Preferencje help
Widoczny [Schowaj] Abstrakt
Liczba wyników

Znaleziono wyników: 8

Liczba wyników na stronie
first rewind previous Strona / 1 next fast forward last
Wyniki wyszukiwania
Wyszukiwano:
w słowach kluczowych:  hydraulic shock absorber
help Sortuj według:

help Ogranicz wyniki do:
first rewind previous Strona / 1 next fast forward last
EN
This paper presents the results of bench-tests and calculations assessing the influence of temperature on the performance of a two-pipe hydraulic shock absorber. The shock absorber prepared for the tests was cooled with dry ice to a temperature corresponding to that associated with the average winter conditions in a temperate climate. The temperature range of the shock absorber during testing was ensured via equipping it with a thermocouple and monitoring it with a thermal imaging camera. During testing, the shock absorber was subjected to kinematic forces of a selected frequency with two different, fixed displacement amplitudes. The results of the tests showed a direct correlation between the decrease of component resistance at lower temperatures. The rate of change in resistance was higher at lower temperatures. It was also found that the energy dissipated in one shock cycle decreased linearly with an increasing temperature. Finally, a method for determining the ideal use temperature of the shock absorber for the assumed operating conditions was also presented.
EN
The aim of this paper is to demonstrate a simulation model of an end-of-line shock absorber quality testing process, based on the rod-assembly acceleration measurements and with the use of a production tester equipped with a pneumatic excitation system. The proposed method applies a nonparametric power spectrum model, which represents a vibration pattern of a shock absorber excited with the use of a pneumatic actuator. The simulation results are shown in the paper along with the discussion ionr how to achieve the required failure mode detection performance. The paper provides numerical and experimental case studies to show the application scope of the proposed end-of-line shock absorber quality testing method and its performance.
PL
W artykule przedstawiono model symulacyjny procesu kontroli jakości amortyzatora przez pomiar przyspieszenia drgań zespołu goleni amortyzatora w trakcie wymuszenia realizowanego pneumatycznie na urządzeniu przemysłowym. Metoda wykorzystuje nieparametryczny model bazujący na widmowym rozkłdzie gęstości mocy, przedstawiającym charakterystykę drganiową badanego amortyzatora w trakcie wymuszenia realizowanego za pomocą siłownika pneumatycznego. W artykule przedstawiono wyniki symulacji. W dyskusji przedstawiono możliwości detekcji uszkodzeń. Artykuł przedstawia numeryczną i eksperymentalną analizę przypadku pokazując zakres stosowalności metody w procesie kontroli jakości oraz jej praktyczne zastosowanie.
PL
Amortyzatory hydrauliczne są zwykle wykorzystywane w układach redukcji drgań mechanicznych jako elementy pasywne. W modelowaniu i obliczeniach dotyczących układów redukcji drgań często zakłada się liniową charakterystykę siły tłumienia w funkcji prędkości amortyzatora. W rzeczywistości siła tłumienia amortyzatora jest nieliniowa w funkcji prędkości ruchu układu, czyli współczynnik tłumienia nie jest wartością stałą. Dobór odpowiedniego modelu tłumika hydraulicznego pozwala na uzyskanie w procesie symulacji wyników zbliżonych do rzeczywistego zachowania układu. Na podstawie zależności opisujących model o charakterystyce liniowej oraz model o współczynniku tłumienia zależnym od prędkości wymuszenia zostały opracowane modele komputerowe w środowisku Matlab-Simulink® i wyznaczone zostały charakterystyki amortyzatora hydraulicznego oraz gęstości widmowe mocy przyspieszenia drgań i funkcje przenoszenia układu zawieszenia. W artykule tym rozważono wpływ uwzględnienia nieliniowej charakterystyki amortyzatora hydraulicznego na modelowanie układu redukcji drgań w układach zawieszeń siedzisk.
EN
Hydraulic shock-absorbers are typically used in the vibration reduction systems as passive components. The modeling and calculations on the vibration reduction systems are often assumed to be linear damping force as a function of the damper velocity. In fact, the damping force demonstrates non-linear function of the system velocity therefore the damping coefficient is not constant. Appropriate selection of the damper model allows to obtain simulation results close to the dynamic behavior of a real system. In the paper the linear and non-linear damper models are discussed using the Matlab-Simulink® software package. Then the damper characteristics, power spectral densities of acceleration and transmissibility functions are elaborated. This paper considers an influence of the non-linear characteristics of the hydraulic shock-absorber on modeling process of the vibration reduction systems used in seat suspensions.
4
Content available Modelling of amplitude-selective-damping valves
EN
The so-called amplitude-selective-damping (ASD) valving is a relatively new approach for modifying the output of a hydraulic shock absorber. In the automotive industry ASD valves are known to improve isolation from road inputs. During more aggressive maneuvers the systems maintains the performance of a standard (non-ASD) shock absorber. In the paper, the author derives and analyzes a fairly complete state-space model of an exemplary piston-side ASD valve. The model includes key geometric and performance characteristics of the valve. The results are shown in the form of phase plane plots of force-displacement diagrams, respectively, for a twin-tube shock absorber configuration of choice.
PL
W pracy przedstawiono model dwururowego amortyzatora samochodowego z zaworem o charakterystyce zależnej od amplitudy przemieszczenia. Zawór dodatkowy działa równolegle do zaworu głównego tłoka i pozwala na kształtowanie osiągów amortyzatora w zakresie małych przemieszczeń oraz średnich i wysokich częstotliwości wymuszenia. Model zawiera kluczowe zmienne geometryczne i materiałowe uwzględniające podstawowe osiągi zaworu w szerokim paśmie przemieszczeń i częstotliwości. Wyniki obliczeń zaprezentowano na płaszczyźnie fazowej siła-przemieszczenie w zakresie prędkości do 260 mm/s i częstotliwości wymuszenia do 12 Hz.
EN
The evaluation of possibility for recovering of part of vibration energy from automobile has been done in the article. One of the potential possibilities is utilization of fluid pressure in shock absorber to drive turbogenerator applying battery. It can be interesting to utilize air shock absorbers, in Gerard to possibility of direct outlet of expanded air into atmosphere - it can simplify the design of set recovering energy. The aim of researched presented in the article has been to evaluate possibility for recovering of energy from air shock absorber without deterioration of vibration damping level, which can be provided by hydraulic shock absorber. The scheme of proposed air shock absorber, its mathematical model, the results of calculation for pressure increasing in shock absorber during its piston motion, for different velocity of the piston have been shown in the article. The characteristics of hydraulic absorber and air one with energy recovering have been compared. The model of the wheel and the automobile mass connected with that wheel has been presented. Using such model the simulations of the wheel and of the automobile mass motion, for tasked velocity of automobile have been made. The model of road microprofile has been elaborated. Using the models the recovered energy in the 1 km road section has been calculated.
PL
W artykule dokonano oceny możliwości odzyskiwania części energii drgań pojazdu. Jedną z potencjalnych możliwości, jest wykorzystanie ciśnienia płynu w amortyzatorze do napędu turbogeneratora zasilającego akumulator. Interesujące wydaje się zastosowanie amortyzatorów pneumatycznych, z uwagi na możliwość bezpośredniego wyprowadzenia rozprężanego powietrza do atmosfery – co może ułatwiać konstrukcje układu odzyskującego energię. Celem przedstawianych w artykule badań jest ocena możliwości odzyskania energii z amortyzatora pneumatycznego, bez pogarszania poziomu tłumienia drgań, jaki zapewniają amortyzatory hydrauliczne. W artykule zamieszczono schemat proponowanego amortyzatora pneumatycznego, jego model matematyczny, wyniki obliczeń narastania ciśnienia w amortyzatorze w funkcji przemieszczenia jego tłoka, dla różnych prędkości tłoka. Porównano charakterystyki amortyzatorów: hydraulicznego i pneumatycznego z odzyskiwaniem energii. Zaprezentowano też model koła i związanej z nim masy samochodu. Przy użyciu tego modelu wykonano symulacje ruchu koła i masy samochodu dla zadanej prędkości ruchu pojazdu. Opracowano także model nierówności drogi. Przy pomocy wspomnianych modeli obliczono energię odzyskiwaną na drodze 1 km podczas ruchu pojazdu osobowego.
PL
W artykule przedstawiono wyniki badań amortyzatorów samochodowych przeprowadzonych na stanowisku indykatorowym. Celem tych badań było wyznaczenie ich własności lepko-sprężystych. Na tej podstawie zaproponowano strukturę modelu symulacyjnego, który został wdrożony w środowisku badań symulacyjnych Matlab/Simulink. Uzyskane wyniki badań symulacyjnych wykazują zgodność z rzeczywistym amortyzatorem w określonym przedziale zgodności, wynikającym z możliwości pomiarowych stanowiska.
EN
As part of the work being studied as a car shock-absorber on indicatory stand. The aim of research has been evaluation of the visco-elastic properties. On this basis, the proposed structure of the simulation model. The model has been implemented in an environment of simulation studies Matlab/Simulink. The results of simulation tests show compliance with the real shock-absorber. Conformance is a specified period of relevance arising from the possibility of measuring the stand.
EN
The paper presents method of diagnosing hydraulic shock absorber with wear and tear of piston packing. There are diagrams of shock absorbers for different cases of tightness reduction. Damping characteristics for different cases of reduction in tightness are shown at the end of article.
PL
W artykule przedstawiono diagnozowanie zuycia eksploatacyjnego uszczelnienia tłoczka samochodowego amortyzatora hydraulicznego. Zaprezentowano wykresy amortyzatorów dla rónych przypadków ubytku uszczelnienia. Na koncu artykuły umieszczono charakterystyki tłumienia dla amortyzatorów z rónym ubytkiem uszczelnienia.
EN
The paper presents results experimental investigations, which the aim was settlement of usefulness of two methods of non-stationary signal analyses: continuous wavelet transform and Wigner-Ville'a transform. Usefulness of those methods in diagnostic of vehicle shock absorbers was compared. The new diagnostic estimator was used in investigations. Damping elements are essential sets decisive of the drive safety of cars. Damping elements are most often hydraulic telescopic dampers. Tunings mechanical stimulant devices for vibrations in which an element enforcing is plate on which runs with wheel of investigated damper are in generally practical in Poland in research of built-up dampers in passenger cars . Used methods of multidimensional analyses are fitted for the identification of the single damage in the diagnostics of built-up dampers in the vehicle. CWT distribution of relative vibration acceleration, diagram of Wmax estimator values for oil volumes changes, cumulative diagram of Wmax estimator values, WV distribution of relative vibration acceleration, diagram of Wmax estimator values for oil volumes changes, cumulative diagram of estimator Wmax values are presented in the paper.
PL
W artykule przedstawiono wyniki badań eksperymentalnych, których celem było ustalenie przydatności dwóch metod analizy sygnałów niestacjonarnych: metodę ciągłej transformaty falkowej i metodę transformaty Wignera-Ville'a. Porównano przydatność w/w metod do analizy uszkodzeń amortyzatorów teleskopowych samochodów osobowych. Do celów porównawczych wykorzystano nowy estymator diagnostyczny. Istotnych zespołem decydującym o bezpieczeństwie jazdy samochodów są elementy tłumiące, którymi są najczęściej hydrauliczne amortyzatory teleskopowe. W Polsce powszechnie w badaniach amortyzatorów zabudowanych w samochodach osobowych stosuje się przestrajalne mechaniczne wzbudniki drgań, w których elementem wymuszającym jest płyta, na którą najeżdża samochód kołem z badanym amortyzatorem. Zastosowane metody analiz wielowymiarowych nadają się do identyfikacji pojedynczego uszkodzenia w diagnostyce amortyzatorów zabudowanych w pojeździe. Rozkład współczynników transformaty falkowej względnych przyśpieszeń drgań, wykres wartości estymatora Wmax przy zmianie objętości płynu, wykres zbiorczy wartości estymatora WmaXi rozkład współczynników WV sygnału względnych przyśpieszeń drgań, wykres zbiorczy wartości estymatora Wmax przy zmianie objętości płynu, wykres zbiorczy wartości estymatora Wmax są prezentowane w artykule.
first rewind previous Strona / 1 next fast forward last
JavaScript jest wyłączony w Twojej przeglądarce internetowej. Włącz go, a następnie odśwież stronę, aby móc w pełni z niej korzystać.