Cast irons are good examples of materials which are more sensitive to chemical composition and production conditions. In this research to improve casting quality, solidification and nucleation process in grey cast iron was investigate. In particular, attempts have been made to rationalize variation in eutectic cells with nucleation sites and eutectic solidification undercooling. Four castings with different diameter and similar chemical composition and pouring temperature and different inoculant percentage was casted. The cooling curve and maximum and minimum undercooling for each castings was measured. Also optical metallography and image analyzer has been used to determine the average eutectic cells diameter, and linear and surface densities, and volume density was calculated. The results of this research show a competitive behavior between nucleation sites and eutectic undercooling. Higher nucleation sites and higher eutectic undercooling cause higher eutectic cell density. But increasing nucleation sites by introducing inoculants to molten metal, is accompanied with reduction in eutectic undercooling. It means that inoculation and undercooling have opposite effect on each other. So, to achieve maximum cell density, it is necessary to create an optimization between these parameters.
2
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
The article presents the influence of cooling time on the structure of metal matrix composites (MMC) castings. The examination covered two types of composites manufactured by mechanical mixing. Composite reinforcement consisted of SiC particles, and the matrix consisted of AlSi9 alloy in the first case and AlSill in the second. Comparison covered samples cooled in sand moulds and gravity dies by presenting their cooling curves and their abrasive resistance.
PL
W prezentowanym artykule przedstawiono wpływ szybkości chłodzenia na strukturę odlewów z metalowych materiałów kompozytowych. Badano dwa rodzaje kompozytów wytworzonych metodą mechanicznego mieszania. Zbrojenie kompozytu stanowiły cząstki SiC, osnowę w pierwszym przypadku stop AlSi9, w drugim AlSi11. Porównano materiały chłodzone w formie piaskowej i kokili i przedstawiono ich krzywe krzepnięcia oraz odporność na ścieranie.
3
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
W artykule przedstawiono eksperymentalną metodę umożliwiającą fizyczne modelowanie stygnięcia odlewów o różnych modułach krzepnięcia w formach odlewniczych. Pierwsze modelowanie przeprowadzono na żeliwie chromowym stygnącym w klasycznej formie piaskowej i formie metalowej (kokili).
EN
The paper presents research method of cooling process of casting materials in foundry mould (sand and metal mould). First experiment became passed with use of chromium cast iron.
4
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
W artykule przedstawiono analizę procesu stygnięcia żeliwa chromowego w formie piaskowej. Proces odlewania przeprowadzono na stanowisku do eksperymentalnego modelowania stygnięcia odlewów o różnych modułach krzepnięcia w formie odlewniczej.
EN
In this paper casting analysis of chromium cast iron in sand mould has been presented. Cooling process of cast in new test stand has been observed.
5
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
W artykule przedstawiono analizę wybranych parametrów stereologicznych fazy węglikowej żeliwa chromowego odpornego na ścieranie na przekrojach modelowego odlewu [1,2] odpowiadającego odlewom grubościennym. Badania prowadzono na żeliwie chromowym odpornym na ścieranie o stałej zawartości chromu około 12% i zmiennej zawartości węgla, na trzech poziomach 1.8%, 2.4% i 3.3%.
EN
The paper presents research results of stereological parameters of chromium cast iron consisting of 12 % Cr and 1.8 %C or 2.4 %C or 3.3%C. Casting sample was obtained in special sampler [1,2].
JavaScript jest wyłączony w Twojej przeglądarce internetowej. Włącz go, a następnie odśwież stronę, aby móc w pełni z niej korzystać.