Wyniki wyszukiwania - BazTech

1

Application of BCHMX in Shaped Charges against RHA Targets Compared to Different Nitramine Explosives

Elbeih A., Elshenawy T., Zeman S., Akstein Z.

Central European Journal of Energetic Materials

|

2018

|

Vol. 15, no. 1

3--17

EN

In this work, a new bicyclic nitramine, cis-1,3,4,6-tetranitro-octahydroimidazo-[4,5-d]imidazole (bicyclo-HMX or BCHMX), has been tested for its performance as a shaped charge explosive filler in comparison with three other interesting cyclic nitramines. Four shaped charges were prepared using different nitramine-based plastic bonded explosives (PBXs), and their performance was measured experimentally in terms of the penetration depth into laminated rolled homogeneous armour (RHA) targets. The explosive fillers were highly pressed PBXs based on RDX, HMX, BCHMX and CL-20, bonded by Viton A binder. The Autodyn numerical hydrocode was implemented to determine the shaped charge jet’s characteristics and its penetration depth. The experimental and calculated detonation characteristics of the explosives used are reported. Relationships between the detonation characteristics of the explosives and the jet characteristics were observed. The results show that CL-20 is the most powerful explosive, with the largest penetration depth into the RHA target, while BCHMX explosive has a relatively enhanced penetration depth with respect to RDX explosive. The results of the Autodyn code calculations are consistent with the experimental measurements, with a maximum difference of 6.6%.

2

Effect of Different Polymeric Matrices on the Sensitivity and Performance of Interesting Cyclic Nitramines

Elbeih A., Zeman S., Jungova M., Akstein Z.

Central European Journal of Energetic Materials

|

2012

|

Vol. 9, nr 2

131-138

EN

Different polymeric matrices, based on butadiene-styrene rubber, polymethyl-methacrylate and silicone binders, were investigated for their ability to decrease the sensitivity of explosives to different mechanical stimuli. A series of plastic explosives based on four different nitramines, namely RDX (1,3,5-trinitro- 1,3,5-triazacyclohexane), β-HMX (β-1,3,5,7-tetranitro-1,3,5,7-tetrazacyclooctane), BCHMX (bicycloHMX, cis-1,3,4,6-tetranitro-octahydroimidazo-[4,5- d ]imidazole) and ε -HNIW (ε -2,4,6,8,10,12-hexanitro-2,4,6,8,10,12-hexaazaisowurtzitane, ε-CL-20), bonded by the selected polymeric matrices were prepared. Sensitivity to impact of all of the plastic explosives prepared as well as of the pure explosives, was measured using the fall hammer test. Sensitivity to friction was determined using the BAM friction test. The performance was studied using the ballistic mortar test and the results were recorded relative to TNT (trinitrotoluene) as reference. By comparing the results of impact and friction sensitivities, it is obvious that the mechanism of transfer of the friction force to the reaction center of the nitramine molecule should be different from that of impact energy transfer. The silicone binder appeared to be the best polymer for decreasing the sensitivity of explosives. The results of the ballistic mortar proved that the performance of the plastic explosives prepared is affected by the type and weight percentage of the binder in each sample.

3

Replacement of PETN by Bicyclo-HMX in Semtex 10

Elbeih A., Pachman J., Zeman S., Akstein Z.

Problemy Mechatroniki : uzbrojenie, lotnictwo, inżynieria bezpieczeństwa

|

2010

|

Vol. 1, Nr 2 (2)

7-16

EN

Bicyclo-HMX (BCHMX) was studied in the form of a plastic explosive bonded by the plastic matrix of the explosive Semtex 10 and the results were compared with the original Semtex 10 which contains PETN as an explosive filler. The tests included measurements in the sensitivity to impact and friction. The thermal stability was studied using differential thermal analysis (DTA) with the evaluation of the outputs using the Kissinger method. The detonation velocity was measured experimentally and the detonation characteristics were calculated by means of EXPLO 5 code and the Kamlet & Jacobs method. On the basis of mutual comparison of all the obtained results, it was concluded that replacement of PETN by Bicyclo-HMX enhances the friction sensitivity, thermal stability and the detonation parameters of the explosive Semtex 10, while the impact sensitivity is approximately the same. Calculated results of EXPLO 5 code showed good agreement with the experimental detonation velocities.

4

Thermal Stability and Detonation Characteristics of Pressed and Elastic Explosives on the Basis of Selected Cyclic Nitramines

Elbeih A., Pachmáň J., Zeman S., Trzciński W. A., Akstein Z., Sućeska M.

Central European Journal of Energetic Materials

|

2010

|

Vol. 7, nr 3

217-232

EN

Bicyclo-HM X (cis-1,3,4,6-tetranitro-octahydroimidazo-[4,5-d] imidazole or BCHM X) was studied as a plastic explosive bonded with the C4 matrix and with Viton A. Also a series of nitramines namely RDX (1,3,5-trinitro-1,3,5=triazinane), HM X (1,3,5,7-tetranitro-1,3,5,7-tetrazocane) and HNIW (ĺ-2,4,6,8,10,12-hexanitro-2,4,6,8,10,12-hexaazaisowurtzitane, ĺ-CL-20) were studied for comparison with the same types of binders. The detonation velocity, D, of all prepared mixtures was measured. Their thermal stability was determined using non-isothermal differential thermal analysis (DTA). While the C4 matrix lowers the thermal stability of the resulting explosives, Viton A enhances this stability. Approximate relationships between the peaks of exothermic decomposition and the D values were found. The detonation parameters were also calculated by means of Kamlet & Jacobs method, CHEETAH and improved EXPLO5 code for all the mixtures. From the measured D values and the calculated detonation parameters, it is obvious that the detonation parameters of BCHM X-mixtures are very close to HM X-explosives and better than those of RDX-mixtures. It was found that the C4 matrix reduces the difference between the values of energy of detonation in the studied C4 mixtures. As expected, the pressed HNIW-Viton A mixture has the highest detonation parameters of all of the prepared mixtures.