Preferencje help
Widoczny [Schowaj] Abstrakt
Liczba wyników

Znaleziono wyników: 3

Liczba wyników na stronie
first rewind previous Strona / 1 next fast forward last
Wyniki wyszukiwania
Wyszukiwano:
w słowach kluczowych:  magistrala I2C
help Sortuj według:

help Ogranicz wyniki do:
first rewind previous Strona / 1 next fast forward last
PL
Diody LED stosowane w urządzeniach świetlnych drogowej sygnalizacji świetlnej, iluminacji estradowej oraz budynkowej z uwagi na dynamikę scen świetlnych, wymagają zaawansowanego sterowania. Sterownik diod LED oraz układy nadzorujące muszą być połączone z mikrokontrolerem za pomocą magistrali komunikacyjnej. Artykuł przedstawia kryteria wyboru oraz sposób zastosowania magistrali I2C w urządzeniu świetlnym emitującym dynamiczne sygnały świetlne RGB (RED/GREEN, BLUE) lub RG (RED/GREEN), które sterowane jest sygnałem DMX.
EN
LEDs used in traffic light devices, stage and building illumination require advanced control due to the dynamics of light scenes. The LED driver and supervising systems must be connected to the microcontroller via a communication bus. This article presents the selection criteria and how to use the I2C bus in a lighting device emitting dynamic RGB (RED/GREEN, BLUE) or RG (RED/GREEN) light signals, which is controlled by a DMX signal.
2
PL
W artykule przedstawiono sterownik diod LED o konfigurowalnej liczbie kanałów, służący do zasilania sześciu diod małej mocy. Prąd diod może być ustawiany cyfrowo z krokiem 0,5 mA w zakresie od 0 do 32 mA. Do sterowania prądem w poszczególnych kanałach wykorzystano magistralę szeregową I2C. Dzięki zastosowaniu mikrokontrolera, możliwe jest zaprogramowanie różnych efektów świetlnych, zarówno statycznych jak i dynamicznych. W artykule zaprezentowano wyniki badań eksperymentalnych.
EN
The 6-channel LED controller equipped with a high efficiency fractional charge pump is presented in the article. Each channel has got a programmable dimming current. To ensure uniform brightness in any application, each LED channel delivers an accurate regulated current from the range from 0 to 32 mA. The LED channels are configured into three independent pairs, each containing two matched channels. Each pair can be separately programmed in 0,5 mA steps, using the I2C serial bus. Thanks to the additional microcontroller with EEPROM memory, many different light scenes can be stored and used in a desired circumstance. Some of the laboratory results are presented as well.
3
Content available Optyczna transmisja sygnału w magistrali I2C
PL
Artykuł prezentuje zagadnienia związane z możliwością transmisji sygnału opartego o magistralę I2C poprzez optyczny system światłowodowy. Przedstawiono aplikacje umożliwiające konwersję sygnału magistrali na sygnał optyczny z wykorzystaniem konwertera P82B96. Transmisję światłowodową realizować można poprzez klasyczny układ dioda LED - fotodetektor, układy TOSLINK lub system WDM. Opracowane modelowe aplikacje optycznego łącza obsługującego sygnały magistrali I2C pozwalają na budowę rzeczywistych układów konwersji dwukierunkowego sygnału magistrali do postaci optycznej.
EN
The paper presents the problem connected with possibility of signal transmission over I2C bus through optical system. I2C is a synchronic bus through which data are sent in 8-bit frames (Fig. 3) [4]. It consists practically of two signal lines: The SDA ( data line - Serial Data Line), the SCL ( clock line - Serial Clock Line) and the ground cir-cuit (Fig. 2). The schematic diagram of a system with I2C bus is shown in Fig. 1. There three possible solutions of optical application of the bus based on use of a converter P82B96 (Fig. 4) [2] and optical fiber to transfer high-speed signals ( the speed about 3,4 Mb/s) over long data transmission lines. The simplest solution of conversion the I2C signal to optical one is a configuration using LED source (λ = 940 nm) presented in Fig. 5. The PIN-photodiode works with the maximum sensitivity of about 940 nm. There should be applied three separate optical lines, broadcasting, receiving and clock, for correct operation of this arrangement. The next configuration uses an optical transmitter TOTX173 and optical receiver TORX173 assembled to pcb (Fig. 6). They are THOSIBA elements working on the wave length of 660 nm [3]. The last proposed solution is a WDM system (Wavelength Division Multiplexing) enabling si-multaneous sending signals SCL and SDA over one optical track [1].
first rewind previous Strona / 1 next fast forward last
JavaScript jest wyłączony w Twojej przeglądarce internetowej. Włącz go, a następnie odśwież stronę, aby móc w pełni z niej korzystać.