Artykuł przedstawia projekt wykorzystania potencjalnych zasobów geotermalnych w mieście i gminie Buk. W pierwszych rozdziałach przedstawione są warunki geotermalne dla analizowanego regionu oraz potencjalne zbiorniki geotermalne umożliwiające efektywną eksploatacje wód termalnych. W mieście Buk są to zbiorniki jury dolnej, triasu dolnego oraz permu dolnego. Przedstawiona została głębokość technologia wykonania dwuotworowego systemu dubletu geotermalnego. W kolejnych rozdziałach przedstawione są technologie sprężarkowych pomp ciepła umożliwiające maksymalizację wykorzystania ciepła geotermalnego. Na zakończenie przedstawione są potencjalne moce cieplne uzyskane z odwiertu i potencjalny efekt ekologiczny.
EN
The paper presents the potential use of geothermal resources in the town and municipality of Buk. The first chapters present the geothermal conditions for the analyzed region and the potential geothermal reservoirs for the efficient exploitation of thermal water. In the town of Buk, these are the Lower Jurassic, Lower Triassic and Lower Permian reservoirs. The technology of a two-hole geothermal doublet system is presented. In the following chapters, compressor heat pump technologies for maximizing the use of geothermal heat are presented. Finally, the potential heat capacities obtained from the borehole and the potential environmental effect are presented.
Poprawa efektywności energetycznej i racjonalne wykorzystanie istniejących zasobów energii w obliczu rosnącego zapotrzebowania na energię to obszary, do których Polska przywiązuje dużą wagę. Walka ze zmianami klimatycznymi zaczyna się teraz, ponieważ we współczesnym społeczeństwie to budynki są głównymi konsumentami energii. Oszczędzanie energii poprzez wyłączanie światła, używanie energooszczędnych urządzeń i żarówek pozwala zaoszczędzić na rocznych kosztach energii i obniża emisję CO2, a dobra izolacja i nowoczesne okna to tylko niektóre z wielu sposobów na zmniejszenie emisji i wysokości rachunków za ogrzewanie lub/i chłodzenie. W artykule przedstawiono aspekty poprawy efektywności energetycznej budynku przychodni zdrowia w Mszanie Dolnej poprzez zastosowanie kompleksowej termomodernizacji przegród zewnętrznych. Można stwierdzić, że dzięki termomodernizacji przegród zewnętrznych, najbardziej wrażliwych i nieszczelnych w obiekcie, czyli ścian zewnętrznych pod i nad ziemią wraz z dachem wentylowanym, udało się zaoszczędzić 53% energii cieplnej w budynku, co bezpośrednio przekłada się na obniżenie kosztów eksploatacji budynku. Poprawa wskaźników efektywności energetycznej waha się od 37% do prawie 60%, a redukcja emisji CO2 poprzez zmniejszenie zapotrzebowania na energię zużywaną w budynku na poziomie blisko 50%.
EN
Improving energy efficiency and rational use of existing energy resources in the face of growing energy demand are areas to which Poland attaches great importance. The fight against climate change starts now because in modern society buildings are the main consumers of energy. Saving energy by turning off lights, using energy- saving devices and light bulbs saves on annual energy costs and lowers CO2 emissions, and good insulation and modern windows are just some of the many ways to reduce emissions and heating and/or cooling bills. The article presents aspects of improving the energy efficiency of the health clinic building in Mszana Dolna through the use of comprehensive thermal modernization of external partitions. It can be said that thanks to the thermal modernization of the most sensitive and leaky external partitions in the building, i.e. external walls above and below the ground with a ventilated roof, it was possible to save 53% of the building's thermal energy, which directly translates into lower building operating costs. The improvement of energy efficiency indicators ranges from 37% to almost 60%, and the reduction of C02 emissions by reducing the demand for energy used in the building at the level of nearly 50%.
Artykuł przedstawia projekt wykorzystania potencjalnych zasobów geotermalnych w mieście i gminie Buk. W pierwszych rozdziałach przedstawione są warunki geotermalne dla analizowanego regionu oraz potencjalne zbiorniki geotermalne umożliwiające efektywną eksploatacje wód termalnych. W mieście Buk są to zbiorniki jury dolnej, triasu dolnego oraz permu dolnego. Przedstawiona została głębokość i technologia wykonania dwuotworowego systemu dubletu geotermalnego. W kolejnych rozdziałach przedstawione są technologie sprężarkowych pomp ciepła umożliwiające maksymalizację wykorzystania ciepła geotermalnego. Na zakończenie przedstawione są potencjalne moce cieplne uzyskane z odwiertu i potencjalny efekt ekologiczny.
EN
The paper presents the potential use of geothermal resources in the town and municipality of Buk. The first chapters present the geothermal conditions for the analyzed region and the potential geothermal reservoirs for the efficient exploitation of thermal water. In the town of Buk, these are the Lower Jurassic, Lower Triassic and Lower Permian reservoirs. The technology of a two-hole geothermal doublet system is presented. In the following chapters, compressor heat pump technologies for maximizing the use of geothermal heat are presented. Finally, the potential heat capacities obtained from the borehole and the potential» environmental effect are presented.
Przedstawiona w niniejszym artykule analiza warunków geotermalnych miasta Rogoźno pozwala na wybór najlepszego wariantu dla wykorzystania wód termalnych. Lokalizacja miasta w rejonie o wysokiej potencjalnej temperaturze i wydajności odwiertu pozwala na produkcję energii elektrycznej z zasobów geotermalnych. Przedstawiona symulacja obiegu ORC daje informację o możliwej wielkości produkcji, pozwala na ocenę symulowanej sprawności obiegu ORC dla różnych temperatur wód geotermalnych w zakresie 70 – 140°C. Przedstawiona koncepcja sposobów wykorzystania energii cieplnej wód geotermalnych pozwala na maksymalizację mocy wykonanego odwiertu geotermalnego. Dzięki wykorzystaniu odwiertu geotermalnego dla produkcji energii elektrycznej i cieplnej w różnych zakresach temperatur wykorzystanie potencjału inwestycji jest maksymalne.
EN
The article examines the geothermal conditions in Rogozno city, enabling the identification of the optimal approach for utilizing thermal waters. Due to its favorable location in a high-temperature region with ample well capacity, an ORC plant can be employed to generate electricity from geothermal resources. Through the simulation of the ORC cycle, insights are obtained regarding potential production volumes and the simulated efficiency across geothermal water temperatures ranging from 70 to 140°C. Moreover, the proposed strategies for harnessing geothermal energy maximize the output of drilled wells by utilizing them for both electricity and heat production at varying temperature ranges. This approach ensures the optimal utilization of the investment.
5
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
Biopaliwa zaliczane są do grona odnawialnych źródeł energii. Produkcja biopaliw do celów wykorzystania w silnikach spalinowych może zapewnić ich rozwój technologiczny oraz mieć wpływ ekonomiczny na sektor OZE i przemysł rolniczy, jednak ich wykorzystanie nadal stanowi istotny problem w eksploatacji tych silników. W artykule zbadano interakcję wybranych biopaliw z uszczelkami. Badane biopaliwa wyprodukowano z surowców odpadowych przemysłu spożywczego - tłuszczów i olejów. W artykule przedstawiono wpływ biopaliw na uszczelki złączy kołnierzowych, podczas badań trwałościowych. Materiał uszczelek (PTFE) został przetestowany zgodnie z normami DIN 28090-3:2014-11 i DIN28091-2. W czasie 1000 godzin badań w temperaturze 353 K mierzono ubytek masy biopaliwa oraz zmianę wydłużenia (naprężenia rozciągającego) śrub kołnierzowych. Określono stopień wycieku paliwa. Po badaniach sprawdzono uszczelkę i nie stwierdzono rozwarstwień. Wartość emisji lotnych biopaliw oraz stopień wycieku paliwa po 1000 godzinach odpowiadały normom DIN. Stwierdzono, że badane materiały uszczelniające mogą mieć kontakt z mieszaniną benzyna - etanol oraz mieszaniną oleju napędowego i estrów metylowych i etylowych.
EN
The biofuels are concerned as one of the Renewable Sources of Energy. Production of biofuels for transportation purposes may provide additional technological development and economical impact on agricultural industry, but their usage is still a vital problem for vehicle exploitation. In this paper an interaction between chosen biofuels and gaskets was researched. Tested biofuels were produced using waste materials from food industry - fats and oils. Biofuels influence on pipes and especially gaskets and its materials during durability tests are shown in this paper. PTFE gasket materials were tested in accordance with DIN 28090-3: 2014-11 and DIN28091-2. During 1000 hours of tests at 353 K, the weight loss of the biofuel and the change in elongation (tensile stress) of the flange bolts were measured. Fuel leakage rate was determined. After tests the gasket was checked and no delamination was observed. The value of volatile biofuels emission and fuel leakage rate after 1000 hours met the DIN standards. It was concluded that researched gasket materials may be allowed for contact with gasoline - ethanol mixture and mixture of diesel and methyl and ethyl esters.
System czwartej generacji to efekt ciągłego rozwoju technologicznego w dziedzinie geotermii. Daje on możliwość wykorzystania bogactwa energii zgromadzonej w ziemi w sposób bardziej efektywny, ekonomiczny i ekologiczny.
The study presents the results of research related to the use of B75 biofuel to power compression ignition engines, which can be used in transport and agriculture. The biofuel is composed of fatty acid ethyl esters produced from rapeseed oil and waste vegetable fats in the process of ethanol transesterification and dehydrated bioethanol, with the addition of standard diesel oil (approx. 25%). The physical and chemical properties of the 3-component biofuel were determined in laboratory conditions, and its composition was enriched with additives, allowing the use of the biofuel in a wide range of ambient temperatures. The efficiency of engines fuelled with multi-component biofuel and the emission of toxic substances in exhaust gases were measured in laboratory conditions (engine dynamometer), as well as in the natural operation of vehicles used in transport (delivery vehicles). The results of the conducted research prove that the B75 biofuel can successfully replace the standard mineral diesel oil and may constitute the basis for the development of the B100 fuel composed of ethyl esters and ethanol.
PL
Opracowanie przedstawia efekty badań związanych z zastosowaniem biopaliwa B75 do zasilania silników o zapłonie samoczynnym, które może być wykorzystywane m.in. w transporcie i w rolnictwie. Biopaliwo skomponowane jest na bazie estrów etylowych wyższych kwasów tłuszczowych wytworzonych z oleju rzepakowego oraz odpadowych tłuszczów roślinnych w procesie transestryfikacji z bioetanolem i odwodnionego bioetanolu, z dodatkiem standardowego oleju napędowego (ok. 25%). Właściwości fizykochemiczne wytworzonego 3-komponentowego biopaliwa zostały określone w warunkach laboratoryjnych, a jego skład został wzbogacony dodatkami uszlachetniającymi, pozwalającymi stosować biopaliwo szerokim zakresie temperatury otoczenia. Efektywność pracy silników zasilanych wielokomponentowym biopaliwem oraz emisję substancji toksycznych w spalinach określono w warunkach laboratoryjnych (hamownia silnikowa), a także w naturalnej eksploatacji pojazdów wykorzystywanych w transporcie (pojazdy dostawcze). Wyniki przeprowadzonych badań dowodzą, że biopaliwo B75 może z powodzeniem zastąpić standardowy mineralny olej napędowy i stanowić może bazę do opracowania paliwa B100 złożonego z estrów etylowych i etanolu.
Publikacja przedstawia wariantową analizę kosztów wytwarzania ciepła dla istniejącej miejskiej ciepłowni w Oławie. W analizie wzięto pod uwagę koszty wytwarzania dla istniejącego źródła ciepła – kotła węglowego oraz poddano analizie alternatywne warianty wytwarzania ciepła: wariant z zastosowaniem kotła gazowego oraz dwa warianty wykorzystania niskotemperaturowych wód geotermalnych wspomaganych absorpcyjnymi lub sprężarkowymi pompami ciepła. W artykule opisano warunki istniejącej ciepłowni oraz warunki geotermalne w mieście Oława. Analizę ekonomiczną uzupełnia obliczenie uśrednionego kosztu wytwarzania energii (LCoH) wraz z analizą wariantu wykorzystania możliwości finansowania inwestycji z środków NFOŚiGW.
EN
The paper presents a variant analysis of heat production cost for the existing heating plant in Oława city. The analysis includes cost assessment for the existing heat source – coal boiler and alternatives for the modernization such as gas boiler and two variants of low-enthalpy geothermal water use supported by an absorption or compressor heat pump. The current heating plant was discussed as well as geothermal conditions in the Oława city. Economical analysis was completed with a calculation of the Levelized Cost of Heating (LCoH) with an analysis of the potential funding possibilities with NFOŚiGW funds.
Publikacja zawiera ocenę warunków geotermalnych, koncepcje zamiany obecnego zasilania ciepłowni przez spalanie węgla na geotermalny system sprężarkowych pomp ciepła. Oprócz analizy technicznej wykonalności została przeprowadzona analiza ekonomiczna. Przedstawiono warunki i potencjalne zbiorniki geotermalne: województwa, powiatu, gminy i miasta Oława. Zbiorniki: Triasu oraz Permu Dolnego zostały przeanalizowane pod względem ich głębokości, temperatury, przewodności hydraulicznej i potencjalnej wydajności ujęć. Na podstawie danych źródłowych (MZEC) uzyskano informacje o potencjalnej produkcji ciepła po przeprowadzonej modernizacji.
EN
The paper presents an assessment of the geothermal conditions and concept for replacing the current coal-fired heating plant with a geothermal compressor heat pump system. In addition to a technical feasibility analysis, an economic analysis was carried out. The conditions and potential geothermal reservoirs of the province, County and Oława municipality are presented. Reservoirs of the Triassic and Lower Permian were analyzed in terms of their depth, temperature, hydraulic conductivity and potential intake capacity. Based on historical data, potential heat production after modernization was obtained.
Artykuł przedstawia ocenę potencjału energetycznego, koncepcje geotermalnego systemu grzewczego, propozycję zamiany spalania na OZE, studium wykonalności i analizę ekonomiczną planowanej ciepłowni geotermalnej w mieście Nowy Tomyśl. W pracy zostały przedstawione warunki geologiczne Województwa Wielkopolskiego oraz określone potencjalne zbiorniki geologiczne województwa, powiatu i Gminy Nowy Tomyśl, pozwalające na eksploatacje wód termalnych. Zbiorniki: Kredy Dolnej, Jury Dolnej, Triasu Dolnego i Permu Dolnego zostały przeanalizowane pod względem ich głębokości, temperatury, przewodności hydraulicznej i potencjalnej wydajności ujęć. Została przeprowadzona analiza stanu obecnego i przedstawiono ekologiczny możliwy wariant modernizacji ciepłowni i sieci cieplnej w Nowym Tomyślu. W modernizacji przewidziano zastosowanie sprężarkowych pomp ciepła dużej mocy (SPCDM), pozwalających na maksymalne wykorzystanie ciepła geotermalnego w wysokotemperaturowej miejskiej sieci ciepłowniczej. Przeprowadzono analizę ekonomiczną z określeniem średniego kosztu ciepła (LCoH) i przepływów pieniężnych dla różnych wariantów finansowania i zasilania projektu geotermalnego miasta.
EN
The article presents the energy potential, concept for the geothermal heating system, proposition for replacement of combustion with renewable energy, feasibility study and economic analysis of the planned geothermal heating plant in the city of Nowy Tomyśl. This study presents geological conditions of the Greater Poland province and choice of the potential aquifers for the province, municipality and city of Nowy Tomyśl, that allow exploitation of thermal water. Aquifers of Lower: Cretaceous, Jurassic, Triassic and Permian were analyzed for their depth, temperature, hydraulic conductivity and potential yield of the borehole. Analysis of the current state was performed, with proposition of the ecological modernization option of the heating plant and network in Nowy Tomyśl. Modernization was proposed with use of high-power compressor heat pumps, that allow maximal exploitation of the geothermal heat in high temperature municipal heating network. Economical analysis was performed with calculation of Cash flow and levelized cost of heat for different financing and power supply options.
W artykule przedstawiono wyniki badań parametrów termodynamicznych w celu zwiększenia efektywności energetycznej sprężarkowej powietrznej pompy ciepła o mocy 14 kW. Publikacja zawiera: wprowadzenie, opis rynku pomp ciepła w Polsce oraz zakres wykonanych badań własnych oraz szczegółowo zawiera opis opracowanego modelu matematycznego z wykorzystaniem teorii i planowania eksperymentu.
EN
The article presents the results of research on thermodynamic parameters in order to increase the energy efficiency of a 14 kW air compressor heat pump. The publication includes: an introduction, a description of the heat pump market in Poland and the scope of own research, and includes a detailed description of the mathematical model developed using the theory and experiment planning.
One way to reduce the negative impact of internal combustion engines on the environment is to use advanced biofuels, e.g. Bioxdiesel which is a mixture of Fatty Acid Ethyl Esters (FAEE), bioethanol and standard diesel, with vast majority of the content with biological origin. The FAEE are promising content of the Diesel-Biodiesel-Ethanol blends. The FAEE can be obtained from both vegetable, eg. rapeseed oil and animal fats, as well as waste fats. The article presents research results on the efficiency of a turbocharged Diesel engine equipped with a Common Rail fuel injection system which was powered by Bioxdiesel fuel and for comparison purposes also fed with standard fuel. The effects study showed that even with a lower calorific value of Bioxdiesel fuel when compared to that for the standard diesel, the performance of the engine obtained during the test results was comparable to the standard fuel. Due to the presence of oxygen in the particles of the biofuel, and thus more efficient combustion processes, for a wide range of the minor engine load, the fuel consumption of Bioxdiesel and Diesel fuels was comparable to each other, while at higher engine load the fuel consumption of Bioxdiesel was lower than that for the other fuel.
Biodiesel fuel is covering more and more place in the market. The reason is a limited fossil fuels resources and the need to reduce emission of harmful substances by application of the fuel made of renewable resources. Currently in Poland and in Europe, the Fatty Acid Methyl Esters are used as biocomponent of the biodiesel fuel or it is used as pure biodiesel fuel. This paper presents the research on the biofuel, which contains mainly Fatty Acid Ethyl Esters, (the energetic value of FAEE is higher than FAME) and mineral Diesel fuel is a small addition. This paper presents research on the improvement of the compression ignition behaviour and combustion effectiveness of the second generation biofuel BIOXDIESEL, which contains up to 75% of biocomponents (FAEE with bioethanol) with addition of mineral Diesel fuel. Improvement of the auto-ignition properties is achieved through the multi-component composition of Bioxdiesel fuel and dosing of enriching additives. The quality of the fuel has been evaluated during engine testing and during laboratory measurement of fuel parameters. Whereas satisfactory results show that it is appropriate to supplement the composition of biofuels produced from waste vegetable and animal fats and alcohol with the refining additive.
JavaScript jest wyłączony w Twojej przeglądarce internetowej. Włącz go, a następnie odśwież stronę, aby móc w pełni z niej korzystać.