Wyniki wyszukiwania - BazTech

1

Verification of sensors for yaw rate and lateral acceleration in car ESP system

Gajek Andrzej, Janczur Robert, Pieniążek Wiesław, Wolak Stanisław

Archiwum Motoryzacji

|

2020

|

Vol. 88, nr 2

61--76

EN

This study analyzed the possibilities to validate the indications of sensors for yaw rate and lateral acceleration within the scope of extended diagnostic routine of the car ESP system at Vehicle Inspection Stations. The stand tests were performed using the reference sensors and a standard diagnostic tester. The comparison of the yaw rate and lateral acceleration results obtained from the working sensor under examination, recorded with the Vbox unit, and the results from the reference sensor demonstrated a good conformity both in quality and quantity. But these tests demonstrated also a pure conformity (both in quality and quantity) with runs obtained from tester. The Root Mean Square (RMS) was used as factor of qualitative estimation. These inconveniences were caused by in sampling frequency incompatibility and lack of recording synchronization for signals from the tester and from reference sensors. The question of primary importance is a firmware modification for selected testers. Such a tester should be able to record signals from a reference sensor and have a set sampling frequency for signals from a working sensor. On the basis of already carried out research analyses the suggested frequency should be no lower than approximately 10 Hz. It resulted from a spectral analysis carried out for possessed runs maintaining the Nyquist limit frequency.

2

Multifaceted diagnostic inference process for identifying the causes of self-ignition engine faults resulting from PM sediments

Cieślikowski B., Cygnar M., Jakóbiec J.

Combustion Engines

|

2017

|

R. 56, nr 1

186--190

EN

Optimization of the fuel combustion process in a self-ignition engine with the multi-stage HPCR injection system sets the main trends in research on the thermodynamic stability of fuels, and the mechanisms of PM formation. The stages were indicated of the multifaceted diagnostic inference on the causes of failures of a turbocharger with variable geometry (VTG) which occur as a result of PM sedimentation in the nozzle area. An evaluation of the engine performance was conducted using a dedicated tester and an additional recording of the injector coil current characteristics with parallel readings of the fuel pressure variation in the reservoir. The indicated procedure established the underlying cause of the VTG compressor failure despite the absence of a recorded error code.

3

Diagnostic testers operating on the basis of the FAM-C method

Gębura A., Pietnoczko B., Tokarski T.

Diagnostyka

|

2016

|

Vol. 17, No. 3

87--94

EN

The article discusses the design and principles of operation of three diagnostic testers constructed by the authors of this study, intended for three, different aircraft propulsion units. These design have one common way of processing the original diagnostic signal - they use one FAM-C method. This method is based on natural processing of the rotational speed fluctuations of individual kinematic cells of the propulsion unit, by the on-board generator into frequency modulations. The method, thanks to its properties, is extremely beneficial for the automatic digital diagnostic processing. The tester can be connected at any, convenient for the crew, location of the power grid, away from dangerous zones of the aircraft.

PL

W artykule omówiono konstrukcję i zasadę działania trzech testerów diagnostycznych skonstruowanych przez autorów niniejszego opracowania przeznaczonych do trzech różnych lotniczych zespołów napędowych. Konstrukcje te łączy jeden wspólny sposób przetwarzania pierwotnego sygnału diagnostycznego - wykorzystują one metodę FAM-C. Metoda ta bazuje na naturalnym przetwarzaniu wahań prędkości obrotowej poszczególnych ogniw kinematycznych zespołu napędowego przez prądnicę pokładową na modulacje częstotliwości. Metoda dzięki swym szczególnym właściwościom jest wyjątkowo korzystna dla cyfrowego automatycznego przetwarzania diagnostycznego. Tester może być przyłączony w dowolnym, dogodnym dla obsługi miejscu sieci elektroenergetycznej, z daleka od niebezpiecznych stref statku powietrznego.