Wyniki wyszukiwania - BazTech

1

Use of a Raspberry PI single-board computer for image acquisition and transmission

Sieczkowski K., Sondej T.

Measurement Automation Monitoring

|

2017

|

Vol. 63, No. 5

180--182

EN

The article presents an analysis of the use of a single-board computer Raspberry PI for video acquisition and transmission. The article focuses on requirements necessary for the recorded image to be used for face analysis to identify facial expressions and microexpressions. The quality of the recorded video frames was verified for different resolutions and fps using PSNR (Peak Signal-to-Noise Ratio). Tests of CPU cores usage were also carried out for simultaneous recording and transmission of different types of video streams. The results show that the size of the effective image area depends on the resolution of recorded video stream. Increasing the frame rate for the given video resolution has a significant impact on the value of PSNR. And the resultant CPU usage, for the available resolutions and frame rates of the video recorded, in most cases does not exceed 15% of the total computing power of the CPU.

2

Projekt systemu zdalnego monitorowania zmian ciśnienia tętniczego krwi

Sieczkowski K., Sondej T., Dobrowolski A., Olszewski R.

Elektronika : konstrukcje, technologie, zastosowania

|

2017

|

Vol. 58, nr 1

17--21

PL

W artykule przedstawiono projekt systemu, przeznaczonego do zdalnego i ciągłego monitorowania zmian ciśnienia tętniczego krwi oraz wyniki badań testowych. Przedstawiony system złożony jest z osobistego urządzenia pomiarowego, punktu dostępowego do sieci Internet oraz ogólnodostępnego serwera danych. Istotnym elementem projektowanego systemu jest metoda ciągłego pomiaru zmian ciśnienia krwi, polegająca na określaniu czasu propagacji fali tętna. Czas ten wyznaczany jest pomiędzy charakterystycznym punktem sygnału elektrokardiograficznego (EKG) i sygnału fotopletyzmograficznego (PPG). W artykule przedstawiono wyniki badań testowych, dotyczących wyznaczania punktów charakterystycznych sygnału EKG i PPG metodą autokorelacyjną oraz wyniki pomiaru zmian czasu propagacji fali tętna.

EN

The article presents the design of the system for remote and continuous monitoring of changes in blood pressure and also results of the test. Presented system consists of a personal measuring device, the access point to the Internet and widely available data server. An important element of the designed system is a method for continuous measurement of changes in blood pressure, which based on determining the pulse wave transit time. This time is calculated between the specific point electrocardiogram (ECG) signal and the photoplethysmographic signal (PPG). The article presents the results of test on the determination of specific points of the ECG signal and the PPG based on autocorrelation method and the results of measuring changes in pulse wave transit time.

3

Real-time data acquisition based on common use interfaces at Matlab and embedded system

Sieczkowski K., Sondej T.

International Journal of Microelectronics and Computer Science

|

2016

|

Vol. 7, nr 3

100--108

EN

The article presents the tests of method for real-time data acquisition from embedded systems using Matlab software. Data transmission is performed using several common use interfaces: UART/USB, Ethernet, Bluetooth and WiFi. The article includes a description of a protocol, measuring station based on two types of embedded system, implementing the proposed protocol, as well as a description of the algorithm of test programs. Experimental studies were performed using a STM32F4 microcontroller and Raspberry PI-3 single-board computer. Executed tests related: (1) the average transmission time, (2) the effective throughput of a full cycle of data exchange, (3), the required working time of Matlab to handle the transmission, and (4) the stability of the program timer used for periodic data transmission calls. Experimental studies have shown that it is possible efficient data exchange between the embedded system and Matlab while maintaining the real-time requirements.

4

A method for testing the performance of a dual-core microcontroller with integrated program and data memory

Sieczkowski K., Sondej T.

Measurement Automation Monitoring

|

2015

|

Vol. 61, No. 7

320--322

EN

The paper presents a set of test procedures for performing an extended test of dual-core microcontroller performance. The procedures described enable the performance of the system to be determined with regard to memory organization, mutual influence of cores and ability to verify the impact of code optimization level. The experimental trials were performed using an LPC4357 microcontroller with onboard FLASH and SRAM memory. The results obtained showed a slight performance drop for the various microcontrollers operating simultaneously in typical conditions. However, with frequent references to a shared memory, the performance drop may reach as much as 80%.

5

The Structure and Properties of Mixed Welded Joints Made of X10NiCrAlTi32-21 and X6CrNiMoTi17-12-2 Steels

Sieczkowski K., Adamiec J., Sawicki G.

Archives of Metallurgy and Materials

|

2015

|

Vol. 60, iss. 3A

1801--1806

EN

This paper describes the welding technology applied for mixed joints of tubes made of austenitic steels in the X10NiCrAlTi32-21 and X6CrNiMoTi17-12-2 grades. One made a butt joint and a multi-run joint, with the inert gas welding method and a non-consumable electrode. The mechanical properties were tested in the following scope: static tensile test, bending test from the side of the face and from the side of the root, impact test of the joint and hardness measurements. The tests were supplemented by the assessment of the macrostructure and microstructure of the joint. The performed non-destructive and structural tests did not reveal any welding imperfections, and the mechanical test results confirmed high properties of the welded joint. On this basis, the joint was classified into the “B” quality level according to PN EN ISO 5817. The mechanical and structural test results constitute the basis for qualification of the welding technology according to PN EN ISO 15614.

PL

W pracy opisano technologię spawania złączy mieszanych rur ze stali austenicznych w gatunku X10NiCrAlTi32-21 oraz X6CrNiMoTi17-12-2. Wykonano połączenia doczołowe, wielościegowe, metodą spawania elektrodą nietopliwą w osłonie gazu obojętnego. Zakres badań właściwości mechanicznych obejmował: statyczną próbę rozciągania, próbę gięcia od strony lica i od strony grani oraz badania udarności złącza i pomiary twardości. Badania uzupełniono o ocenę makrostruktury i mikrostruktury połączenia. Przeprowadzone badania nieniszczące i badanie strukturalne nie ujawniły niezgodności spawalniczych, a uzyskane wyniki badań mechanicznych potwierdzają wysokie właściwości złącza spawanego. Na tej podstawie złącze zakwalifikowano do klasy jakości “B” według PN EN ISO 5817. Wyniki badań mechanicznych oraz badań strukturalnych stanowią podstawę do kwalifikowania technologii spawania wg PN-EN ISO 5817.