Wyniki wyszukiwania - BazTech

Ograniczanie wyników

3 Archives of Metallurgy and Materials

Znaleziono wyników: 3

Liczba wyników na stronie

Wyniki wyszukiwania

Wyszukiwano:
w słowach kluczowych: hot deformation activation energy

Sortuj według:

Ogranicz wyniki do:

Hot Deformation Activation Energy of Metallic Materials Influenced by Strain Value

Schindler I., Opěla P., Kawulok P., Sauer M., Rusz S., Kuc D., Rodak K.

Archives of Metallurgy and Materials

2021

Vol. 66, iss. 1

223--228

Suitable and complete sets of stress-strain curves significantly affected by dynamic recrystallization were analyzed for 11 different iron, copper, magnesium, titanium or nickel based alloys. Using the same methodology, apparent hot deformation activation energy Qp and Qss values were calculated for each alloy based on peak stress and steady-state stress values. Linear dependence between quantities Qp and Qss was found, while Qp values are on average only about 6% higher. This should not be essential in predicting true stress of a specific material depending on the temperature-compensated strain rate and strain.

Study of Hot Deformation Behavior of CuFe2 Alloy

Schindler I., Sauer M., Kawulok P., Rodak K., Hadasik E., Jabłońska M. Barbara, Rusz S., Ševčák V.

Archives of Metallurgy and Materials

2019

Vol. 64, iss. 2

701--706

Nil strength temperature of 1062°C and nil ductility temperature of 1040°C were experimentally set for CuFe2 alloy. The highest formability at approx. 1020°C is unusable due to massive grain coarsening. The local minimum of ductility around the temperature 910°C is probably due to minor formation of γ-iron. In the forming temperatures interval 650-950°C and strain rate 0.1-10 s-1 the flow stress curves were obtained and after their analysis hot deformation activation energy of 380 kJ·mol-1 was achieved. Peak stress and corresponding peak strain values were mathematically described with good accuracy by equations depending on Zener-Hollomon parameter.

Y Addition Effects on Hot Deformation Behavior of Cu-Zr Alloys with High Zr Content

Tian K., Tian B., Volinsky A. A., Zhang Y., Liu Y., Du Y.

Archives of Metallurgy and Materials

2018

Vol. 63, iss. 2

875--882

Isothermal hot compression experiments were carried out using the Gleeble-1500D thermal mechanical simulator. The flow stress of the Cu-1%Zr and Cu-1%Zr-0.15%Y alloys was studied at hot deformation temperature of 550°C, 650°C, 750°C, 850°C, 900°C and the strain rate of 0.001 s-1, 0.01 s-1, 0.1 s-1, 1 s-1, 10 s-1. Hot deformation activation energy and constitutive equations for two kinds of alloys with and without yttrium addition were obtained by correlating the flow stress, strain rate and deformation temperature. The reasons for the change of hot deformation activation energy of the two alloys were analyzed. Dynamic recrystallization microstructure evolution for the two kinds of alloys during hot compression deformation was analyzed by optical and transmission electron microscopy. Cu-1%Zr and Cu-1%Zr-0.15%Y alloys exhibit similar behavior of hot compression deformation. Typical dynamic recovery occurs during the 550-750°C deformation temperature, while dynamic recrystallization (DRX) occurs during the 850-900°C deformation temperature. High Zr content and the addition of Y significantly improved Cu-1%Zr alloy hot deformation activation energy. Compared with hot deformation activation energy of pure copper, hot deformation activation energy of the Cu-1%Zr and Cu-1%Zr-0.15%Y alloys is increased by 54% and 81%, respectively. Compared with hot deformation activation energy of the Cu-1%Zr alloy, it increased by 18% with the addition of Y. The addition of yttrium refines grain, advances the dynamic recrystallization critical strain point and improves dynamic recrystallization.