Ograniczanie wyników
Czasopisma help
Autorzy help
Lata help
Preferencje help
Widoczny [Schowaj] Abstrakt
Liczba wyników

Znaleziono wyników: 55

Liczba wyników na stronie
first rewind previous Strona / 3 next fast forward last
Wyniki wyszukiwania
Wyszukiwano:
w słowach kluczowych:  bonding
help Sortuj według:

help Ogranicz wyniki do:
first rewind previous Strona / 3 next fast forward last
1
Content available remote Bonding methods of ceramic materials with deposited carbon layers
EN
In this paper, we present a proposed bonding technology of ceramic materials. It could be applied for manufacturing the excitation source for detection of elements by means of Optical Emission Spectroscopy (OES) method. The biggest challenge was choice of proper bonding technology for materials with screen printed carbon layers as an excitation electrodes. It was caused by a need to avoid a deterioration of electrical properties of the carbon layer during the bonding process. The bonding at low temperature with various glaze layers was verified with addition of noble elements and plasma modification. The results were promising, without any significant destruction of carbon layers.
PL
W tym artykule przedstawiamy proponowaną technologię łączenia materiałów ceramicznych która może być zastosowana przy wytwarzaniu źródła wzbudzenia do detekcji pierwiastków w metodzie optycznej spektroskopii emisyjnej. Wybór odpowiedniej technologii łączenia materiału z warstwami węglowymi wytwarzanymi metodą sitodruku był wyzwaniem z powodu konieczności uniknięcia degradacji właściwości elektrycznych węgla podczas procesu łączenia. Zweryfikowano łączenie w niskiej temperaturze z różnymi warstwami szkliwa z dodatkiem pierwiastków szlachetnych i modyfikacją plazmową. Wyniki były obiecujące, bez znacznego zniszczenia warstw węglowych.
PL
Artykuł przedstawia wyniki badań laboratoryjnych przyczepności zaczynów cementowych do trzech formacji skalnych, tj. rdzeni powstałych z piaskowca, mułowca oraz węgla kamiennego. Przygotowane rdzenie skalne (przed zalaniem zaczynem cementowym) poddawane były procesowi przemywania w różnych cieczach (prowadzono też badania dla tzw. rdzeni suchych). Do badań przyczepności wytypowano recepturę zaczynu cementowego zawierającą 1% nanotlenku glinu (n-Al2O3) oraz recepturę konwencjonalną (porównawczą, tj. bez udziału nanokomponentu). Badane zaczyny cementowe miały dobre parametry technologiczne, umożliwiające ich zastosowanie do uszczelniania kolumn rur okładzinowych w otworach wiertniczych o temperaturze dynamicznej około 35°C oraz ciśnieniu około 15 MPa. Po wykonaniu szeregu badań laboratoryjnych stwierdzono, że zaczyn zawierający dodatek 1% n-Al2O3 w wyraźny sposób podnosił przyczepność kamienia cementowego do formacji skalnej. Uzyskane wartości przyczepności dla zaczynu z n-Al2O3 w porównaniu z wartościami otrzymanymi dla zaczynu konwencjonalnego są około 30–40% wyższe. Analizując przyczepność kamienia cementowego (z dodatkiem i bez dodatku nanokomponentu) do różnego rodzaju formacji skalnych, należy zaznaczyć, że: najwyższą przyczepność zanotowano w przypadku piaskowca, nieco niższą – mułowca (około 80–85% wartości przyczepności uzyskanej dla piaskowca), a najniższą – węgla (około 70–75% wartości przyczepności uzyskanej dla piaskowca). Zależność ta zachodzi w podobny sposób w przypadku rdzeni „suchych”, jak i przemytych płuczką, buforem oraz cieczą przemywającą. Należy podkreślić niezwykle istotną rolę odpowiedniego procesu przemywania otworu wiertniczego przed wykonaniem zabiegu cementowania rur okładzinowych. Zastosowanie samego buforu może okazać się niewystarczające. Dodatkowe użycie odpowiednio dobranej cieczy przemywającej pozwala skutecznie usunąć resztki osadu filtracyjnego pozostającego na powierzchni formacji skalnej po jej przewierceniu, co powinno znacznie poprawić stan zacementowania otworu wiertniczego.
EN
The article presents the results of laboratory tests of adhesion of cement slurries to three rock formations, i.e. sandstone, mudstone and hard coal cores. The prepared rock cores (before being poured over with cement slurry) were washed in various fluids (tests were also conducted for the so-called “dry” cores). The adhesion tests were carried out for two selected cement slurries recipes: cement slurry containing 1% aluminum nanoxide (n-Al2O3) and conventional cement slurry (comparative, i.e. without the addition of nanocomponents). The tested cement slurries had good technological parameters, enabling their use for sealing casing columns in boreholes with a dynamic temperature of approx. 35°C and a pressure of approx. 15 MPa. After a series of laboratory tests, it was found that the slurry containing the addition of 1% n-Al2O3 significantly increased the adhesion of the cement stone to the rock formation. The obtained values of adhesion for the n-Al2O3 slurry, compared to the values obtained for the conventional slurry, are about 30–40% higher. When analyzing the results of adhesion of cement stone (with and without the addition of a nanocomponent) to various types of rock formations, it is stated that the highest values of adhesion was obtained for sandstone, slightly lower for mudstone (about 80–85% of the adhesion value obtained for sandstone) and the lowest for coal (about 70–75% of the adhesion value obtained for sandstone). This dependence is similar in the case of “dry” cores and those washed with mud, spacer fluid and washing fluid. It should be emphasized that the proper process of washing the borehole is very important prior to cementing the casing. The use of a spacer fluid alone may not be sufficient. The additional use of a properly selected washing liquid increases the mud-cake removal efficiency, which should significantly improve the quality of borehole cementing.
EN
Moisture influence on solid wood bonded with modified starch. A growing and developing population is contributing to the ever-increasing global warming, which is caused, among other things, by the heavy use of chemicals. Most of them are crude oil-based, which is a non-renewable source. That is why the population tries to find organic substitutes in every area, even in the wood industry. Here, the most common and popular binders - amine resins, are subjected in research to partial or full replacement by more natural binders, non-formaldehyde, made of renewable raw materials, preferably plant-based. In this project, the studies were carried out on the possibility of starch-based glue application in wood bonding and its effect on glued birch wood (Betula pendula Roth) under various environmental storage conditions of bonded samples (0%, 65%, and 100% of RH). The results show, that the samples at room temperature and normal humidity, as well as another – additionally dried, have a very similar shear strength. In-wood damages, on the other hand, are much more varied. The research also included moistened samples, which gave poorer results (about 12% lower than the remaining samples). Based on the results, it can be concluded, that modified starch is a very good organic glue, that can potentially replace some chemical products in certain applications.
PL
Wpływ wilgoci na drewno lite sklejone skrobią modyfikowaną. Przeprowadzono badania nad możliwością zastosowania kleju skrobiowego w spajaniu drewna i jego wpływem na klejone drewno brzozowe (Betula pendula Roth) w różnych warunkach środowiskowych przechowywania sklejonych próbek. Wyniki pokazują, że próbki w temperaturze pokojowej i normalnej wilgotności, a także inne – dodatkowo wysuszone, mają bardzo zbliżoną wytrzymałość na ścinanie. Z drugiej strony uszkodzenia drewna są znacznie bardziej zróżnicowane. Badaniami objęto również próbki nawilżane, co dało gorsze wyniki. Na podstawie uzyskanych wyników można stwierdzić, że skrobia modyfikowana jest bardzo dobrym klejem organicznym, który potencjalnie może zastąpić niektóre produkty chemiczne w szczególnych zastosowaniach.
PL
Elewacje z okładzinami kamiennymi przyklejanymi do ścian niewątpliwie należą do grupy najstarszych systemów wykończenia ścian zewnętrznych. Na systemy te składają się: okładziny kamienne, łączniki mechaniczne i zaprawy klejowe. Systemy te były często stosowane w Polsce na budynkach reprezentacyjnych w minionych epokach, często objętych opieką konserwatorów zabytków. Niestety czas, oddziaływania środowiskowe i antropogeniczne niekorzystnie wpływają na tego typu elewacje. Awarie omawianych systemów (ze względu na masę okładzin kamiennych) mogą powodować bardzo groźne skutki. Główne przyczyny awarii tych typów elewacji związane są z zaniedbaniami użytkowymi. Zminimalizowanie ryzyka wystąpienia awarii jest możliwe dzięki systematycznemu przeprowadzaniu okresowych ocen stanu technicznego tych elewacji. W artykule przedstawiono zasady przeprowadzania ocen elewacji z okładzin kamiennych oraz podstawowe zakresy czynności pozwalających określić ich stan techniczny. Opisano również metody eksperckie i badawcze pozwalające na diagnozowanie omawianych systemów elewacyjnych z wymaganymi dokładnościami.
EN
The system consists of: stone cladding, mechanical fasteners, adhesive mortars. These systems were often used in Poland on representative buildings from bygone eras, often under the care of the conservator. Unfortunately, time, environmental and anthropogenic impacts adversely affect this type of elevation. Failures of the discussed systems (due to the mass of stone cladding) can have very serious consequences. The main cause of failure of this type of systems is related to negligence in use. Minimizing the risk of failure is possible thanks to systematic periodic assessments of these building facades. The paper presents the principles of periodic assessments of stone facades and the basic scope of activities allowing to determine their technical condition. Also, expert methods are described which allow to diagnose the discussed facade systems with the required accuracy.
PL
W artykule przedstawiono nową technikę wznoszenia murów z wykorzystaniem kleju murarskiego poliuretanowego. Opisano zalety tej techniki wznoszenia murów na przykładzie realizowanych budynków mieszkalnych.
EN
The article presents a new technique of erecting walls using polyurethane masonry glue. The advantages of this wall construction technique are described on the example of implemented residential buildings.
EN
Aircraft composite structures made in autoclave prepreg technology are characterized by low porosity and high strength. Unfortunately, composite structures are susceptible to impact damage. Therefore in order to repair this type of structures, an advantageous method of structure restoration is the use of the two-step bonding method. This method relies on creating a composite patch cured in an autoclave and then bonding it into a previously prepared repair area in the repaired structure, created by removing the damaged layers. Thanks to this approach, the patch is produced in accordance with the production process of the repaired element and has similar properties including low porosity. A critical element of repair is the bonding layer between the patch and repaired structure. Difficulties in obtaining an appropriate consolidation pressure (compression) using a vacuum bag can cause local disbonding of the composite patch as well as porosity in the bonding layer. Porosity reduces the strength properties of the joint, and it also reduces its weather resistance, which may contribute to its gradual degradation. The article focuses on analysis of the influence of compression obtained by a vacuum bag on the porosity and thickness of the bonding layer. A professional line for the production of aircraft composites and a mobile system for composite repairs of aircraft structures were used to produce the samples. The computed tomography method was used to measure the porosity and thickness of the bonding layer.
EN
Bonding of sawmill birch wood with selected biopolymer-based glues. The aim of the research was to determine the shear strength and in-wood damage share of birch lamellas with the surface shaped by rotary saw cutting and bonded with the use of selected biopolymers, such as gelatine, caseine, gluten and polyvinyl acetate (PVAc), as a reference bonding material. The results show that the highest shear strength was achieved in case of PVAc glue used as a binder. From the tested group of biopolymers, a gelatine/acetic acid mixture gave the highest strength.
8
Content available remote Adhesive mixing and applying device
EN
The aim of the present article is to present the design concept of a specialized device for mixing and applying adhesives (one and two-component ones) intended for unit production or laboratory use. The paper presents the initial assumptions of the device design, such as the type of production, application method and adhesive properties. Technological requirements for the adhesive mixing and applying device were enumerated. The technological requirements will include the characteristics of the method of adhesive application. The construction requirements of the designed device are also presented. The design of this device has been presented in the form of a 3D model, made with use of the SolidEdge software. The advantages and limitations of the concept of the designed device were also presented.
PL
Celem niniejszej pracy jest przedstawienie koncepcji projektu specjalizowanego urządzenia do mieszania i nakładania klejów (jedno- i dwuskładnikowych), przeznaczonego do produkcji jednostkowej lub do zastosowań laboratoryjnych. W pracy przedstawiono założenia wstępne projektu urządzenia, takie jak: rodzaj produkcji, sposób nakładania oraz właściwości kleju. Przedstawione zostaną także wymagania technologiczne stawiane urządzeniu do mieszania i nakładania kleju. Wśród wymagań technologicznych wymienia się m.in. sposób nakładania kleju. Przedstawiono także założenia konstrukcyjne zaprojektowanego urządzenia klejarskiego. Projekt tego urządzenia został przedstawiony w formie modelu 3D, wykonanego za pomocą programu SolidEdge. Zaprezentowano także zalety oraz ograniczenia koncepcji zaprojektowanego urządzenia.
EN
The fatigue test was carried out on an element of a rotor blade removed from the Mi-2 helicopter. The purpose of the test was to check the fatigue strength of the repaired rotor blade. Metal composite rotor blades have a metal spar in the form of a box and the trailing sections in the form of metallic honeycomb sandwich panels. The trailing sections are bonded to the spar. The repair had been carried out at the point where the trailing section became debonded from the spar at the Air Force Institute of Technology in Warsaw using a methodology developed for carrying out repairs of rotor blades’ damage. All types of the Mi family helicopters are equipped with metal composite rotors blades. Depending on MTOW (Maximum Take-Off Weight) and destination of helicopters, blades differ in dimensions, but their design solutions are practically the same. For this reason, the developed repair methodology can be used for all characteristic rotor blades structures for Mi helicopters. The fatigue test was performed at the Łukasiewicz - Institute of Aviation in Warsaw, using a hydraulically driven fatigue machine. The fatigue test was carried out by performing over 1.1 million load cycles. In repair places, upon completion of fatigue testing, no damage was found.
EN
Bonding of birch solid wood of sawmill surface roughness with use of selected thermoplastic biopolymers. The aim of the research was to determine the shear strength and in-wood damage share of the birch lamellas of the surface shaped by rotary saw cutting and bonded with use of selected thermoplastic biopolymers, like polylactide (PLA) and polycaprolactone (PCL), as well as with use of polypropylene (PP) as a reference bonding material. The results show that the highest mechanical properties have been achieved in case of PLA used as a binder.
PL
Łączenie drewna brzozy o chropowatości drewna tartacznego z wykorzystaniem wybranych biopolimerów termoplastycznych. Celem badań było określenie wytrzymałości na ścinanie i udziału zniszczenia w drewnie lameli brzozowych o powierzchniach ukształtowanych na pilarce tarczowej i sklejonych przy użyciu wybranych biopolimerów termoplastycznych, takich jak polilaktyd (PLA) i polikaprolakton (PCL), jak również z zastosowaniem polipropylenu (PP) jako referencyjnego materiału wiążącego. Badania wykazały najwyższą przydatność PLA do łączenia litego drewna brzozy, podczas gdy pozostałe wykorzystane w badaniach polimery dawały spoinę o niższych od wspomnianego polimeru wytrzymałości.
11
PL
Wprowadzanie materiałów nowej generacji o podwyższonych właściwościach mechanicznych i eksploatacyjnych zwiększa niezawodność środków transportu wodnego, a tym samym bezpieczeństwo żeglugi i obniża koszty eksploatacyjne. Do tej grupy należą odlewane metalowe materiały kompozytowe. Brak jest jednak ciągle precyzyjnego i szybkiego opisu metody łączenia tych tworzyw, co znacznie utrudnia ich wykorzystanie. Dlatego trwają pracę nad doborem dobrych jakościowo metod ich spajania. W niniejszej pracy podjęto próbę łączenia odlewanych kompozytów typu AlSi/SiC przez spawanie metodą TIG prądem stałym.
EN
The introduction of new generation materials with improved mechanical and operational properties increases the reliability of water transport means, thus the safety of shipping, and reduces operating costs. This group includes cast metal composite materials. However, there is still no precise and quick description of the method of combining these materials, which siqnificantly hampers their use. Therefore, work is ongoing on the selection of good quality methods of their bonding. In this work, an attempt was made to join cast AlSi/SiC composites by TIG welding using direct current.
PL
Artykuł poświęcony jest metodyce oraz wdrożeniu produkcji obudowy lusterka samochodowego, wykonanej jako połączenie klejone części wierzchniej z kompozytu węglowego na bazie żywicy epoksydowej oraz insertu z materiału ABS mającego na celu umożliwienie połączenia obudowy z bazą lusterka. Podstawą opracowania były testy rzeczywiste oraz symulacje numeryczne przygotowane w oprogramowaniu Moldex3D. Zastosowane połączenie klejone obydwu komponentów nie zapewniło odpowiednich własności eksploatacyjnych, w wyniku czego dochodziło do pęknięć. Po przeprowadzeniu symulacji numerycznych ustalono, że miejsca pęknięć odpowiadają miejscom łączeń frontów płynącego tworzywa podczas wtrysku. Przyczyną pękania okazała się duża różnica rozszerzalności cieplnej obydwu materiałów. W efekcie powstawały znaczące naprężenia, które niszczyły insert ABS w najsłabszych miejscach. Problem skutecznie rozwiązano dzięki zmianie geometrii insertu.
EN
The aim of this study was to elaborate on the methods of constructing combined components of a car mirror. The components were made of materials with different thermal expansion coefficient. The basis for the research were numerical simulations prepared in Moldex 3D software. The external cover of a mirror would be made of carbon composite based on epoxy resin (hereafter referred to as carbon), and the internal insert would be made of ABS. The adhesive bonding applied did not provide appropriate properties and led to breaks during usage. After carrying out moldflows it was found that the areas of breaks were determined by the places where fronts of flowing material met during the injection. The cause of breaking was diametrically different thermal expansion of both materials. This induced significant stresses in adhesive layer. Finally, an effective solution was to change the geometry of the mirror insert made of thermoplastic ABS.
EN
Bonding technology is one of the oldest technologies of joining car body elements. Bonding steel in real industrial conditions may cause various incompatibilities in the joints area. The main ones consist in the lack of adhesion and no adhesive in the area of the joints. Currently there are destructive methods of controlling adhesive joints that require destruction of the joint. Destruction of joint generates significant costs especially when assessing joints in commercial vehicles. However assessment on vehicles being repaired or operated is not possible, because it causes total destruction of the joint. As a part of the work it was decided to check whether the ultrasound echo technique would enable locating these areas in the vehicle body in which there is no adhesives or lack of adhesion occurs - not only on prepared samples but also on the element - the door of a currently produced car vehicle. The ultrasonic measurements were verified during the destructive control of adhesive joint in the doors of a motor vehicle. The tests confirmed that the proposed measures of quality enable the location of the adhesive path between the two body shells.
PL
Technologia klejenia jest jedną z najstarszych technologii łączenia elementów karoserii pojazdów samochodowych. Klejenie stali w rzeczywistych warunkach przemysłowych może powodować różne niezgodności w obszarze połączenia. Główne z nich to deadhezja oraz brak kleju w obszarze założonego połączenia. Obecnie funkcjonują niszczące metody kontroli połączeń klejowych, które wymagają zniszczenia połączenia. Zniszczenie połączeń generuje znaczne koszty, szczególnie w przypadku oceny połączeń w pojazdach dostawczych. Nie umożliwiają one jednak oceny na pojazdach naprawianych lub eksploatowanych, ponieważ powodują całkowite zniszczenie połączenia. W ramach realizowanych prac postanowiono sprawdzić czy ultradźwiękowa technika echa umożliwi zlokalizowanie tych obszarów w karoserii, w których brakuje kleju lub nastąpiła deadhezja – nie tylko na spreparowanych próbkach, ale również na elemencie rzeczywistym – drzwiach współcześnie produkowanego pojazdu samochodowego. Wykonane prace zostały zweryfikowane w czasie kontroli niszczącej połączeń klejowych w drzwiach współczesnego pojazdu samochodowego. Przeprowadzone badania potwierdziły, że zaproponowane miary jakości umożliwiają lokalizację ścieżki kleju między dwiema blachami karoseryjnymi.
EN
Thermoplastic olefins (TPO’s) are important materials for the manufacture of exterior and interior automotive components due to their low cost, reduced specific density in comparison with other types of plastics, easy processing, and 100% recyclability. Nano-composites with TPO matrix additionally offer significant gains in strength and impact resistance due to excellent interfacial reinforcement effect, a high modulus of elasticity, and the matrix ductility. Typical automotive products made of standard TPO’s and PP-based nanocomposites include: bumper bars, protective bodyside mouldings, exterior and interior cladding, e.g., door trim panels, instrument panels, gearbox console and seat structure components. One of key drawbacks of TPO’s is their chemical inertness. This necessitates priming or appropriate surface treatment to enable the assembly of products through adhesive bonding and to facilitate adequate adhesion of paints, sealants, or other functional and decorative materials. Considering the above, the objective of this paper is two-fold: (1) To investigate and assess a range of processes for enhancing adhesion of TPO’s, e.g., flame treatment, chlorinated polyolefin (CPO) primers and a proprietary surface engineering process (SICORä) of TPO’s and other plastics and assess their suitability for a range of applications in automotive products, and (2) To demonstrate practical examples of the use of SICORä process for adhesion control in the automotive industry.
PL
Termoplastyczne olefiny (TPO) są ważnymi materiałami do produkcji zewnętrznych i wewnętrznych części samochodowych ze względu na ich niski koszt, zmniejszoną gęstość właściwą w porównaniu z innymi rodzajami tworzyw sztucznych, łatwą obróbkę i niemal 100% możliwość recyklingu. Nanokompozyty z matrycą TPO dodatkowo oferują znaczny wzrost wytrzymałości i odporności na uderzenia dzięki doskonałemu oddziaływaniu wzmacniającemu międzyfazowy efekt, wysokiemu modułowi sprężystości i plastyczności matrycy. Typowe produkty motoryzacyjne wykonane ze standardowych nanokompozytów na bazie TPO i PP obejmują: zderzaki, listwy ochronne, zewnętrzne panele karoserii i panele wewnętrzne, np. panele drzwi, deski rozdzielcze, konsole skrzyni biegów i elementy konstrukcji siedzenia. Jedną z głównych wad TPO jest ich obojętność chemiczna. Wymaga to gruntowania lub odpowiedniej obróbki powierzchni, aby umożliwić montaż produktów poprzez klejenie i ułatwić odpowiednią przyczepność (adhezję) farb, uszczelniaczy lub innych materiałów funkcjonalnych i dekoracyjnych. Biorąc powyższe pod uwagę, cel niniejszego artykułu jest dwojaki: (1) Zbadanie i ocena szeregu procesów zwiększających przyczepność (adhezję) TPO i innych tworzyw sztucznych, np. obróbka płomieniowa, podkłady chloro-poliolefinowe (CPO) i zastrzeżony proces inżynierii powierzchni (SICORä) oraz ocena ich przydatności do wielu zastosowań w produktach motoryzacyjnych, oraz (2) przedstawienie praktycznych przykładów wykorzystania procesu SICORä do kontroli przyczepności (adhezji) w przemyśle motoryzacyjnym.
15
Content available remote Weryfikacja możliwości wzmocnienia nasady łopaty wirnika nośnego wiatrakowca
PL
W publikacji przedstawiono zagadnienie wzmocnienia nasady łopaty wirnika nośnego wiatrakowca przez wklejenie kieszeni łopaty. Technologia klejenia jaką zastosowano została opracowana dla stopu aluminium 6005 T6, z którego wykonane zostały łączone elementy. W celu opracowania optymalnych parametrów klejenia przeprowadzono szereg badań, w wyniku których dobrano substancję klejącą oraz sposób przygotowania powierzchni, zapewniający największą wytrzymałość statyczną połączenia. Obiekt badań stanowi łopata wirnika nośnego wiatrakowca oraz kieszeń będąca łącznikiem między łopatą a głowicą wirnika wiatrakowca. Oba elementy zostały zaprojektowane w ramach projektu „Nowoczesny wirnik autorotacyjny”. W celu opracowania metody wklejania kieszeni na nasadę łopaty sprawdzono wytrzymałość połączenia dla różnych wariantów montażu kieszeni. Pierwszy wariant polegał na nasunięciu kieszeni na łopatę, w drugim natomiast wykorzystano kieszeń przecięta wzdłuż krawędzi natarcia. Drugi wariant powstał po wstępnych próbach, które ujawniły wady nasuwania kieszeni na jej nasadę niezależnie od kierunku nasuwania. Wyniki badań zostały zestawione z wynikami zrywania nasady łopaty, na którą nie naklejano kieszeni (kieszeń była montowana tylko śrubami). Zestawienie wyników zweryfikowało możliwość wzmocnienia nasady łopaty przez wklejanie kieszeni, stopień wzmocnienia i określiło optymalne rozwiązanie montażu kieszeni na nasadzie łopaty. Zrealizowany proces badawczy może stanowić zarówno próby dowodowe wytrzymałości nasady łopaty wirnika wiatrakowca i podstawę do wprowadzenia wdrożenia opracowanej technologii klejenia dla wykorzystywanego do produkcji łopat stopu aluminium.
EN
The paper presents the issue of strengthening the gyroplane rotor blade base by bonding the blade socket to it. Adhesive technology for aluminum alloy 6005 T6 has been developed. In order to develop optimal bonding parameters, a number of tests has been conducted, which resulted with selecting the best adhesive and the best method of surface preparation that provides the highest static strength. The test objects are, the gyro rotor blade and socket which is the link between the blade and the hub of gyroplane rotor, both elements were designed in Modern Autorotating Rotor Project. In order to develop a method of bonding a socket on the blade base the joint strength was tested for different way of socket installation. The first variant was pushing socket on the base of rotor blade, and another which uses the pocket cut along the leading edge. The second variant was created after initial tests that revealed defects in the socket docking on the rotor blade base, regardless of the direction of the docking. The results are compared with results of strength tests of the rotor blade base, where socket was only mount by screws. Summary of results verified the possibility to strengthen the rotor blade base by bonding socket and identified the optimal socket mounting solution on rotor blade base. Carried out the research process can be evidence strength test of gyroplane rotor blade base as well as basis for the implementation of bonding technology to use in the production of aluminum alloy rotor blades.
PL
W artykule opisano przebieg badań doświadczalnych, mających na celu określenie technologii klejenia dla stopów aluminium. Proces opracowania technologii oparto na badaniach anodowanego stopu aluminium 6005 T6. Z wybranego stopu aluminium wykonuje się elementy wirnika nośnego wiatrakowca tj. łopaty oraz kieszenie łopat. We wstępie artykułu przedstawiono zalety procesu klejenia w zastosowaniach lotniczych. Opisano warianty przygotowania powierzchni i dobór substancji klejącej, spośród dedykowanych aluminium, dwuskładnikowych klejów epoksydowych oraz żywicy epoksydowej z wypełniaczem. Omówiono kolejne etapy przygotowania każdej z czterech z zaproponowanych metod przygotowania powierzchni. Opisano przebieg badań oraz stanowisko badawcze zapewniające czyste ścinanie połączeń klejonych. System akwizycji danych zapewnił rejestracje przebiegu siły w funkcji przemieszczenia. Przeanalizowano zalety i wady wybranych wariantów połączeń w odniesieniu do zastosowań w lotnictwie, uwzględniając warstwę anody, która nie powinna być naruszona podczas przygotowania powierzchni. Na podstawie wytrzymałości statycznej na ścinanie oraz pozostałych kryteriów (tj. łatwość przygotowania mieszanki klejącej i aplikacji kleju, pracochłonność przygotowania powierzchni oraz minimalizacja ingerencji w warstwę anodowaną, koszty, czas potrzebny do pełnego utwardzania) określono optymalne parametry klejenia dla duralu 6005 T6. Przeprowadzone prace badawcze i otrzymane wyniki wytrzymałości statycznej połączeń klejonych stanowią podstawę do wykorzystania opracowanej technologii na rzeczywistym obiekcie. Analiza wyników uwzględniająca wszystkie zawarte w pracy badawczej kryteria pozwoliła na określenie optymalnych parametrów połączenia klejonego, tj. konkretnej mieszanki klejącej przy jednej z przebadanych powierzchni klejenia.
EN
This article describes the testing process to determine bonding technology for aluminum alloys, this process was developed based on anodized 6005 T6 aluminum alloy research. The components of gyro rotor ie. the blades and blades pockets are made of that aluminum alloy. In the introduction of this paper advantages of the bonding process in aerospace industry are presented. Variants of surface preparation and selection of the adhesive (dedicated to aluminum two-component epoxy adhesives and epoxy resin with the filler) were described. Discussed the steps of preparing each of four of the proposed methods of surface preparation. The conduct of the study and test stand to provide a pure shear bonded joints were describes. The data acquisition system assured the registration course of force versus displacement. The advantages and disadvantages of selected variants joints for uses in aviation, taking into account the anode layer, which should not be violated during surface preparation were analyzed. On the basis of static shear strength and other criterias (ie. the ease of adhesive mixture preparation, adhesive application, surface preparation workload to minimize interference with the anodized layer, costs and time needed for a full curing) for optimal adhesion for 6005 T6 aluminum alloy were determined. Conducted research and the results of bonded joints static strength provide a basis for the use technology to the real object. Analysis of the results, taking into account all included criteria allowed to define optimum conditions for adhesive connection, selected adhesive for one of the tested bonding surface.
17
Content available remote Spawanie laserowe – wybrane metody
PL
W artykule przedstawiono podstawy i odmiany procesu spajania materiałów na drodze spawania laserowego. Odkrycie promieniowania laserowego w połowie XX w. przyczyniło się do dynamicznego rozwoju technik spajania materiałów. Źródło energii w postaci wiązki laserowej okazało się być w wielu przypadkach idealnym narzędziem w procesach spajania ze względu na swoją niespotykaną dotąd specyfikę. Do najważniejszych atutów promieniowania laserowego w aspekcie wykorzystania go w procesach spawania bez wątpienia zaliczyć można elastyczność w zakresie gęstości używanych energii, jak również możliwość praktycznie dowolnego formowania kształtu i rozkładu energii w wiązce. Dzięki między innymi tym cechom proces spawania laserowego może być realizowany na wiele różnych sposobów oraz zastosowany do wielu różnych typów materiałów.
EN
The article the basics and variations of the process of bonding materials by laser welding. Discovery of the laser radiation in the mid-20th century, contributed to dynamic development of the bonding techniques. Source of energy in the form of a laser beam turned out to be, in many cases, an ideal tool in the process of bonding due to its unprecedented specificity. The most important strengths of laserradiation, in terms of its use in welding processes, without a doubt include the flexibility in terms of the density of energy which is used, as well as the abitity to form any shape and to distribute energy in the beam. Thanks to these features, the laser welding process can be performed in many different ways and be applied on many different types of materials.
18
Content available remote Pozorny moduł Younga klejów epoksydowych w połączeniu klejowym metali
PL
W analizie modelowej MES jednym z istotnych elementów jest dokładne określenie stałych materiałowych takich jak moduł Younga czy współczynnik Poissona. Z reguły określa się je w standardowych próbach na próbkach „wiosełkowych” lub przyjmuje na podstawie dostępnej literatury. W przypadku połączeń klejowych sprawa jest bardziej skomplikowana. Klej w stanie płynnym, w kontakcie z powierzchnią metalu, podlega silnemu oddziaływaniu pola sił fizysorpcyjnych i chemisorpcyjnych na granicy faz. W efekcie w bezpośredniej strefie granicznej następuje specyficzne porządkowanie struktury co skutkuje zmianą właściwości tej strefy w stanie utwardzonym. Grubość tej strefy zależy od wielu czynników, najczęściej zmiana tych właściwości przejawia się wzrostem sztywności utwardzonego kleju w tej strefie. Zjawisko to znane jest jako „pozorny” moduł Younga. W sytuacji, gdy grubość warstwy kleju jest mała, a tak z reguły jest w przypadku połączeń metali, zjawisko to może w istotny sposób zwiększać niepewność otrzymanych wyników symulacji. W pracy przedstawiono badania porównawcze polegające na wyznaczeniu współczynnika sprężystości wzdłużnej kleju dla próbek „wiosełkowych” oraz kleju w spoinie klejowej dla próbek „przekładkowych”. Wyznaczono różnicę w wartości modułu Younga kleju epoksydowego oraz spoiny klejowej. Rozważano wpływ tej różnicy na stopień zgodności otrzymywanych wyników symulacji MES z wynikami badań niszczących.
EN
In FEM analysis one of crucial elements is to accurately determine material constants like Young’s modulus or Poisson’s ratio. In general these constants are identified in standard tests on dumbbell-shaped samples or assumed based on available literature. In case of adhesive joints issue is much more complicated. Adhesive in its uncured state, in contact with surface of the metal, is subjected to impact of physisorption and chemisorption forces at the phase boundary. In the effect of this in the direct boundary zone occurs specific structure ordering, which results in modification of properties of this area in cured state. Thickness of this zone is dependent on various factors, predominantly change of these properties results in increased glue rigidity. This phenomenon is known as “apparent” Young’s modulus. In case, where thickness of glue layer is small, as it is typically for adhesive metal joints, this phenomenon might significantly increase uncertainty of the results of the FEM simulation. Comparative studies were shown involving the determination of the elastic modulus of adhesive of the dumbbell samples and an adhesive joint in the interleaved samples. The difference in the value of Young’s modulus of adhesive epoxy material and adhesive joint was determined. The impact of this difference on the degree of compliance of FEM simulation in comparison with results of destructive testing was considered.
19
Content available remote Mikrospawanie laserowe
PL
W artykule przedstawiono podstawy mikrospawania laserowego. Jest to bardzo precyzyjna technika łączenia materiałów znajdująca bardzo szerokie zastosowanie w przemyśle. Wytwarzanie mikro i mezo elementów należy dzisiaj do jednego z wiodących nurtów wytwarzania, dlatego też mikrospawanie laserowe znajduje coraz większe zastosowanie i stanowi obszar intensywnych badań. W procesie tym powstaje spoina która swymi wymiarami nie przekracza 1 mm. Ze względu na specyfikę oddziaływania laserowego strefa wpływu ciepła jest niewielka w stosunku do innych technik spawania. Do mikrospawania laserowego używa się laserów impulsowych Nd:YAG, CO2 lub laserów światłowodowych. Mikrospawanie jest procesem powtarzalnym, dającym efektywne spoiny i poddającym się automatyzacji.
EN
The paper presents some aspects of laser micro-welding. It is a very precise technique of joining materials which finds very wide application in the industry. The production of micro and meso elements is today one of the leading trends of manufacturing, so laser micro-welding is widely used in industry and is an area of intensive research. Dimensions of the welds formed in this process do not exceed 1 mm. Due to the specificity of the laser beam the heat affected zone is small in relation to other welding techniques. For laser micro-welding pulsed laser Nd:YAG, CO2 or fiber laser are used. Laser micro-welding is a repetitive process which gives an effective weld and which gives to automate.
EN
The aim of the study was to assess the value of the breaking force of the bonding between selected polymer cements, root dentin and fiber reinforced composite (FRC) posts. Five resin based luting cements were selected for use in the study. Tests were performed on a total of 30 teeth, which were divided into two groups. Fifteen teeth were installed vertically and 15 with an angle of 45°. All samples were exposed to crushing forces in an Instron 4411 device. After the strength tests, each sample was analyzed by micro-CT (micro computed tomography) in order to verify that the forces did not cause defects in the areas of the adhesive connection. The differences observed in the present study only involved the posts that failed at different values of the acting forces – in the case of the vertical sample, x =532.5 N and in the case with an angle of 45°, x = 117.9 N. For the micro-CT images, there were no defects in the analyzed areas of the adhesive connections. Under the conditions of the current study, all selected polymer cements showed the required level of bonding.
PL
Oceniono wytrzymałość połączenia cementów polimerowych z zębiną kanałową i wkładem wzmocnionym włóknem szklanym. Zbadano pięć rodzajów polimerowych cementów stosowanych do stałego osadzania wkładów. Przeprowadzono test wytrzymałościowy 30 próbek zębów, podzielonych na dwie grupy: 15 zębów osadzonych pionowo i 15 zębów osadzonych pod kątem 45°. Wszystkie próbki poddano działaniu siły zgniatającej za pomocą urządzenia Instron 4411, a następnie każdą próbkę analizowano metodą mikroobrazowej tomografii komputerowej (mikro-CT) w celu sprawdzenia stanu połączenia między zębiną i cementem oraz wkładem i cementem. W żadnym wypadku nie stwierdzono zerwania połączenia. Zaobserwowano jedynie różnice wartości siły uszkadzającej wkład. W wypadku próbki ustawionej pionowo wyniosła ona średnio 532,5 N, a próbki ustawionej pod kątem – 117,9 N. W obszarach analizowanych metodą mikro-CT nie stwierdzono zerwania połączenia. W warunkach przeprowadzonego badania wszystkie wybrane cementy polimerowe wykazały oczekiwany poziom połączenia.
first rewind previous Strona / 3 next fast forward last
JavaScript jest wyłączony w Twojej przeglądarce internetowej. Włącz go, a następnie odśwież stronę, aby móc w pełni z niej korzystać.