Preferencje help
Widoczny [Schowaj] Abstrakt
Liczba wyników

Znaleziono wyników: 10

Liczba wyników na stronie
first rewind previous Strona / 1 next fast forward last
Wyniki wyszukiwania
Wyszukiwano:
w słowach kluczowych:  DAQ
help Sortuj według:

help Ogranicz wyniki do:
first rewind previous Strona / 1 next fast forward last
EN
A novel approach to a trigger mode in the Gas Electron Multiplier (GEM) detector readout system is presented. The system is already installed at WEST tokamak. The article briefly describes the architecture of the GEM detector and the measurement system. Currently the system can work in two trigger modes: Global Trigger and Local Trigger. All trigger processing blocks are parts of the Charge Signal Sequencer module which is responsible for transferring data to the PC. Therefore, the article presents structure of the Sequencer with details about basic blocks, theirs functionality and output data configuration. The Sequencer with the trigger algorithms is implemented in an FPGA chip from Xilinx. Global Trigger, which is a default mode for the system, is not efficient and has limitations due to storing much data without any information. Local trigger which is under tests, removes data redundancy and is constructed to send only valid data, but the rest of the software, especially on the PC side, is still under development. Therefore authors propose the trigger mode which combines functionality of two existing modes. The proposed trigger, called Zero Suppression Trigger, is compatible with the existing interfaces of the PC software, but is also capable to verify and filter incoming signals and transfer only recognized events. The results of the implementation and simulation are presented.
2
Content available SoPC-based DMA for PCI Express DAQ cards
EN
This paper presents low-cost, configurable PCI Express (PCIe) direct memory access (DMA) interface for implementation on Intel Cyclone V FPGAs. The DMA engine was designed to support DAQ tasks including pre-triggering acquisition for transient analysis and multichannel transmission. Performance of the interface has been evaluated on Terasic OVSK board (PCIe Gen2 x4). Target configuration of this interface is based on the Avalon-MM Hard IP for Cyclone V PCIe core and Jungo WinDriver x64 for Windows. A sample speed of 1200 MB/s has been reported for DMA writes to PCIe memory.
EN
The paper presents improvements of the developed system for hot plasma radiation measurement in the soft Xray range based on a Gas Electron Multiplier (GEM) detector. Scope of work consists of a new solution for handling hardware time-synchronization with tokamak systems needed for better synchronization with other diagnostics and measurement quality. The paper describes the support of new modes of triggering on PC-side. There are communication and data path overview in the system. The new API is described, which provide separate channels for data and control and is more robust than the earlier solution. Work concentrates on stability and usability improvements of the implemented device providing better usage for end-user.
PL
Artykuł prezentuje możliwości i ocenę parametrów karty pomiarowej M3i.2122 firmy Spectrum Systementwicklung Microelectronic. Opisane przykłady detekcji sygnału sinusoidalnego zostały zrealizowane w środowisku obliczeniowym MATLAB. W artykule zaprezentowano podstawowe metody ekstrakcji sygnału z szumu za pomocą uśredniania niekoherentnego i filtracji DFT. Przedstawiona karta jest dobrym, alternatywnym rozwiązaniem do znanych systemów akwizycji danych np. opartych o platformę PXI.
EN
The hardware features of the M3i.2122 data acquisition card and detection of a sinusoidal signal are presented in this paper. The function block diagram of the card is shown in Fig 1. System data transfer is realized with use of a PCI Express bus. A single 4 MHz tone at –93 dBm power level was selected as the test signal. The basic methods of extracting signal from noise using incoherent averaging and DFT’s processing gain were implemented on the M3i.2122 card. The gain of incoherent averaging is shown in Fig. 2 and DFT’s processing gain is noticeable if we compare Fig. 2a and Fig. 3a, where the number of samples has increased from 1024 to 8192. Figures 2 and 3 also show that the use of signal windowing may decrease the signal-to-noise ratio. The effects of enabling an integrated anti-aliasing filter (Fig. 4) show that this filter is insufficient in the context of detection of weak signals and should be replaced by an external anti-aliasing filter with good properties. In spite of this drawback, the presented card is a good alternative to the well known data acquisition systems such as the PXI -based platform for weak signal detection.
EN
This article is focused on data acquisition system (DAQ) designed especially to be used in positron emission tomography (PET) or single-photon emission computed tomography. The system allows for continuous registration of analog signals during measurement. It has been designed to optimize registration and processing of the information carried by signals from the detector system in PET scanner. The processing does not require any rejection of data with a trigger system. The proposed system possesses also an ability to implement various data analysis algorithms that can be performed in real time during data collection.
PL
Celem pracy było zaprojektowanie układu elektronicznego współpracującego z wielofunkcyjną kartą akwizycji danych DAQ. Założeniem projektu było rozszerzenie możliwości dydaktycznych laboratorium komputerowych systemów pomiarowych. W ramach pracy zaprojektowano układ generatora sygnałów okresowo zmiennych typu unipolarnego, generator sygnałów różnicowych oraz układy sterowania serwonapędami modelarskimi oraz napędami prądu stałego.
EN
The aim of this study was to design an electronic circuit cooperating with multifunction data acquisition card DAQ. Assumption the project was to extend the capabilities of educational laboratory of measurement systems. The cyclic signal generators with single and differential signal were designed, control systems for servo drives and DC motors were designed as well.
PL
W artykule zaprezentowano urządzenie służące do pomiaru szesnastu sygnałów napięciowych wolnozmiennych. Przeznaczeniem zaprojektowanego urządzenia jest ułatwienie czynności serwisowych nowoczesnych urządzeń elektronicznych. Informacja o stanie napięć w kluczowych punktach układu (często dostępnych poprzez złącze diagnostyczne) pozwala w sposób natychmiastowy ocenić powód usterki. Założeniem projektowym było utrzymanie niskiej ceny bez utraty kluczowej funkcjonalności.
EN
Service operations always begin with a diagnosis of the malfunctioning device. Trustworthy methods for localisation of a source of damage are key to fast restoration of the equipment efficiency. Most of present electronic equipment have diagnostic connectors which simplify this operation. A measurement of significant voltage signals is the easiest approach to find a failure. In this paper the principles of functioning and a manner of realization of a multichannel low frequency signal acquisition system are presented. The core of the system is a modern microcontroller STM32F103 [1] based on ARM CortexM3 architecture. As a result of this selection a low cost but still powerful acquisition device is built. A low measurement frequency is the effect of project requirements - power supply malfunction is a frequent cause of electrical devices malfunctions. The measurement and analysis of high speed digital transmission signals is a subject of a separate diagnosis problem and is not discussed in the paper. The measurement device design is as simple as possible as an effect of nonindustrial environment and low cost elements used. Tests proved a sufficient level of robustness and measurement ability for the desired diagnostic application. Professional manufacturing of the device is planned after extensive testing.
8
Content available Bezprzewodowy system akwizycji danych
PL
W artykule przedstawiono koncepcję i opis budowy bezprzewodowego systemu pomiarowego. Wykorzystując transmisję bluetooth, zbudowano wieloczujnikowy system akwizycji, w którym każdy z modułów czujnikowych pracuje równolegle. Umożliwia to równoczesny pomiar wielu wielkości elektrycznych i nieelektrycznych w tym samym czasie. W artykule przedstawiono budowę szybkiego czujnika, implementację małego systemu operacyjnego sterującego jego pracą. Przedstawiono propozycję rozwiązania napotkanych przy budowie problemów z zakłóceniami i analizą danych. W module czujnikowym zaimplementowano system poleceń sterujących pracą modułu oraz przesyłający pobrane dane do jednostki zarządzającej. Przedstawiono wyniki pomiarów wykonanych na systemie eksperymentów. Zbudowano aplikację analizującą i wizualizującą wyniki pomiarowe z czujnika przyspieszeń podłączonego do modułu. Przeprowadzono i omówiono również eksperyment badający równoległą transmisję z dwóch czujników pracujących na tym samym sygnale mierzonym.
EN
The article presents a concept and a description of the construction of a wireless measurement system based on the Bluetooh transmission. In which each of the sensing modules working in parallel. This allows simultaneous measurement of electrical and non-electrical quantities at the same time. The article presents: the construction of a measurement module, an implementation of a small operating system, controlling its work; proposal of solutions encountered in the construction of noise problems and data analysis. The sensing module implements the system of commands that control the module and transmits the retrieved data to the management unit. The results of measurements made on a system for experimentation. Analyzing the application was built and visualizing the results of measuring the acceleration sensor is connected to the module. Performed and discussed a parallel experiment examining transmission of the two sensors working on the same signal measured.
9
Content available remote Long signals handling within Simulink models using Level-2 M-File S-Functions
EN
Simulation of nonstationary processes sometimes requires very long, real excitation signal. Unfortunately Simulink file I/O blocks read or write whole files at the time. The paper gives an advice on how to handle (read and write) long signals within Simulink in a frame based manner. Presented functions were developed as Level-2 M-File S-Functions. They can read or write raw binary data files, containing multiple signals. Such files are generated by multichannel Data Acquisition (DAQ) systems.
10
Content available remote System odczytu i akwizycji danych Monitora Świetlności eksperymentu ZEUS
PL
W artykule przedstawiono opis systemu odczytu i akwizycji danych Monitora Świetlności eksperymentu ZEUS na akceleratorze HERA w Instytucie Deutsches Elektronen-Synchrotron, Hamburg, Niemcy. Artukuł opisuje koncepcję i realizację systemu dostosowanego do wymagań różnych detektorów wchodzących w skład Monitora Świetlności.
EN
A readout electronics and data aquisition system for the Luminosity monitor of ZEUS experiment on HERA accelerator at Deutsches Elektronen-Synchrotron, Hamburg, Germany is described. Conceptions and practical realization of readout and DAQ system for different detectors is shown in details.
first rewind previous Strona / 1 next fast forward last
JavaScript jest wyłączony w Twojej przeglądarce internetowej. Włącz go, a następnie odśwież stronę, aby móc w pełni z niej korzystać.