Preferencje help
Widoczny [Schowaj] Abstrakt
Liczba wyników

Znaleziono wyników: 8

Liczba wyników na stronie
first rewind previous Strona / 1 next fast forward last
Wyniki wyszukiwania
Wyszukiwano:
w słowach kluczowych:  membrana kapilarna
help Sortuj według:

help Ogranicz wyniki do:
first rewind previous Strona / 1 next fast forward last
PL
Przedstawiono głowicę modułu kapilarnego z dwoma warstwami klejenia membran kapilarnych, rozdzielonymi szczeliną powietrzną. Uszkodzenie klejenia powoduje przeciek do komory pomiędzy klejeniami, skąd ciecz swobodnie wypływa na zewnątrz nie zanieczyszczając destylatu. Skuteczność pracy nowej konstrukcji modułu potwierdzono w badaniach długoterminowych.
EN
A new design of capillary module head with two layers of epoxy resin separated by air-gap was presented. In case of potting failure the leakage of feed into the air-gap proceeds. The feed flows out from this air-gap preventing distillate contamination. The long-tenn investigations confirmed a good efficiency of the design presented.
EN
Encapsulation of bacteria in a semipermeable polymer membrane gives a lot of technological possibilities. Our aim was to evaluate the performance of bacteria encapsulated in hollow fibers when treated with chosen antibiotic. The antibiotic application may cause release of biologically active substances for which production the bacteria may be genetically modified. The encapsulated in HF bacteria Escherichia coli transfected with pQE-GFP (green fluorescent protein) plasmid were incubated with addition of gentamycin or tetracycline. The encapsulated in hollow fibers E. coli culture with addition of tetracycline proves the tetracycline impact on the bacteria viability increasing the necrotic bacteria share. Polypropylene modified membranes allow to avoid permeation of the bacteria through the membrane wall. E. coli encapsulated in HF may be used in future, in systems releasing the therapeutic factor.
4
Content available remote Zinc(II) extraction from hydrochloric acid solutions in hollow fiber modules
EN
We have established the comprehensive analysis of non-dispersive solvent extraction (performed in hollow fiber modules) of zinc from hydrochloric acid solution with TBP and elucidated the consistent mathematical model, based on the general law of mass transfer continuity and on flow pattern of each phase. Eventually, a full unsteady-state mathematical model was formulated and then verified by the available experimental data. Moreover, a very important kinetic parameter (mass transfer coefficient, k) was estimated, the zinc(II) concentration profile was drawn, and the principal resistance to zinc(II) mass transfer was pointed out.
EN
Aerosol flow and particle deposition in the anatomical cast of human upper airways (mouth-throat-pharynx) were studied using CFD. Temporal and spatial distributions of the deposition efficiency for particles in the range of 0.3-10 micrometers were obtained. Computational results were compared with experimental data obtained using the silicon cast - and programmable pump ("artificial lung")- The meaning of the results for toxicology and pharmacology (inhalation therapy) was discussed.
EN
Highly biocompatible and mechanically resistant semipermeable membranes are required for macroencapsulation of cells or tissues. For this purpose two series of aromatic as well as aliphatic polyurethanes were elaborated for the production of hollow fibre membranes by the phase inversion method and the wet spinning technique. The influence of the polyurethane structure, i.e. type of the hard segments and content of the soft segments on the membrane morphology and its transport properties were investigated.
EN
The mixing-cup concentration for hollow-fiber membrane is investigated under different flow conditions (parabolic flow and plug flow) and at different concentration dependent diffusivity and solubility. The results show significant effect of flow conditions on the concentration in the hollow fiber. Similarly the variable diffusivity and solubility have significant influence on the process.
PL
Badano rozkłady stężenia z uwzględnieniem mikromieszania w modułach kapilarnych dla różnych warunków przepływu (laminamy i burzliwy) oraz przy różnych stężeniach zależnych od dyfuzyjności i rozpuszczalności. Wyniki pokazały znaczący wpływ warunków przepływowych na stężenie w modułach kapilarnych. Podobnie, zmienna dyfuzyjnośc i rozpuszczalność mają istotny wpływ na proces membranowy.
PL
Modyfikowano powierzchnię polipropylenowych, półprzepuszczalnych membran kapilarnych przy zastosowaniu różnych sposobów silanizacji, badając wpływ pokrywania powierzchni membran na ich własności transportowe z punktu widzenia przyszłych zastosowań in vivo. Badano też obrastanie tkanką łączną membran modyfikowanych różnymi sposobami we wszczepach in vivo. Stwierdzono, że badane membrany spełniają wymogi membran do immunoizolacji komórek.
EN
The permiselective polypropylene hollow fiber's surface was modified using different ways of silanization and the influence of silanization on membrane transport properties was assessed. The tissue overgrowth of different modified membranes was evaluated in vivo. It was found that the membranes comply with the requirements for membranes applied for immunoisolation.
first rewind previous Strona / 1 next fast forward last
JavaScript jest wyłączony w Twojej przeglądarce internetowej. Włącz go, a następnie odśwież stronę, aby móc w pełni z niej korzystać.