Preferencje help
Widoczny [Schowaj] Abstrakt
Liczba wyników

Znaleziono wyników: 17

Liczba wyników na stronie
first rewind previous Strona / 1 next fast forward last
Wyniki wyszukiwania
Wyszukiwano:
w słowach kluczowych:  RPC
help Sortuj według:

help Ogranicz wyniki do:
first rewind previous Strona / 1 next fast forward last
EN
In this study, a new reactive powder concrete (RPC) was developed, with environmentally friendly typical RPC components obtained from ground quartz substituted by the waste glass. In this manner, the carbon footprint and final cost are minimized by replacing aggregates and reducing cement. A challenge in this study was using high-celite phase available cement and avoiding the alkali-silica reaction. The Box–Wilson design and Derringer–Suich optimization were used to create an RPC mixture with a low cement content and high-volume waste glass dosage that achieved a compressive strength of more than 120 MPa. It was demonstrated that having all ground waste glass particles smaller than 1000 µm is not sufficient to prevent the alkali-silica expansion. Furthermore, commercially available cement with a high celite proportion had a modest beneficial influence on the compressive strength at an early-age but a significant detrimental impact on the RPC’s compressive strength at 28 days. Finally, the current study proved the potential of manufacturing an RPC that satisfied the strength threshold criterion while utilizing a local cement with over 12% celite and a substantial volume of waste glass powder comprising more than half of the RPC weight.
EN
In this study, ten reactive powder concrete (RPC) specimens confined by high-strength spirals loaded over a limited area are used to investigate their behaviour and determine their local bearing capacity. The crack, wedge, and failure characteristics of RPC are discussed based on tests and simulation. The index of pressure versus deformation is used to evaluate the loading stages. The ratio of the cracking load to the ultimate load varies from 34 to 60%. A wedge pyramid is formed ahead of the bearing plate when approaching the ultimate load; thereafter, it slips downward, splitting the concrete below. The high-strength spirals did not yield even under the ultimate load. According to the test data, all the existing models for predicting the local bearing capacity are nonconservative. In this case, the effect of the actual stress caused by high-strength spirals is considered to further modify the existing calculation models when high-strength spirals are used, and a simple empirical equation for calculating the local bearing capacity of the RPC is developed. The equation and the models modified as described are verified experimentally.
EN
Reactive powder concrete (RPC), due to its characteristic composition with reduced water quantity, often below a stoichiometric ratio, the addition of pozzolana usually close to or above 20% of the weight of cement and a significantly reduced inclusion rate compared to normal or high performance concrete, has a different nature of the interfacial transition zone between the micro aggregate grains and the binder matrix. Due to the significant influence of RPC curing conditions on the morphology of the interfacial transition zone, the analysis included composites cured in water of Tmax=20°C, subject to low-pressure steam curing Tmax=90°C and autoclaved at Tmax=250°C. The paper presents a qualitative assessment of the interfacial transition zone in reactive powder concretes with the use of a scanning microscope with the use of linear EDS and quantitative analysis by means of stereological analysis of the image obtained with the use of a BSE detector. The results of the study unequivocally confirm the lack of portlandite crystallisation at the phase interface and the different phase composition in the interfacial transition zone in relation to the mean mass composition.
PL
Ewolucję opisu strefy przejściowej w kompozytach cementowych prześledził Kurdowski w publikacji „Chemia Cementu i Betonu”, gdzie scharakteryzował jej ogólnie przyjęte modele zróżnicowane pod względem występujących kolejno po sobie stref, jak i pod względem ich składu fazowego. Ponadto rozwój metodyki badań strefy przejściowej pozwala obecnie coraz ściślej opisywać właściwości oraz budowę tej newralgicznej części cementowych kompozytów ziarnistych. Stosuje się tutaj najczęściej metodę mikroskopii zarówno optycznej jak i skaningowej wraz ze stereologiczną analizą obrazu, analizę EDS, XRD, a także w celu rozpoznania różnic we właściwościach mechanicznych względem kruszywa i matrycy stosuje się badania metodą nanoindentacji. W przypadku tradycyjnych kompozytów cementowych strefa przejściowa odgrywa ważną rolę w kształtowaniu ich cech mechanicznych ze względu na obszar, w którym najczęściej dochodzi do zainicjowania rys w obciążonym materiale. Z tego względu, jedną z podstawowych idei komponowania składu kompozytów BPR jest homogenizacja tekstury kompozytu, mająca bezpośredni związek z ujednorodnieniem rzeczywistych naprężeń panujących w obciążonym materiale. Godycki-Ćwirko tłumaczy, jak intensywnie na wartość naprężeń rzeczywistych wpływa: wielkość inkluzji, wzajemna odległość pomiędzy jej ziarnami oraz różnica w odkształcalności inkluzji względem matrycy. Ponadto, na charakter strefy przejściowej mają także warunki dojrzewania kompozytu. Z tego powodu w części badawczej niniejszego artykułu scharakteryzowano strefę przejściową pomiędzy matrycą spoiwową i mikrokruszywem kwarcowym w betonach z proszków reaktywnych dojrzewających w zróżnicowanych warunkach hydrotermalnych tj. w wodzie, poddane niskoprężnemu naparzaniu w temperaturze 90°C oraz autoklawizacji w temperaturze 250°C. Warunki te wpływają na reaktywność poszczególnych składników kompozytu i tym samym na skład fazowy strefy przejściowej. W badaniach wykorzystano standardowy skład mieszanek betonów z proszków reaktywnych, które po dojrzewaniu w wyżej wymienionych warunkach hydrotermalnych zostały poddane obserwacjom mikroskopowym SEM wraz z analizą EDS. Badania jakościowe zostały zrealizowane na powierzchni trzech losowo wybranych ziaren piasku kwarcowego, każdorazowo realizując pięć analiz liniowych EDS ukierunkowanych prostopadle do powierzchni ziarna. Pozwoliły one na wyznaczenie proporcji liczby atomów pierwiastków Ca, Si, Al i Fe w całym przyjętym zakresie długości linii i tym samym w każdym jej punkcie z rozdzielczością około co 0,05 μm. Na tej podstawie naniesiono chmurę punktów pomiarowych w układzie współrzędnych Ca/Si – Al+Fe/Ca, gdzie zaznaczono także obszary występowania możliwych w kompozycie faz tj. C-S-H, CH, C3S, AFm.
EN
The influence of replacement 30% of cement by mineral admixtures (fly ashes or granulated blast furnace slag) on the RPC strength was presented. The tests were accomplished after 28 days of curing. The analysis of the results has shown that the concrete RPC 3, containing 30% of granulated blast furnace slag, achieved the highest compressive strength. The addition of steel fibres increases bending strength of RPC.
5
Content available remote Two-scale modelling of reactive powder concrete. Part II numerical simulations
EN
This article is the second part of a series about two-scale modelling of reactive powder concrete (RPC). In the first part [2] a method of modelling RPC microstructure was presented, the boundary value problem of mechanics for a representative cell at the micro scale was formulated and solved. In this part we will consider a method for determining material parameters at the macro level, and describe a technique of enforcement of boundary conditions upon an RVE as well as illustrate the theoretical considerations with results of numerical simulations. In the third part of the series we will present the validation of the proposed numerical model, based on the computational simulations of full size beams made of two RPC mixtures and own laboratory testing of the beams.
EN
This article is the third and final part of a series about two-scale modelling of reactive powder concrete in the linear range. In the first part [1] a method of modelling RPC microstructure was presented, the boundary value problem of mechanics for a representative cell at the micro scale was formulated and solved. In the second part [2] a method for determining material parameters at the macro level was shown, a technique for enforcing boundary conditions upon an RVE was described, and the results of numerical simulations were presented. In this part we will present the results of laboratory tests of full-size beams made from two RPC mixtures, the results of numerical simulations of these beams and the validation of the proposed numerical model.
7
Content available remote New Generation Cementitious Composites with fibres – properties and application
EN
The paper presents the properties of new generation cementitious composites with fibres, such as "bendable concrete" (ECC, Engineered Cementitious Composites) (plastic, not brittle but resistant to cracking material) with the addition of polyvinyl alcohol (PVA) fibres, high performance concrete (HPC) with glass fibres, reactive powder concrete (RPC) (characterized by ultra-high compressive strength, above 200 MPa) with short steel fibres. The detailed characteristics of the composition of the cement matrix and the role of fibres in the formation of the composite properties are described. Various applications of the composites as structural and architectural materials are also given.
PL
W artykule przedstawiono właściwości najnowszej generacji kompozytów cementowych z dodatkiem włókien, m.in. "betonów zginalnych" (ECC) (plastycznych, a nie kruchych przy zginaniu, odpornych na pękanie) z włóknami polialkoholowinylowymi (PVA), wysokowartościowych betonów (HPC) z włóknami szklanymi, betonów z proszków reaktywnych (RPC) (cechujących się ultrawysoką wytrzymałością na ściskanie − powyżej 200 MPa) z krótkimi włóknami stalowymi. Szczegółowo scharakteryzowano skład matrycy cementowej oraz opisano rolę, jaką spełniają włókna w kształtowaniu właściwości kompozytu. Pokazano możliwości zastosowania kompozytów jako materiałów konstrukcyjnych oraz architektonicznych.
8
Content available TRIDAQ Systems in HEP Experiments at LHC Accelerator
EN
The paper describes Trigger and Data Acquisition (TRIDAQ) systems of accelerator experiments for High Energy Physics. The background for physics research comprises assumptions of the Standard Model theory with basic extensions. On this basis, a structure of particle detector system is described, with emphasis on the following functional blocks: Front-End Electronics, Trigger and DAQ systems. The described solutions are used in the LHC experiments: ATLAS, ALICE, CMS and LHCb. They are also used in other accelerator experiments. Data storage and processing functionality is divided into two hardware systems: Trigger and Data Acquisition, that are dependent on each other. High input data rate impose relevant choices for the architecture and parameters of both systems. The key parameters include detailed system structure and its overall latency. Trigger structure is defined by the physics requirements and the storage capability of DAQ system. Both systems are designed to achieve the highest possible space and time resolution for particle detection. Trigger references are reviewed [1]–[39] as well as chosen accelerator research efforts originating in this country [40]–[83].
EN
The article is the first part of a series concerned with the modelling of reactive powder concrete by using a numerical homogenization technique. This technique is a multi-scale modelling approach. Specifically, in this paper a two scale modelling concept was applied. A model of reactive powder concrete (RPC) is considered whose behaviour on the macro scale is described on the basis of the phenomena occurring in the microstructure of the material. This approach provides the ability to take into account some complex phenomena occurring in the microstructure and their influence on the macroscopic physical and mechanical properties of the material. The method does not require knowledge of the constitutive equation parameters at the macro level. These are determined implicitly for each load increment on the basis of numerical model of a representative volume element,(RVE), which reflects the geometrical layout of particular material phases, their constitutive relations and mutual interactions. In this paper the linearly elastic behaviour of each constituent material is assumed within the small strain range. In solving the boundary value problems formulated on the RVE for RPC, the finite element method was utilized. A number of numerical test examples were solved which illustrate the influence of inhomogeneities on the overall response.
PL
Artykuł jest pierwszą częścią pracy dotyczącej modelowaniu betonów z proszków reaktywnych przy zastosowaniu numerycznej homogenizacji. Technika ta jest podejściem wielkoskalowego modelowania. W tym konkretnym przypadku modelowania dwuskalowego. Zachowanie modelu betonu typu RPC w skali makro (skala punktu materialnego, poziom opisu fenomenologicznego) opisywane jest na podstawie zjawisk zachodzących w mikrostrukturze materiału (mikroskala). Takie podejście daje możliwość uwzględnienia szeregu zjawisk zachodzących w mikrostrukturze na właściwości fizyczne i mechaniczne materiału. Na przykład wpływ mikropęknięć na wytrzymałość betonu. Nie bez znaczenia jest fakt, że metoda nie wymaga znajomości równań konstytutywnych w skali makro, związki te są wyznaczane w sposób niejawny dla każdego przyrostu obciążenia na podstawie numerycznego modelu reprezentatywnego elementu objętościowego RVE. Do wyznaczenia niejawnych związków fizycznych w makroskali niezbędna jest znajomość geometrii mikrostruktury, równań konstytutywnych na poziomie skali mikro oraz ich parametrów. W tej pierwszej części pracy ograniczono się do sformułowania i rozwiązania zagadnienia brzegowego na poziomie mikroskali dla zadanych makronaprężeń na brzegu RVE. Opracowano własny program komputerowy, który generuje w sposób losowy mikrostrukturę RPC i rozwiązuje problem brzegowy zdyskretyzowany metodą elementów skończonych. Praca zawiera wyniki obliczeń zadań testowych.
PL
Celem pracy było przeprowadzenie analizy orientacji scen stereo w zależności od liczby wykorzystanych fotopunktów, zbadanie wpływu odchyleń standardowych biasu na wyniki orientacji oraz ocena dokładnościowa numerycznych modeli terenu i ortoobrazów wygenerowanych z wysokorozdzielczych zobrazowań satelitarnych pozyskanych z satelitów GeoEye-1 oraz Ikonos-2. W literaturze anglojęzycznej tematykę biasu, czyli poprawki wynikającej z podniesienia dokładności korekcji RPC (ang. Rational Polynomial Coefficient), poruszają w swoich artykułach C. S. Fraser oraz H. B. Hanley. Podejmują oni głównie problem orientacji wysokorozdzielczych zobrazowań satelitarnych oraz wpływ biasu na jej wynik. W Polsce na temat ten napisano niewiele referatów, dlatego też nasz zespół zdecydował się na przeprowadzenie niezbędnych badań i analiz. Satelita GeoEye-1, po umieszczeniu na orbicie we wrześniu 2008 roku, osiągnął swoją pełną zdolność operacyjną już w lutym 2009 roku. Jako jeden z pierwszych dostarczał zobrazowań o półmetrowej rozdzielczości przestrzennej w zakresie panchromatycznym. Dlatego też przedmiotem badań były dwie panchromatyczne stereopary - jedna pozyskana właśnie z satelity GeoEye-1, a druga z Ikonos-2 wystrzelonego w 1999 roku. Zarówno Ikonos-2, jak i GeoEye-1 są reprezentatywnymi satelitami dostarczającymi wysokorozdzielczych danych obrazowych. Charakteryzują się podobnymi parametrami technicznymi, własnościami orbity, pozyskują zobrazowania w trybie panchromatycznym i wielospektralnym, a także dostarczają zobrazowań o rozdzielczości przestrzennej w zakresie panchromatycznym poniżej 1 metra. Opracowane stereopary przedstawiają miasto Hobart (Australia) oraz jego okolice. Jest to teren zróżnicowany topograficznie, obejmujący zatokę, obszar silnie zurbanizowany oraz zalesione pasmo górskie. Zakres wysokości obejmuje przedział około od 0 do 1300 m. Zróżnicowanie wysokościowe opracowywanego terenu miało znaczący wpływ na jakość finalnych produktów fotogrametrycznych, co również zostało przeanalizowane. Do opracowania wykorzystano część osnowy fotogrametrycznej pomierzonej w 2004 roku techniką GPS. Do orientacji użyto 19 fotopunktów. Istotą poniższych rozważań było porównanie wyników orientacji przeprowadzonej przy różnej liczbie fotopunktów, z zachowaniem stałej konfiguracji punktów kontrolnych. Na podstawie przeprowadzonej analizy określona została liczba fotopunktów właściwa dla orientacji każdej stereopary. Kolejnym zagadnieniem była korekcja biasu w RPC. Przeprowadzona została analiza zależności zachodzących pomiędzy obrazem a terenem podczas orientacji zobrazowań oraz opisano równania poprawek służące eliminacji biasu przed i po orientacji zewnętrznej, przeprowadzonej na podstawie oryginalnych RPC. Istotną kwestią było określenie zależności między wartością błędu RMS (ang. Root Mean Square) wykonanej orientacji a odchyleniem standardowym biasu w kierunkach osi układu obrazowego (wiersza i kolumny - ng. line i sample). Po określeniu liczby fotopunktów odpowiedniej do wykonania orientacji oraz najkorzystniejszych wartości odchyleń standardowych biasu w obu kierunkach, wygenerowane zostały numeryczne modele terenu. Zastosowano cyfrową korelację obrazów metodą ABM (ang. Area Based Matching). Wynikowy rozmiar pikseli numerycznych modeli terenu generowanych z obu stereopar wyniósł 10 m. Powstałe modele przebadano pod kątem dokładności pionowej położenia punktu, poprzez porównanie wysokości pomierzonych techniką GPS z tożsamymi wysokościami pomierzonymi na danym modelu wysokościowym. Kolejnym etapem było wygenerowanie ortoobrazów z pojedynczych zdjęć ze stereopary oraz przeanalizowanie ich dokładności. Wymiar oczka generowanych produktów fotogrametrycznych wyniósł odpowiednio dla GeoEye-1 0,5 m i 1 m dla Ikonosa-2. Analiza dokładności została przeprowadzona na podstawie porównania odległości między punktami kontrolnymi, pomierzonymi na ortoobrazach i niebiorącymi udziału w orientacji, a odległościami obliczonymi ze współrzędnych pomierzonych za pomocą techniki GPS. Opracowanie to dotyczy wyżej wymienionych zagadnień. Całość została zakończona podsumowaniem oraz wnioskami wynikłymi w trakcie badań.
EN
The major purpose of this paper is to analyse stereopair orientation and bias compensation in rational polynomial coefficients. Moreover, the accuracy of digital terrain models and orthoimages generated from high-resolution satellite images acquired by GeoEye-1 and Ikonos-2 was evaluated. Bias, so the correction caused by increasing the accuracy of the RPC (Rational Polynomial Coefficient) correction, had been mentioned in a number of English articles by C. S. Fraser and H. B . H anley. They discuss the problem of orientation with regards to high resolution satellite imagery and the influence of bias on the results of this orientation. In Poland, there are not many publications concerning this topic, which is why our research team had decided to conduct the necessary research and analyses. GeoEye-1, launched in September 2008, commenced full commercial operations in February, 2009. As one of the first satellites it develops panchromatic images in a half-meter resolution. That is why the subject of this research are two panchromatic stereoscenes - one acquired by GeoEye-1, and second by Ikonos-2, launched in 1999. Both of them are representative satellites acquiring high-resolution image data. They have similar technique parameters, orbit characteristics, get images in panchromatic and multispectral modes and develop panchromatic scenes in less than 1-meter resolution. Used stereoscenes show the city of Hobart (Australia) and its neigbourhood. This area has variabled topography and includes the bay, strongly urban terrain and mountains covered with forest. The heights reach around from 0 to 1300 meters. This height variety can has significant impact on final photogrammetric products, what also was studied. In the project we used the part of the test field measured in 2004 by GPS, consisting of 19 control points which were used for orientation. The issue of this paper will be comparison of orientation effects carried on the different number of control points without changes in check point configuration. Depending on the analysis, the accurate number of control points to orientation of each stereoscenes was chosen. The next problem was bias compensation in RPC (Rational Polynomial Coefficients). An analysis of the relation had been conducted during scene orientation. Moreover, the correction equations of bias compensation before and after orientation depending on original RPC will be described. The important problem will be indication of relation between RMS error of orientation and standard deviation of line and sample in bias correction. After indication of the number of control points accurate to orientation and the most profitable parameters of line and sample, we generated digital terrain models. We used ABM correlation method. Output cell size for both of stereopairs was equal to 10 meters. Generated digital terrain models were studied in the aspect of point height accuracy by the comparison of heights measured by GPS with elevations measured on explored terrain models. The next stage was generation of orthoimages from single scenes of steropairs and analysis of their accuracy. The output cell size of generated photogrammetric products was equal to 0.5 and 1 meter for GeoEye-1 and Ikonos-2. Analysis of accuracy was provided in dependence on comparison of distances between check points not used in bundle adjustment and measured on generated orthoimages and distances computed from coordinates measured by GPS. The paper concerns the above problems and it is ended by summary and proposals coming from the research.
PL
Formy specjacyjne chromu można rozdzielać i oznaczać na wiele sposobów. Wśród metod rozdzielania najpowszechniej stosowana jest wysoko sprawna chromatografia cieczowa HPLC, ze względu na dostępność różnorodnych mechanizmów rozdzielania oraz faz ruchomych, pozwalających na zachowanie oznaczanej formy w stanach niezmienionych.
PL
Celem niniejszej pracy jest wykorzystanie mechanizmów zdalnego wywołania procedur do integracji wielu platform komputerowych do rozwiązania złożonych algorytmów obliczeniowych. W tym celu wykorzystano heterogeniczną sieć komputerową, składającą się z komputerów o różnej architekturze i pracujących pod kontrolą różnych systemów operacyjnych.
EN
The aim of this work is to use remote procedure call mechanisms to integrate multiple computer platforms in order to solve complicated computation algorithms. A heterogeneous computer network consisting of computers with different architectures and different operating systems.
PL
Praca miała na celu kompleksowe przebadane stereopary Ikonos dla celów automatycznej generacji modeli wysokościowych. Wykorzystano stereoparę przedstawiającą miasto Kraków i okolice; pracowano na oprogramowaniu Leica Photogrammetry Suit. Panchromatyczna stereopara o rozmiarze 11×22 kilometry posiadała terenowy wymiar piksela 0.80 m. Do orientacji stereopary wykorzystano dostarczone przez dystrybutora współczynniki RPC oraz naturalne fotopunkty pomierzone w technologii GPS. Analiza korekcji współczynników RPC wielomianami stopnia pierwszego, drugiego i trzeciego wykazała, że dla osiągnięcia dokładności subpikselowych wystarczający jest wielomian pierwszego stopnia. Osiągnięto następujące dokładność orientacji na 15 fotopunktach: Mx = 0.6 m; My = 0.4 m; Mz = 0.6 m; natomiast na 14 punktach kontrolnych: Mx = 0.6 m; My = 0.4 m; Mz = 0.8 m. Wykazano, że stosowanie większej ilości fotopunktów niż 9 nie prowadzi do znaczącej poprawy wyników orientacji a wykorzystanie wielomianów korygujących wyższych stopni może prowadzić do zniekształceń. W celu stworzenia NMPT wykonano automatyczną korelację (matching) w siatce 10 m. Analizę dokładności przeprowadzono na 46 punktach GPS i otrzymano średni błąd kwadratowy wysokości Mz = 1.6 m. Na potrzeby wygenerowania NMT przeprowadzono korelację w siatce 50 m, która pozwoliła na stworzenie NMT o dokładności Mz = 1.7 m. Na podstawie NMT przeprowadzono ortorektyfikację jednego z obrazów stereopary i stworzono ortofotomapę o pikselu 0.80 m. Dokładność sprawdzono na 24 fotopunktach GPS i otrzymano błędy: Mx = 0.93 m; My = 0.99 m. Eksperyment został przeprowadzony w Instytucie Fotogrametrii i Teledetekcji Politechniki Wiedeńskiej oraz w Instytucie Fotogrametrii i Kartografii Politechniki Warszawskiej.
EN
The main goal of the study was to investigate the potential of height model generation from very high resolution satellite images in Leica Photogrammetry Suite. The work was conducted at the Institute of Photogrammetry and Remote Sensing of the Vienna University of Technology and at the Institute of Photogrammetry and Cartography of the Warsaw University of Technology. The experiment was based on an Ikonos panchromatic stereo image with a resolution of 0.80 m and the size of 11×22 km. Orientation was done with RPC coefficients delivered by the distributor and photopoints measured in GPS technology. An analysis of RPC’s systematic errors correction using first, second and third order polynomials showed that for subpixel quality, a first order polynomial is sufficient. The achieved orientation accuracy was: on 15 control points – RMSx = 0.6 m; RMSy = 0.4 m; RMSz = 0.6 m, on 14 check points – RMSx = 0.6 m; RMSy = 0.4 m; RMSz = 0.8 m. It was shown that during work on the Polish normal heights system, if a polynomial of at least 1 order is not used, the results could be slightly degraded compared to work on an ellipsoid height system. Using more than 9 control points brings only slightly improvement to the stereo image’s orientation accuracy. RPC correction with polynomials of higher orders than the first is not advised, especially if a dense grid of control points is not assured. In order to generate DSM, matching was done which resulted in over 900 000 points. Accuracy analyses was done on 46 GPS points and gave the result of RMSz = 1.6 m. Points were placed mainly on roads, so this kind of analysis is reliable only for ground objects. For DTM generation, matching was done on a 50 m grid and manual filtration in LPS was conducted, which resulted in an accuracy of 1.7 m. The generated DTM and one of the images was used in orthorectification. Accuracy assessment of the generated ortho was done on 24 GPS points and gave the following results: RMSx = 0.93 m; RMSy = 0.99 m. In the experiment, the use of SCOP++ software for matched points filtration was investigated.The study was based on a dense 3 m grid point cloud. Although designed for laser scanning data, a robust filtering algorithm gave good results, even in the highly urban areas of Cracow.
PL
Jedną z najbardziej popularnych technik stosowanych w analizie peptydów i białek jest chromatografia z odwróconym układem faz (ang. Reversed-Phase Chromatography, RPC). Termin "odwrócony układ faz" został wprowadzony przez Howarda i Martina dla określenia chromatografii hydrofobowej, w której używa się niepolarnej fazy stacjonarnej i polarnej fazy ruchomej.
PL
Niniejsza praca przedstawia nową metodę wykorzystania mechanizmów zdalnego wywołania procedur do obliczeń równoległych. Zaproponowane rozwiązanie wykorzystujące rozproszone obszary pamięci dzielonej pozwala na zwiększenie efektywności mechanizmów RPC. Do jej oceny przedstawimy przykład jej zastosowania do rozwijania problemu równoległego wyszukiwania wzorca w bazie danych obrazów cyfrowych.
EN
The paper presents a new method of using Remote Procedure Call mechanisms for parallel programming. The proposed method which uses shared distributed memory increase RPC efficiency. An example of how to use the proposed method is also presented. It also allows to evaluate its purposefulness.
PL
W pracy zweryfikowano własny kinetyczny model populacji kropel w ekstraktorze przez porównanie obliczonych i doświadczalnych rozkładów wielkości kropel w kolumnie rozpyłowej, wypełnionej i z wibrującymi półkami (RPC). Stwierdzono dobrą zgodność obliczonych i zmierzonych rozkładów oraz wielkości kropel.
EN
Experimental data obtained for three distinctive kinds of columns (spray, packed, and reciprocating plate columns - RPC) were used to verify a kinetic model of drop population in any type of extractor. A favourable correlation was found between the data predicted by the model and those actually obtained through experimental observation.
first rewind previous Strona / 1 next fast forward last
JavaScript jest wyłączony w Twojej przeglądarce internetowej. Włącz go, a następnie odśwież stronę, aby móc w pełni z niej korzystać.