquid is presented. An electroplating bath consists of ethyl-3-methylimidazolium chloride and aluminium chloride, AlCl3/[EMIm]Cl. The results of voltammetric (CV) measurements for iron microelectrode are used to determine the range of potentials of Al2Cl7– electroreduction. The values of potential range selected in CV measurements are verified in an electrodeposition process of a coating. The impact of potential and current density, temperature and time on the properties of the coatings is evaluated. Detectable effect of changes of processing current densities is observed at the temperature of significant decrease of a ionic liquid viscosity. In this study it is 50oC. The coatings obtained exhibit a microcrystalline structure and similar corrosion resistance in comparison with solid Al of technical quality.
Praca prezentuje zastosowanie układu mikrokanałów do konstrukcji przepływowego wiskozymetru o zminimalizowanych wymaganiach dotyczących objętości badanej próbki. Istotą jego działania jest obserwacja granicy kontaktu strumieni cieczy badanej i referencyjnej w mikrokanale i odniesienie jej pozycji do stosunków lepkości tych cieczy. Otrzymane wyniki pomiarów tak przebadanej cieczy jonowej zostały potwierdzone techniką pasywnej mikroreologii optycznej wskazując na możliwość wykorzystania obydwu technik do pomiarów, w których minimalizacja objętości próbki ma kluczowe znaczenie.
EN
The application of microchannel-based flow-through viscometer characterized by minimized sample volume requirements is presented in the paper. The measurement was performed by the observation of laminar fluid-fluid interphase between two liquids and relating its position to viscosity ratio of both liquids. The obtained results were cross-checked with the passive optical rheometry showing a possibility of using these two techniques in case when a small sample volume is crucial.
Zbadano wpływ dodatku prekursorów czwartorzędowych amoniowych cieczy jonowych o podstawnikach alkilowych na nadpotencjał wydzielania tlenu i wodoru na elektrodach z węgla szklistego i platyny. Badane prekursory cieczy jonowych różniły się długością jednego z podstawników alkilowych. Znaleziono optymalną długość podstawnika, zapewniającą znaczne zwiększenie nadpotencjału wydzielania gazów. Sprawdzono również, jak zmiana anionu z wodorosiarczanowego (VI) na siarczanowy (VI) wpływa na właściwości tych cieczy. Wykazano, że prekursory cieczy jonowych z anionem siarczanowym (VI) posiadają gorsze właściwości pod względem rozszerzenia przedziału trwałości potencjałowej wody w stosunku do analogów z anionem wodorosiarczanowym (VI).
EN
Influence of addition of precursors of quaternary ammonium ionic liquids on overpotential of oxygen and hydrogen evolution reactions was examined on glassy carbon and platinum electrodes. Ionic liquids differ in length of one of the alkyl chains. Optimal length of alkyl chain, which ensures high increase of gas evolution reaction overpotential was found. Influence of anion change, from bisulphate (VI) to sulphate (VI), was also verified. It was concluded that ionic liquids with sulphate (VI) anions has lower ability to enhance electrochemical stability window of water than ionic liquids with bisulphate (VI) ones.
Celem opisywanych badań była ocena wpływu cieczy jonowej należącej do grupy czwartorzędowych soli amoniowych, na właściwości biobójcze nanowłókien z polimeru PLA [poli(kwas mlekowy)] oraz PHB [poli(3-hydroksymaślan)]. Nanowłókna w postaci włókniny wytworzono za pomocą elektroprzędzenia z roztworu. Oba zaproponowane polimery termoplastyczne są nietoksyczne, biodegradowalne oraz biokompatybilne, ale nie wykazują aktywności biologicznej. Właściwość tę zaplanowano nadać nanowłóknom wykorzystując w tym celu ciecz jonową – azotan didecylodimetyloamoniowy [DDA][NO3], którą wprowadzono do roztworów poszczególnych polimerów przed procesem elektroprzędzenia. Przeanalizowano wpływ dodatku czwartorzędowej soli, zarówno na przebieg procesu elektroprzędzenia jak i na właściwości otrzymanych nanowłókien. Wykonano ocenę podatności otrzymanych nanowłókien na działanie grzybów pleśniowych poprzez ocenę stopnia wzrostu mikroorganizmów na badanych próbkach. Otrzymane nanowłókna poddano również ocenie mikroskopowej pod kątem ewentualnych zmian w strukturze włókien elementarnych z wykorzystaniem skaningowego mikroskopu elektronowego (SEM). Zbadano też parametry termiczne modyfikowanych nanowłókien, wyznaczając szybkość wydzielania ciepła w zależności od temperatury za pomocą mikrokalorymetru (PCFC), oraz oceniono możliwości zastosowania otrzymanych nanowłókien w procesie filtracji, wyznaczając parametry efektywności filtracji, spadku ciśnienia oraz współczynnik jakości otrzymanych filtrów.
EN
The aim of this study was to evaluate the effect of the ionic liquid belongs to quaternary ammonium salts on biocidal properties of PLA [poly(lactid acid)] and PHB [poly(3-hydroxybutyrate)] nanofibres. Nanofibres in non-woven form were prepared by electrospinning process. Both of these polyesters are non-toxic, biodegradable and biocompatible thermoplastics with high potential applications but they do not possess their own biological activity. The study was included the achievement of this activity by incorporating substances with antimicrobial properties. For this purpose the ionic liquid was selected. Didecyldimethylammonium nitrate [DDA][NO3] was added to the electrospinning solution of several polymers before electrospinning process. The influence of the quaternary salt addition on the course of electrospinning process and the nanofibres properties were observed. The evaluation of susceptibility of obtained nanofibres to mould fungi was made by assessing the degree of microbial growth on the samples surface. The morphology of the obtained nanofibres was characterized by scanning electron microscopy (SEM) to evaluate the nanofibre structure. The thermal parameters of modified nanofibers were also studied, setting the heat release rate depending on the temperature using microcalorimeter (PCFC). Also evaluated the applicability of the obtained nanofiber in the filtration process, setting the parameters of the filtration efficiency, pressure drop and the quality factor of the obtained filters.
Nowoczesne techniki ekstrakcyjne, w których tradycyjne rozpuszczalniki organiczne oraz pokrycia włókien zastąpiono cieczami jonowymi, stanowią doskonałe potencjalne rozwiązanie na etapie przygotowania próbek do analizy.
JavaScript jest wyłączony w Twojej przeglądarce internetowej. Włącz go, a następnie odśwież stronę, aby móc w pełni z niej korzystać.