W czasie budowy nowego odcinka trasy drogowej wystąpiły uszkodzenia konstrukcji istniejących budynków mieszkalnych, położonych w sąsiedztwie głębokich wykopów zabezpieczanych oporowymi ścianami szczelinowymi. Opisano przebieg zdarzenia, uszkodzenia budynków, podjęte doraźne i docelowe działania zabezpieczające. Określono przyczyny awarii oraz przedstawiono sposób naprawy powstałych uszkodzeń.
EN
During the construction of new road route there were damages of residential buildings, located in the vicinity of deep excavations supported by diaphragm walls. The paper describes the course of event, damage to buildings, taken ad hoc and target hedging activities. They analyzed the cause of the failure and shows how to repair the resulting damage.
The aim of this paper was to find an answer to the question about the possibility of using steel welded mesh in building the retaining walls of gabion baskets. In light of the currently used gabion structure solutions, among which double-woven mesh is much more popular, the focus was put on the possibility of using welded mesh. A numerical analysis was conducted to examine the behavior of welded and woven mesh subjected to various loads and the results obtained for both types of mesh were directly compared. The maximal displacement in mesh nodes was admitted as the measurement of the system behavior (in the case of both undamaged and damaged mesh).
3
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
Wzmocnienie podłoża metodą wymiany dynamicznej polega na formowaniu kolumn, z kruszywa o różnej granulacji, ubijakami o dużych masach (10-20 t.), zrzucanych z wysokości do 25 m. Ze względu na specyfikację technologii dość istotne jest sprawdzanie na budowie założeń projektowych, np. średnicy i długości kolumn, ich zagęszczenia czy też sztywności. W tym celu przeprowadzane są między innymi: odkrywki kolumn, różnego rodzaju sondowania, czy też próbne obciążenia. Te ostatnie polegają na określeniu zależności „obciążenie-osiadanie”, najczęściej w zakresie nacisków pierwotnych i wtórnych, oraz na wyznaczeniu na ich podstawie modułów odkształcenia. W tym celu na głowicy kolumny układana jest sztywna płyta, a obciążenie realizowane jest siłownikami zapartymi o balast. Dobór średnicy płyty obciążającej zależy od średnicy i długości kolumn, oraz przewidywanych nacisków pod płytą. Często średnica płyty obciążającej jest mniejsza od średnicy kolumny. W artykule podjęto próbę określenia wpływu średnicy płyty stosowanej w próbnych obciążeniach na wyniki badań w postaci zależności „obciążenie-osiadanie” i uzyskanych na tej podstawie modułów odkształcenia. Obliczenia przeprowadzono metodą elementów skończonych, na wykalibrowanym na podstawie badania nośności kolumny, przestrzennym modelu numerycznym. Do obliczeń przyjęto modele: sprężysto-idealnie plastyczny i sprężysto-plastyczny ze wzmocnieniem izotropowym.
EN
The dynamic replacement method of soil strengthening consists in the constructing columns made of aggregate of various granularity. In order to form them, heavy pounders (weighing from 10 to 20 tonnes) are dropped from the height of 25 m. Considering the specificity of this technique, it is quite important to verify on site the assumptions of the project, such as diameter and length of columns, their compaction of stiffness. For that reason, a number of examinations are performed, including column excavations, various types of probing tests or trial loads. The latter consists in determining the “load-settlement” dependence – usually during initial and secondary loadings phase – and on their basis, indicating the value of deformation modulus. Therefore, a stiff plate is placed on the column head and the loading is realised using actuators leaning on the ballast. The diameter of the loading plate depends on diameter and length of column and on the predicted pressure under the plate. The diameter of the loading plate is often smaller than column’s diameter. This paper tries to determine the influence of the diameter of the plate used in test loads on the results of the research presented as “load-settlement” dependence and on the values of deformation modulus determined on their basis. The calculations were performed using FEM on a spatial numerical model calibrated on the basis of column’s bearing capacity tests. Two models were applied in calculations: elastic-ideally plastic and isotropic hardening elastoplastic.
The verification of limit states conditions of soil and foundation for an object constructed on bedrock requires a quantitative determination of the construction zone of influence. Due to time and cost factors, it is usually limited to boreholes performed in order to indicate the soil type and profile in terms of crackings. To determine the internal forces of the footing and construction for larger objects, especially statically indeterminate structures, it is crucial to know, e.g., the values of deformation and elasticity moduli. This paper presents the results of a number of tests performed to determine the stiffness of bedrock under silos in reconstruction. Trial loadings were performed and the settlement of soil under the adjacent construction was observed. Soil behaviour under the reconstructed silos was also monitored. Some of the results of the above-mentioned investigations served as the basis for back analyses carried out using the finite element method (FEM), in which stiffness parameters of rocky soil were determined. Based on the investigations and analyses, it was found out that the initial and secondary deformation moduli do not exceed the value of 230 MPa, which is at least a few times less than the elasticity moduli (455-1244 MPa). The analysis of internal forces in silos foundations, performed by the designer in order to indicate the stiffness of bedrock, resulted in the replacement of other 10 walls of the silos, without the necessity to modify the foundations.
Przedmiotem artykułu jest analiza porównawcza wyników obliczeń konsolidacji podłoża wzmocnionego wymianą dynamiczną, pod nasypem drogowym, otrzymanych na podstawie wybranych podejść analitycznych i numerycznych z wynikami pomiarów in situ prowadzonych w trakcie budowy. W podejściu analitycznym zastosowano jednowymiarową teorię Terzaghiego oraz trójwymiarową teorię Barrona. W obliczeniach numerycznych zamodelowano etapową budowę nasypu w układzie dwuwymiarowym. Przeprowadzona analiza wykazała, że pomierzone osiadania podłoża pod budowanym nasypem były zbliżone do ustalonych w wyniku obliczeń.
EN
The paper presents the comparative consolidation analysis of road embankment subsoil reinforced with the use of the dynamic replacement method. The results obtained from selected analytical and numerical methods applied in the dynamic replacement column dimensioning were compared with in situ measurements. The embankment founded on strengthened soil was monitored during its completion. The measurements were taken with accuracy and the results can be considered trustworthy. The analytical approach uses the one-dimensional theory of Terzaghi and three-dimensional theory of Barron. The numerical calculations using FEM reflected the particular stages of the embankment construction in a two-dimensional system. The measured settlements and the results of the calculations (dimensioning) by two different approaches were coherent. The paper can be considered as a case study report.
6
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
Na przykładzie działań przeprowadzonych w ramach przebudowy stadionu sportowego zaprezentowany został przykład wykorzystania MES do odwzorowania zależności obciążenie – osiadanie pali zagłębionych w utworach skalistych, poddanych próbnym obciążeniom statycznym. W ten sposób uzyskano skrajne wartości modułu Younga podłoża skalnego. Uzyskane wartości wykorzystano w pracach projektowych, m.in. do oszacowania osiadań, różnic osiadań i sił wewnętrznych w konstrukcji zadaszenia widowni stadionu sportowego, posadowionej na palach w utworach skalistych (zwietrzelinach piaszczystych i gliniastych).
EN
Activities performed during alteration of a sports stadium were used to create an example of using the FEM to map the load vs settlement relationship of piles inserted into rock formations and subjected to static test loads. This allowed to determine the extreme values of the rock formation Young’s modulus. These values were in turn used to i.a. evaluate the settlement, settlement differences and internal forces in the stadium’s roof structure which rests on piles inserted into rock formations (clay and sand eluvia).
7
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
Próba uchwycenia wpływu formowania pojedynczej kolumny kamiennej na prekonsolidację otoczenia gruntowego. Zmiany współczynnika prekonsolidacji OCR i parcia spoczynkowego K0 w funkcji czasu i odległości od punktu wzmocnienia na podstawie wyników przeprowadzonych sondowań statycznych i dylatometrycznych.
EN
The influence of the single stone column on the preconsolidation of adjacent soil. The changes of the preconsolidation coefficient OCR and of the at rest pressure, varying in time and depending on the distance from the point of strengthening on the basis of results obtained from CPU and dilatometric tests.
W przypadku przyczółków mostowych i dochodzących do nich nasypów, posadowionych w różny sposób na gruntach o małej sztywności, może dojść do nierównomierności ich osiadań. Stosowane na dojazdach płyty przejściowe mogą złagodzić ich występowanie tylko częściowo. Przedstawiono wyniki analizy numerycznej w postaci deformacji stref przejściowych, występujących na styku przyczółek-nasyp drogowy, posadowionych na gruntach o małej sztywności i różnej wodoprzepuszczalności.
EN
When bridge abutments and adjacent road embankments are founded on different types of soft subsoils it can arrive to different settlements. Transition slabs used as the approach ramps may reduce these effects but only partially. The results of numerical analysis presented in form of the deformation of transition zones in point of contact of abutment and road embankment were presented. Both structures were founded on different types of soft subsoils characterized by different water permeability.
The paper presents a comparative analysis of the consolidation of soil under a road embankment reinforced with stone columns. The results were obtained from the most common analytical and numerical methods applied in driven column dimensioning. The analytical approach exploits Terzaghi’s one-dimensional theory and Barronʼs three-dimensional theory. The numerical calculations reflected the particular stages of the embankment construction in various two- and three-dimensional systems. The geotechnical parameters that were crucial for the research were determined on the basis of geoengineering documentation, laboratory and field studies. The paper begins with a short introduction presenting the dynamic replacement method.
PL
Przedmiotem artykułu jest analiza porównawcza wyników obliczeń konsolidacji podłoża wzmocnionego wbijanymi kolumnami kamiennymi, pod nasypem drogowym, otrzymanych na podstawie najczęściej stosowanych, przy wymiarowaniu kolumn wbijanych, podejść analitycznych i numerycznych. W podejściu analitycznym zastosowano jednowymiarową teorię Terzaghiego oraz trójwymiarową teorię Barrona. W obliczeniach numerycznych zamodelowano etapową budowę nasypu w różnych układach płaskich i przestrzennych. Parametry geotechniczne, niezbędne do obliczeń, ustalone zostały na podstawie dokumentacji geologiczno-inżynierskiej, badań laboratoryjnych i polowych. Całość rozważań poprzedzona została krótką informacją na temat wymiany dynamicznej.
11
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
W artykule przedstawiono wyniki badań sztywności podłoża skalnego pod przebudowywanymi silosami na cement. Wspomniana przebudowa polegała na wymianie płaszczy silosów przy pozostawieniu istniejących fundamentów żelbetowych.
EN
The paper presents results of in situ tests of bedrock stiffness determination under rebuilded cement silos. That reconstruction included the concrete housing replacement on the existing foundations.
12
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
Próbne obciążenia jako jedno z podstawowych badań odbiorczych podłoża wzmocnionego wbijanymi kolumnami kamiennymi. Stanowisko do próbnych obciążeń. Badanie nośności kolumny wbijanej, wyniki tego badania i ich analiza.
EN
Trial load plate test of the driven stone columns as the primary field ground improvement quality control test. The trial load test stand. Description of single column bearing capacity test, its results and analysis.
13
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
Zanim przystąpiono do budowy obiektu biurowego na terenie byłego zakładu przemysłowego w Gliwicach, należało przeprowadzić badania mające na celu określenie warunków gruntowo-wodnych. Ich wyniki wskazały na możliwość zastosowania jednej z metod wzmocnienia słabego podłoża – ciężkiego ubijania.
14
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
Na początku artykułu scharakteryzowano kolumny kamienne formowane metodą wymiany dynamicznej. Następnie opisano warunki gruntowe na poletkach badawczych, metodykę wykonanych badań i proces formowania kolumny kamiennej. W artykule podano wysokości zrzutu ubijaka, jego zagłębienia po każdym zrzucie oraz objętości wprowadzanego kruszywa. Pokazano kształty kolumn określone na podstawie odkrywki. Kształty w obu przypadkach pozwoliły oszacować objętość kruszywa w kolumnach. Wartości te odniesione do objętości wtłoczonego kruszywa stanowią podstawę do analizy porównawczej wykonanej w ostatniej części artykułu. W analizie tej uwzględniono, pomierzone podczas testów, wyniesienie gruntu w promieniu do 6m od osi kolumny kamiennej. Całość wieńczą spostrzeżenia autorów na analizowany temat.
EN
The paper characterizes stone columns formed with the use of dynamic replacement method. In the following part, it describes soil conditions on test sites, research methodology and the stone column formation process. The paper contains the information about the drop height of the rammer, the depth on which it drops after every impact and the volume of the introduced aggregate material. Columns shapes determined on the basis of excavation were presented. In both cases, the shapes allowed to estimate the volume of the aggregate in columns. These values, in relation to the volume of the introduced aggregate, are the basis of the comparative analysis presented in the last part of the paper. The analysis takes into account ground heave measured during the tests in the radius of 6 metres from the column axis. Finally, the paper presents the authors' observations on the analyzed subject.
15
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
Wyniki badań polowych kształtu wbijanej kolumny kamiennej. Badania przy użyciu metody elektrooporowej oraz klasycznych przekopów za pomocą koparki. Wyniki w postaci map oporności elektrycznej oraz zdjęć i pomiarów w wykopie.
EN
The results of field tests of a rammed stone column shape. The research with the use of electrical resistivity tomography and a traditional excavation performed using an excavator. The results in the form of electrical resistivity maps, photos and measurements of the pit.
W artykule przedstawiono wyniki badań laboratoryjnych gruntu niespoistego ulepszonego (stabilizowanego) cementem oraz wyniki analiz numerycznych oceny wpływu stabilizacji na stateczność nasypu drogowego w określonych warunkach gruntowych.
EN
The paper presents the laboratory test results of granular soil stabilized with cement and numerical analysis results of influence of cement stabilization on road embankment stability in specified ground conditions.
W pracy przedstawiono wyniki badań polowych dotyczących wpływu formowania wbijanej kolumny kamiennej na jej otoczenie gruntowe. Wpływ ten wyrażony został zmianą efektywnego kąta tarcia wewnętrznego i spójności określonych w sondowaniu statycznym CPTU w trakcie, jak i po uformowaniu kolumny kamiennej.
EN
This paper presents the results of field tests performed to examine the influence of the rammed stone column formation process on the surrounding soil. The influence is expressed by cohesion and internal friction angle changes. These parameters were determined in cone penetration test (CPTU) during and after the stone column formation process performed with the use of dynamic replacement method.
19
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
This paper discusses the results of field tests which focused on deformation phenomena occurring in the surrounding of rammed stone column. The basic device used to perform the tests were inclinometers installed at different distances from the formed stone column. Not only the data obtained during inclinometer measurements were collected, but also additional data from ground uplift investigations, column excavation and the authors' observations. Each part of the paper presents firstly some general information on the subject in question and then the details concerning test field investigations.
PL
W artykule omówiono wyniki badań polowych skupiających się na poznaniu zjawisk deformacyjnych zachodzących w otoczeniu wbijanej kolumny kamiennej. Zasadniczymi narzędziami służącymi do wykonania testów były inklinometry zainstalowane w różnej odległości od formowanej kolumny kamiennej. Uzyskane za ich pośrednictwem wyniki uzupełnione zostały informacjami z badań wypiętrzeń gruntu, odkrywki kolumny oraz obserwacjami autorów. W poszczególnych częściach artykułu podano najpierw informacje ogólne, a następnie dane szczegółowe, odnoszące się do poletka badawczego.
20
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
W artykule przedstawiono wyniki oceny twardości i pracy łamania spoin po obróbce cieplnej złączy spawanych żarowytrzymałej stali niskostopowej T24 (7CrMo-VTiB10-10). Wykazano, że otrzymanie jednocześnie wymaganych właściwości plastycznych i twardości jest możliwe jedynie po wyżarzaniu w temperaturze co najmniej 700 stopni C. Podjęto również próbę wyjaśnienia przyczyn występowania niezadowalającej twardości złączy i udarności spoin po obróbce cieplnej w stosunkowo niskiej temperaturze wyżarzania.
EN
The paper presents the results of hardness test and nominal energy of impact test of welds after heat treatment of low alloy T24 (7CrMoVTiB10-10) steel. It is obtained that the required plasticity properties and hardness is possible only after annealing at a temperature of at least 700°C. It is made an effort to clarify the causes of unsatisfactory weld hardness and weld notch toughness after heat treatment at relatively low annealing temperature.
JavaScript jest wyłączony w Twojej przeglądarce internetowej. Włącz go, a następnie odśwież stronę, aby móc w pełni z niej korzystać.