Preferencje help
Widoczny [Schowaj] Abstrakt
Liczba wyników

Znaleziono wyników: 25

Liczba wyników na stronie
first rewind previous Strona / 2 next fast forward last
Wyniki wyszukiwania
help Sortuj według:

help Ogranicz wyniki do:
first rewind previous Strona / 2 next fast forward last
EN
The article presents the analysis of the dead time measurement using two sources for a non-paralyzable detector. It determined the optimum division of count rate measurement time between both source measurement and a single source one. Results of the work can be used to optimize dead time measurement for systems which count photons or particles.
PL
W artykule zaprezentowano analizę pomiaru czasu martwego detektora nieparaliżowalnego metodą dwóch źródeł. Wyznaczono optymalny podział czasu pomiaru częstości zliczeń dla pomiaru jednym i dwoma źródłami. Wyniki pracy mogą być wykorzystane do optymalizacji systemów zliczających fotony lub cząstki.
EN
This paper presents a comparison of purely scattering method of the finite-difference time-domain with the analytical solution for the case of two-dimensional TM wave and the object in the form of a cylinder made either from an ideal conductor or a dielectric material. The total scattering cross-section of the electromagnetic wave is calculated without transition from the near field to the far field. A simple algorithm for calculating wave power distributed on the control surface is presented. The dependence of the relative error of the scattering efficiency factor in the function of the number of iterations is shown for various values of scattering object diameter to wavelength ratios. The influence of relative dielectric constant of cylinder material on scattering efficiency coefficient is examined.
PL
Artykuł przedstawia porównanie czysto rozproszeniowej metody różnic skończonych z rozwiązaniem analitycznym dla przypadku dwuwymiarowej fali TM i obiektu w postaci cylindra wykonanego z idealnego przewodnika lub dielektryka. Całkowity przekrój dla fali elektromagnetycznej obliczono bez przejścia z pola bliskiego na dalekie. Przedstawiono prosty algorytm obliczania rozkładu mocy fali na powierzchni kontrolnej. Zależność błędu względnego wydajności rozpraszania w funkcji liczby iteracji została przedstawiona dla różnych wartości stosunku średnicy obiektu rozpraszającego do długości fali. Zbadano wpływ względnej przenikalności dielektrycznej materiału cylindra na współczynnik wydajności rozpraszania.
3
Content available Needle detector of X-ray and gamma radiation
EN
The article presents the developed structure of the novel needle proportional gas detector (NPC – Needle Proportional Counter) used for the detection of X-rays and gamma rays. The advantage of the detector is its simple mechanical construction and the possibility of detection of incident radiation in a direction parallel to the needle. The measured energy spectrum of the isotope Fe-55 by means of the developed detector is presented.
PL
Artykuł przedstawia opracowaną konstrukcję nowego typu gazowego detektora igłowego, służącego do detekcji promieniowania X i gamma. Zaletą detektora jest jego prosta konstrukcja mechaniczna i możliwość detekcji promieniowania w kierunku równoległym do igły. Zmierzono widmo energetyczne izotopu Fe-55 opracowanym detektorem.
EN
Gain prediction theory of single foil Gas Electron Multiplier detector was developed. Gas electron multiplier (GEM) detector with single foil was developed. Soft X-ray spectra with an energy of 5.9 keV emitted by the isotope Fe-55 were measured. On this basis, the dependence of gain and energy resolution from the detector voltage was determined. The simple theory of gain dependence on various detector parameters was developed. Preliminary results of the study confirmed the potential usefulness of the GEM detector as a substitute for the multiwire proportional chamber.
PL
Opracowano teorię wzmocnienia jednofoliowego detektora z gazowym powielaniem elektronów. Opracowano detektor z gazowym powielaniem elektronów z pojedynczą folią. Zmierzono widmo miękkiego promieniowania X, o energii 5,9 keV, emitowanego przez izotop Fe-55. Na tej podstawie wyznaczono zależność wzmocnienia i energetycznej zdolności rozdzielczej od napięcia zasilającego detektor. Opracowano prosta teorią zależności wzmocnienia od różnych parametrów detektora. Wstępne rezultaty badań potwierdzają potencjalną przydatność detektora GEM jako substytutu wielodrutowej komory proporcjonalnej.
PL
W artykule przedstawiono analizę układu wzmacniacza transimpedancyjnego współpracującego z fotodiodą i przełączanymi źródłami światła. Wyznaczono błąd sygnału spowodowanego pamiętaniem przez układ sygnału dla poprzedniego źródła światła oraz stosunek sygnału wyjściowego do niepewności pomiarowej. Wnioski z analizy mogą służyć do optymalizacji układów detekcji światła ze wzmacniaczami operacyjnymi i przełączanymi źródłami światła.
EN
In the article the analysis of the cross-talks in trans-impedance amplifier working with a photodiode and swicthed light sources was presented. The error caused by cross-talks and the signal to noise ratio were determined. The conclusions of this analysis may be used for optimization of light detection circuits with operational amplifiers and switched light sources.
PL
W artykule przedstawiono analizę optymalnego czasu zerowania pojemności w układzie integratora kluczowanego. Wyznaczono stosunek sygnału do szumu na wyjściu układu. Wnioski z analizy mogą służyć do optymalizacji układów detekcji światła z integratorami kluczowanymi.
EN
In the article the analysis of the optimal capacitance reset time in switched integrator was presented. The signal to noise ratio was determined. The conclusions of this analysis may be used for optimization of light detection circuits with switched integrators.
PL
W artykule przedstawiono analizę wpływu parametrów wzmacniacza operacyjnego na pracę układu integratora kluczowanego. Przeanalizowano wpływ pasma przenoszenia wzmacniacza, jego pojemności i rezystancji wejściowej, na stosunek sygnału do szumu na wyjściu układu. Wnioski z analizy mogą służyć do optymalizacji układów detekcji światła z integratorami kluczowanymi.
EN
In the article of the influence of operational amplifier parameters on work of switched integrator was presented. The influence of the bandwidth, input capacitance and resistance on signal to noise ratio was investigated. The conclusions of this analysis may be used for optimization of light detection circuits with switched integrators.
PL
W artykule przedstawiono analizę szumową układu integratora kluczowanego z nieidealnym kluczem. Przeanalizowano wpływ szumu termicznego rezystancji klucza w stanie otwartym na stosunek sygnału do szumu na wyjściu układu. Wnioski z analizy mogą służyć do optymalizacji układów detekcji światła z integratorami kluczowanymi.
EN
In the article noise analysis of switched integrator with non-ideal switch was presented. The influence of thermal noise of open switch resistance on signal to noise ratio was investigated. The conclusions of this analysis may be used for optimization of light detection circuits with switched integrators.
EN
The high sensitivity time correlated single photon counting system (with photomultiplier tube) for biomedical measurements was designed and tested. Photon time of flight through a parafine wax phantom was modeled by Monte Carlo simulation and next measured by the device. Mean time delay introduced by a phantom is in a good agreement with simulation results. The results presented in this paper demonstrate the feasibility of measuring the optical response with the device.
10
EN
A complete system for measurement control, signal acquisition and data processing for an OCT pachymeter is described. Moreover, dedicated data processing algorithm used for noise reduction is presented. A simple OCT scanner was built and some measurements were performed to examine the capabilities of the system.
PL
W pracy porównano dwa układy odbioru sygnału prądowego z fotodiody: pierwszy z integratorem o działaniu ciągłym (wzmacniaczem transimpedancyjnym) i drugi z integratorem kluczowanym. Układ z integratorem kluczowanym zapewnia lepszy stosunek sygnał-szum. Wnioski z analizy posłużyły do konstrukcji wielokanałowego systemu do badania ukrwienia tkanek metodą optyczną.
EN
In this work two circuits for photodiode current measurement were compared: the first with trans-impedance amplifier (current-to-voltage converter) and the second - switched integrator. The switched integrator has a better signal-to-noise ratio. The conclusions were used in designing multi-channel system for blood concentration changes in tissue by optical technique.
PL
Zaprezentowano wielokanałowy system do badania ukrwienia tkanek metodą optyczną. Urządzenie może pracować zarówno w trybie transmisyjnym, jak i odbiciowym. Przy jego wykorzystaniu możliwe jest obrazowanie ukrwienia podpowierzchniowych warstw tkanek miękkich. Przedstawiono wyniki badań na fantomach oraz wstępne wyniki pomiarów in vivo ukrwienia palców dłoni oraz tkanki miękkiej przedramienia. Po przeprowadzeniu wzorcowania urządzenie może posłużyć do wielopunktowych pomiarów utlenowania krwi.
EN
Designed multichannel device used for blood concentration changes in tissue was presented in the article. Elaborated system consists of red and infrared light sources, eight single channel photo-detector units and main control board. The exemplary results of measurement of blood concentration changes in forearm tissue were presented.
PL
Zaprezentowano system do pomiaru czasu przelotu fotonów przez tkankę. Opracowany system zawiera impulsowe źródło światła, fotodetektor i układ do pomiaru krótkich czasów. Przedstawiono wyniki pomiarów rozkładów czasu przelotu w fantomach.
EN
Designed time-resolved system, used for photon time of flight measurement was presented in the article. Elaborated system consists of pulse light source, high speed PMT and circuit for short time interval measurement. The results of photon time of flight distributions measured in phantoms were presented.
PL
Zaprezentowano jednokanałowy system do detekcji i zliczania pojedynczych fotonów. Opracowany system składa się z fotopowielacza, pracującego w trybie zliczania fotonów, układu wzmacniającego, dyskryminatora i licznika. Przeprowadzono testy urządzenia, które potwierdzają możliwość zastosowania go w technikach obrazowania optycznego w medycynie i biologii.
EN
Elaborated single photon counting system, used for biomedical purposes was presented in the article. Designed system consists of CW light source, high speed PMT working in single photon counting mode, fast amplifier, discriminator and counter. The results of photon amplitudę distribution measurement were presented.
EN
Optical tomograph with fixed geometry was designed and build. The tomograph was used for mesaurements of phantoms. Experimental data was used for reconstruction algorithms testing.
16
Content available remote Fixed geometry optical scanner for laboratory use
EN
A research stand of diffuse optical tomography consisting of a developed laboratory optical scanner with fixed geometry and a PC computer was constructed. The analysis of usefulness of particular groups of image sensors (photodiodes p-n, photodiodes p-i-n, photomultipliers, CCD matrices and CIS matrices) and light sources (for visible and near-infrared light) for diffuse optical tomography was carried out. Optimization of the reconstruction process was performed. A number of software tools for simulation of the light propagation in tissue was developed. The innovative method, combining advantages of nodal and Monte Carlo methods, was proposed.
PL
Przeprowadzono badania nad optymalnym doborem luminescencyjnych sensorów obrazu do systemów radiografii medycznej. Jako kryterium optymalizacji przyjęto uzyskanie maksymalnego stosunku sygnału do szumu w obrazie, scharakteryzowanego przez kwantową wydajność detekcji sensora (DQE). Sformułowano model fizyczny zjawisk zachodzących w luminescencyjnych sensorach obrazu. Opracowany model wykorzystano do obliczeń i symulacji parametrów sensorów (DQE i funkcji przenoszenia modulacji MTF) metodą Monte - Carlo oraz określenia ich optymalnych struktur.
EN
Investigation of the optimal selection of luminescent image sensors for medical radiographic systems. The main criterion of the optimization was obtaining the maximal signal - to - noise ratio in the image, characterized by the sensor detective quantum efficiency (DQE). The physical model of phenomena proceeding in luminescent image sensors was developed. The model was used to compute and simulate the sensor parameters (DQE and modulation transfer function MTF) by means of Monte - Carlo methods and to determine optimal structures.
EN
DQE (detective quantum efficiency) and MTF (modulation transfer function) of a few radiographic luminescent sensors were calculated according to the simple analytical model (originally developed by Swank and reformulated by the authors). Next, these parameters were determined using the specialized Monte Carlo simulation program and compared with analytical results. The discrepancies were discussed, and constructive conclusions for more sophisticated analytical models were formulated.
19
Content available remote Elektronika odczytu komór słomkowych w eksperymencie COMPASS
PL
W artykule przedstawiono kompleks problemów związanych z projektowaniem i budową komór słomkowych oraz współpracuiących z nimi elektronicznych układów odczytu i rejestracji danych. Przedstawiono rozwiązania stworzone na użytek eksperymentu COMPASS (CERN), w którym komory słomkowe pełnią rolę tzw. wielkopowierzchniowego detektora śladowego (Large Area Tracker), stanowiącego wraz z magnesem i detektorem Czerenkowa (RICH) pierwszy na drodze wiązki szerokokątny spektrometr cząstek. Główny nacisk położono na problemy zawiązane z uzyskaniem dużej odporności komory słomkowej na zakłócenia, niezbędnej dla uzyskania wysokiej pozycyjnej zdolności rozdzielczej.
EN
A set of problems related to design and construction of the straw chambers, their read-out electronics and data acquisition system is presented. Some solutions applied in the COMPASS experiment are shown. Straw chambers, together with a bending magnet and Cherenkov detector, are the main components of the Large Area Tracker in this experiment. Low noise and high EMI immunity of the system in terms of achieved spatial resolution is the main topic of the article.
PL
Opracowano metodykę i aparaturę do przesiewowych badań gęstości składowej mineralnej kości w diagnostyce osteoporozy. Skonstruowany skaner z głowicą scyntylacyjną może współpracować z dowolnym diagnostycznym aparatem rtg. Zoptymalizowano konstrukcję skanera i warunki pomiarów gęstości kości przedramienia, przyjmując jako główne kryterium minimalizację błędu losowego pomiaru przy ustalonej dawce promieniowania. Podano wyniki pomiarów parametrów skanera oraz przykładowe badania gęstości kości przedramienia.
EN
Methodology and equipment for osteoporosis screening were developed. A scanning system with a line, phosphor image detector for the diagnosis of osteoporosis was constructed. It can work with any diagnostic X-ray unit. The optimization of the scanning system with a scintillating head was carried out. The minimalization of the radiation dose with fixed precision was the main criterion for the optimization. The results of the scanning system parameter measurements and examples of bone density measurements are presented.
first rewind previous Strona / 2 next fast forward last
JavaScript jest wyłączony w Twojej przeglądarce internetowej. Włącz go, a następnie odśwież stronę, aby móc w pełni z niej korzystać.