Preferencje help
Widoczny [Schowaj] Abstrakt
Liczba wyników
Powiadomienia systemowe
  • Sesja wygasła!

Znaleziono wyników: 7

Liczba wyników na stronie
first rewind previous Strona / 1 next fast forward last
Wyniki wyszukiwania
Wyszukiwano:
w słowach kluczowych:  cold-rolling
help Sortuj według:

help Ogranicz wyniki do:
first rewind previous Strona / 1 next fast forward last
EN
The article presents the effect of cold-rolling welded joints in railway lines on their mechanical and tribological properties. Welded joints of high-manganese Hadfield cast steel (L120G13) and normalized rail steel (R350HT) with austenitic steel coupling (X12CrNi17-7) were tested. The conducted tests allowed the hardness profile of the treated surfaces to be studied, as well as the wear resistance and coefficient of friction. The results were compared to the base materials and exhibited hardness enhancement in 80% of cold-rolled surfaces and, moreover, reduced abrasive wear resistance.
PL
W pracy przeprowadzono analizę wpływu umocnienia statycznego metodą nagniatania naporowo-tocznego na własności mechaniczne oraz tribologiczne złącza zgrzewanego staliwa Hadfilda L120G13 ze stalą szynową R350HT nieulepszoną cieplnie z wykorzystaniem przekładki ze stali austenitycznej X12CrNi17-7. Wyniki badań pozwoliły na określenie rozkładu twardości, wskaźnika zużycia objętościowego oraz współczynnika tarcia. Testy przeprowadzono na próbkach przed i po umacnianiu statycznym. Testy wykazały zwiększenie twardości umacnianych powierzchni nawet o 80% oraz odporności na zużycie ścierne badanych materiałów.
PL
Omawiany jest przypadek obserwacji zróżnicowania stanu strukturalnego po walcowaniu na zimno i wyżarzaniu stopu 3003, które wynika ze zmiany temperatury końca walcowania na gorąco. Zróżnicowanie to jest źródłem niestabilności skutków całego procesu technologicznego i w konsekwencji można wskazywać, iż ma bezpośredni wpływ na trudności z uzyskaniem oczekiwanych własności użytkowych wyrobu.
EN
The author discuses the case when differentiation of the structural state is observed after cold rolling and annealing of 3003 alloy, which occurs as a result of the temperature change at the end of hot rolling. This differentiation is responsible for the instabilility of the results of the entire technological process and, as a consequence, it can be interpreted as indicating that it is directly connected with the difficulties in obtaining the expected functional properties of the product.
PL
Przedstawiono wyniki badań nad optymalizacją procesu walcowania na zimno rur miedzianych Cu-DHP oraz miedzioniklowych MNŻ101 w walcarce pielgrzymowej KPW75VMRK. Analiza wyników tych badań pozwoliła określić warunki eksploatacji narzędzi do pielgrzymowania pod kątem zwiększenia ich żywotności. Stwierdzono negatywne wzajemne działanie korozji i koncentracji naprężeń na trwałość powierzchni wykroju (a w konsekwencji na jakość powierzchni walcowanych rur) wskazując kierunki poprawy sposobu przygotowania narzędzi.
EN
Results of works on optimisation of the process of cold rolling the Cu-DHP copper tubes and the MNŻ101 copper-nickel tubes using the KPW75VMRK pilger mill have been presented. Analysis of the results obtained was made in order to determine working conditions of the pilger mill tools so as to increase their life. Negative effect of both corrosion and stress concentration on the life of a roll pass surface, and consequently on the surface quality of the rolled tubes, have been found indicating the necessity to improve methods for the tools preparation.
EN
A CuA15 single crystal with the initial orientation of (110)[001] was rolled with 80% reduction in thickness and subsequently recrystallized. First recrystallized grains appeared in the sample annealed at 335 degrees centigrade while the sample annealed at 385 degrees centigrade was fully recrystalized. The recrystallization texture showed following components: {112}<238>, {135}<479> and {125}<259>. Only the strongest component {112}<238> could be produced according to the oriented growth theory.
EN
Structural investigation and texture measurements were conducted on a cold-rolled Ni-25%Mo-8%Cr alloy subjected to recrystallization. Prior to rolling, the examined material was in three different conditions: as-solution treated, aged at 650 degrees centigrade and aged at 710 degrees centigrade conditions. Aged samples contained precipitates of the long range ordered Ni2(Mo,Cr) phase which size depend strongly on aging temperature. The applied deformations were 20, 40, 60 and 80% . Recrystallization annealing was carried out at temperature range of 750 degrees centigrade - 950 degrees centigrade for 1 hour. The presence of the ordered particle in the deformed state hampered recrystallization. The recrystallization texture was much weaker than the deformation one but retained its main features.
EN
The intensive twinning and crystal break-up into deformation bands occurred during cold rolling of a Cu-5%Al single crystal with the initial orientation (100)[011]. Due to rotation of the initial orientation and intensive twinning large areas with the {110}<001> orientation were formed close to the rolled surfaces. Relatively uniform microstructure consisted of mutually intersecting dislocation bands featured areas of such orientation. Shear bands appeared close to the central layer of the rolled material in the regions with the large density of deformation twins parallel to the rolling plane. Cells composing shear bands had usually orientations near {110}<001>.
EN
In this work the results of the texture investigations in cold deformed sintered powder iron strips made from powder WPL-200 type are presented. Textures of starting materials with different densities were measured. These materials were deformed by rolling in deformation range from 0 to 40%. Weak textures were found in powder iron strips no mater what was their starting density.
first rewind previous Strona / 1 next fast forward last
JavaScript jest wyłączony w Twojej przeglądarce internetowej. Włącz go, a następnie odśwież stronę, aby móc w pełni z niej korzystać.