Preferencje help
Widoczny [Schowaj] Abstrakt
Liczba wyników

Znaleziono wyników: 7

Liczba wyników na stronie
first rewind previous Strona / 1 next fast forward last
Wyniki wyszukiwania
Wyszukiwano:
w słowach kluczowych:  carburized layers
help Sortuj według:

help Ogranicz wyniki do:
first rewind previous Strona / 1 next fast forward last
PL
Celem pracy była ocena zróżnicowania twardości próbek nawęglanych w tym samym procesie - teoretycznie w tych samych warunkach. Zakładano uzyskanie stałej grubości warstwy 1,2 mm i trzech nominalnych twardości 700 HV0,5, 740 HV0,5, 780 HV0,5. Wykonano pomiary twardości od HV0,1 do HV10 i badania metodą prądów wirowych. Szczególną uwagę poświęcono pomiarom mikrotwardości powierzchniowej HVO,1. Na stosunkowo malej powierzchni kontrolnej stwierdzono duże zróżnicowanie wyników pomiarów twardości czterech „jednakowych "powierzchni. Po zwiększeniu liczby oznaczeń z 5 do 13 uległy zmianie wartości średnich oraz wzrost odchylenia standardowego. Wykonane pomiary wskazują na celowość stosowania więcej, niż 5 punktów pomiarowych dla danej próbki wymaganych przez normy i procedury badań. Pomiarami HVO,1 wykryto skokową zmianę twardości o 10 jednostek i powtarzanie tych wartości w różnych próbkach, co sygnalizuje przydatność oznaczenia przy charakteryzowaniu struktury warstwy. Stwierdzono korelację między pomiarami twardości a oznaczeniami wiroprądowymi. Zastosowanie uśredniających oznaczeń wiroprądowych mogłoby zwiększyć prawdopodobieństwo eliminowania wadliwych elementów i podnieść poziom jakości wyrobów.
EN
The aim of the paper was to evaluate the hardness differentiation of the samples carburized in the same process - theoretically under the same conditions. It was assumed to obtain a constant layer thickness of 1.2 mm and three nominal hardness values: 700 HV0.5, 740 HV0.5, 780 HV0.5. Hardness measurements from HV0.1 to HV10 and eddy current tests were carried out. Particular attention was paid to the measurements of HV0.1 surface microhardness. On the relatively small control surface, a large diversity of hardness measurement results was found for four "identical" surfaces. After increasing the number of determinations from 5 to 13, the mean values changed and the standard deviation increased. The carried out measurements indicate the desirability of using more than 5 measuring points for a given sample required by test standards and research procedures. The HV0.1 measurements revealed a step change in hardness by 10 units and repeating these values in different samples, which signals the usefulness of the determination when characterizing the structure of the layer. A correlation was found between hardness measurements and eddy current tests. The use of averaging eddy current tests could increase the probability of eliminating defective components and increase the level of product quality.
PL
Nieniszcząca metoda prądów wirowych ma zastosowanie do badań metali i ich stopów przewodzących prąd. Metodą prądów wirowych można wykrywać obecność pęknięć, oceniać zmiany struktury, określać, grubości warstw przypowierzchniowych. Celem pracy była ocena przydatności układu kontrolno-pomiarowego typu Wirotest oraz sond do szybkiej kontroli jakości całych partii wyrobów. Zebrane doświadczenia i przedstawione wyniki oznaczeń metodą prądów wirowych, porównywanych z pomiarami twardości potwierdziły ich korelację. Metoda może być przydatna do wstępnej selekcji, a także kontroli jakości 100% detali, zwłaszcza nawęglanych.
EN
The non-destructive method of eddy currents is applicable to tests of metals and their conducting alloys. The method of eddy currents can detect the presence of cracks, evaluate structural changes, and determine the thickness of surface layers. The purpose of the paper was to assess the suitability of the Wirotest control - measurement system and the probes for fast quality control of whole batches of products. The collected experiments and the presented results of eddy current tests, compared to hardness measurements, confirmed their correlation. The method can be useful for the initial selection as well as for the 100% quality control of details, especially carburized.
EN
Structures of carburized layers after the surface saturation process in gaseous, liquid or solid medium and after subsequent heat treatment (hardening and low-temperature tempering) consist mainly of high carbon plate martensite with a certain portion of retained austenite. The presence of retained austenite (RA) in carburized layers is mostly considered as undesirable because it decreases hardness of the hardened layer and furthermore, a spontaneous conversion to a ferritic-carbide mixture of a bainitic type, accompanied by a change of properties, dimensional instability and the local increase in internal stress with the possible formation of cracks, can occur. The proportion of retained austenite is, therefore, a significant characteristics of the quality of hardened layers. This work deals with the evaluation of the volume fraction of retained austenite in carburized layers using image analysis on metallographic images.
PL
Przedmiotem pracy jest opracowanie sposobu wykonania pomiaru i urządzenie do nieniszczącego pomiaru grubości warstwy nawęglanej oraz twardości powierzchniowej w uzębieniu koła zębatego metodą prądów wirowych. Celem pracy jest umożliwienie przeprowadzenia powtarzalnego pomiaru, uwzględniając przy tym skomplikowaną geometrię koła zębatego. Zastosowany nieniszczący pomiar grubości warstwy nawęglanej oraz twardości powierzchniowej uzębienia koła zębatego metodą prądów wirowych polegał na tym, że mierzono w jednym cyklu pomiarowym grubość warstwy nawęglanej na dnie wrębu i na powierzchni bocznej zęba oraz twardość powierzchniową na powierzchni bocznej zęba. Do badanych miejsc przykładano prostopadle do powierzchni zestaw trzech czujników pomiarowych o różnych częstotliwościach wzbudzenia. Zestaw ten tworzył sondę zespoloną. Opracowana metoda i zestaw pomiarowy zapewniają uzyskanie stabilności, powtarzalności i dokładności pomiaru, a także eliminują błędy przypadkowe w określonych punktach pomiaru na zębach.
EN
The subject matter of this paper is the development of a measurement technique and a device for a non-destructive measurement of the thickness of a carburized layer and the surface hardness in the toothing of a gear wheel, by means of the eddy current method. The aim of this work is to make it possible to carry out the repeatable measurement, taking into account the complex geometry of the gear wheel. The applied technique of a non-destructive measurement of the thickness of the carburized layer and the surface hardness of the gear wheel teething by means of the eddy current method consisted in the measurement of the carburized layer thickness in a single measurement cycle at the bottom of the tooth space and on the tooth flank and the measurement of the surface hardness on the tooth flank. A set of three sensors with different excitation frequencies was applied perpendicularly to the tested places. This set of sensors created a complex probe. The developed method and the measurement equipment ensure the achievement of stability, repeatability and accuracy of the measurement, and also eliminate the random errors in the measurement of the specific points on the teeth.
EN
In the paper the results of carburized layers depth investigation, based on real carburizing processes and numerical carburizing model simulation, were presented. Obtained results taking in account assumed numerical model, demonstrates good agreement with experimental investigations.
PL
W pracy przedstawiono wyniki badań grubości warstw nawęglonych oparte na rzeczywistych procesach przeprowadzonych na stanowisku do nawęglania próżniowego oraz symulacji numerycznego modelu nawęglania. Otrzymane w oparciu o założony model numeryczny wyniki pokazują dużą zgodność z weryfikacją doświadczalną.
EN
The paper presents the results of laser heat treatment (LHT) of the borided layers produced on the 40H steel (0.43 %C, 1.02 %Cr). The LHT has been carried out by CO2 laser beam. The microstructure, microhardness and wear resistance have been studied after LHT of borided layers. The improved properties of these layers have been found in comparison with borided or carburized layers after conventional heat treatment.
PL
W pracy zaprezentowano wyniki badań nad laserową obróbką cieplną (LOC) warstw borowanych wytwarzanych na stali 40H (0.43 %C, 1.02 %Cr). LOC przeprowadzono przy zastosowaniu lasera CO2. Badano mikrostrukturę, twardość i odporność na zużycie przez tarcie warstw borowanych poddanych LOC. Stwierdzono podwyższenie właściwości użytkowych w porównaniu do warstw borowanych i nawęglanych poddawanych tradycyjnej obróbce cieplnej.
PL
Stosowane w technice chłodzenia syntetyczne chłodziwa mają największe perspektywy rozwoju. W miarę doskonalenia ich własności technologicznych i rozszerzenia asortymentu odmian, będą one przypuszczalnie eliminowały stopniowo oleje mineralne. W pracy przedstawiono wyniki badań wpływu wybranych syntetycznych ośrodków chłodzących z grupy poliglikoli oxyalkilenowych (PAG) na skład fazowy i własności użytkowe zahartowanych warstw nawęglonych lub azotonawęglanych wytworzonych w stalach konstrukcyjnych. W ramach przeprowadzonych badań porównano tradycyjne ośrodki chłodzące takie jak woda, olej z reprezentantami ośrodków z grupy poliglikoli oxyalkilenowych (PAG). Wyniki badań wskazują, że chłodziwa z grupy PAG pozwalają na uzyskanie dobrej korelacji pomiędzy określoną strukturą, a podwyższonymi własnościami użytkowymi warstw nawęglonych lub azotonawęglanych wytworzonych w stalach konstrukcyjnych.
EN
Synthetic quenching media have the greatest perspectives of development. As improvement of their technological properties and widening of assortment proceeds, they presumably will eliminate gradually mineral oils. In the work the results of the researches on influence of selected synthetic quenching media from the group of poly-alkylene-glycol (PAG) on phase composition and useful properties of hardened carburized or carbonitrided layers produced on constructional steels are presented. In the research the traditional quenching media such as water and oil have been compared with representatives of media from the group poly-alkylene-glycol (PAG). Results of research show, that media from the PAG group permit obtaining a good correlation between structure and useful properties carburized or carbonitrided layers produced on constructional steels.
first rewind previous Strona / 1 next fast forward last
JavaScript jest wyłączony w Twojej przeglądarce internetowej. Włącz go, a następnie odśwież stronę, aby móc w pełni z niej korzystać.