The widespread use of Fibre-Reinforced Polymers (FRP) reinforced concrete (RC) structural members is hindered by their low fire resistant characteristics, limiting their use to cases, where fire resistance is not a priority. Presented and discussed are experimental results pertaining to the flexural members subjected to heating and simultaneous loading. Solely non-metallic FRP bars: (i) Basalt FRP (BFRP), (ii) Hybrid FRP (HFRP) with carbon and basalt fibres and (ii) nano-Hybrid FRP (nHFRP) with modified epoxy resin, were used as internal reinforcement for beams. The destruction of the beams was caused in different ways, beams reinforced with BFRP bars were destroyed by reinforcement failure while those reinforced with hybrid FRP bars were destroyed by concrete crushing. The BFRP reinforced beams obtained a maximum temperature, measured directly on the bars, of 917°C, compared to beams reinforced with hybrid FRP bars, where the temperature on the bars reached 400-550°C at failure. Moreover, the highest registered ductility was obtained for BFRP reinforced beams as well, where the maximum deflections reached approximately 16 cm.
PL
Degradacja nośności zbrojenia konstrukcji w postaci prętów FRP (ang. Fibre-Reinforced Polymers) może być spowodowane kilkoma czynnikami, do których należą: rodzaje włókien, osnowy (matrycy), ich objętościowy udział, sposób wytwarzania, jakość składników prętów. Jednakże głównym czynnikiem jest przede wszystkim wpływ temperatury w zbrojeniu FRP, występujący w trakcie oddziaływania warunków pożarowych. Zjawisko redukcji nośności konstrukcji i przyczepności zbrojenia do betonu pojawia się, gdy temperatura prętów FRP zbliża się do temperatury zeszklenia Tg osnowy (matrycy), której wartość zależy od rodzaju żywicy. Jednym z rozwiązań w tym zakresie jest zastosowanie większej otuliny lub zastosowanie dodatkowego systemu ochrony przeciwpożarowej. Jednak obecnie dostępne dane na temat zachowania elementów betonowych zbrojonych FRP w warunkach pożarowych, są ograniczone, szczególnie w odniesieniu do nośności belek po poddaniu ich oddziaływaniu wysokich temperatur. Dlatego odporność ogniowa elementów betonowych zbrojonych FRP jest jednym z podstawowych czynników, które utrudniają powszechne stosowanie tych materiałów jako alternatywy dla zbrojenia stalowego. W artykule opisano zachowanie się belek betonowych, zbrojonych prętami FRP wyprodukowanych na bazie włókien bazaltowych i węglowych, poddawanych testom odporności ogniowej. Badania belek narażonych na wysokie temperatury, przeprowadzono według scenariusz pożaru umownego zgodnie z krzywą standardową ISO-834 [13], [29]. Ponieważ głównym celem było zbadanie wpływu rodzaju zbrojenia FRP na odporność ogniową belek, zastosowano różne rodzaje prętów w strefie rozciągania (dolna część belek): (i) zbrojenie na bazie włókien bazaltowych BFRP (ang. Basalt FRP), (ii) hybrydowe zbrojenie HFRP (ang. Hybrid FRP) z włóknami węglowymi i bazaltowymi oraz (ii) nanohybrydowymi prętami nHFRP (ang. nano-Hybrid FRP) ze zmodyfikowaną żywicą epoksydową. Ponadto, badane elementy charakteryzowały się zmiennym stopniem zbrojenia, w celu określenia wpływu średnicy i liczby prętów na nośność belek podczas i po oddziaływaniu wysokich temperatur.
The paper describes the recent developments of Hybrid Fibre-Reinforced Polymer (HFRP) and nano-Hybrid Fibre-Reinforced Polymer (nHFRP) bars manufactured using the pultrusion process. Hybridization of less expensive basalt fibres with carbon fibres leads to more sustainable alternative to Basalt-FRP (BFRP) bars and more economically-efficient alternative to Carbon-FRP (CFRP) bars. At the same time the properties of the proposed bars can be modified by changing the bars configuration. The New-Developed HFRP bars were subjected to tensile axial loading to investigate its structural behaviour. The effect of hybridization on tensile properties of HFRP bars was verified experimentally by comparing the results of tensile test of HFRP bars with non-hybrid BFRP bars. It is possible to improve and predict the final mechanical characteristics of HFRP bars through mechanical hybridization of constituents and their volume fractions before it will be produced. The analytical/numerical considerations and experimental testing showed the same tendency in obtained results. In pre-manufacturing phase it was set that for the final mechanical properties, the influence of bar configuration is less important than the influence of different volume fractions of fibres. In addition, it was assumed that the preferable location of carbon fibres will be in the core region due to technological problems. It is worth to mention that the difference in obtained strength characteristics between analytical and numerical considerations was very small, however the obtained results were much higher than results obtained experimentally. Authors suggested that lower results obtained experimentally can be explained by imperfect interphase development and therefore attempted to improve the chemical cohesion between constituents by adding nanosilica particles to matrix consistency.
PL
W artykule zostały przedstawione najnowsze postępy w zakresie zachowania mechanicznego hybrydowych prętów FRP (HFRP) oraz nano-hybrydowych (nHFRP) produkowanych w procesie pultruzji. Hybrydyzacja włókien bazaltowych z włóknami węglowymi prowadzi do bardziej zrównoważonej alternatywy dla prętów na bazie włókien bazaltowych (BFRP) i bardziej ekonomicznej alternatywy dla prętów FRP na bazie włókien węglowych (CFRP). Jednocześnie właściwości proponowanych prętów można modyfikować zmieniając ich konfigurację. Nowo opracowane pręty HFRP poddano obciążeniu osiowemu przy rozciąganiu, aby zbadać jego zachowanie strukturalne. Wpływ hybrydyzacji na właściwości mechaniczne prętów HFRP zweryfikowano doświadczalnie, porównując wyniki próby rozciągania prętów HFRP z niehybrydowymi prętami BFRP. Możliwa jest poprawa i przewidywanie końcowych właściwości mechanicznych prętów HFRP poprzez mechaniczną hybrydyzację składników i ich udziałów objętościowych przed ich wyprodukowaniem. Analityczne i numeryczne rozważania oraz badania eksperymentalne wykazały tę samą tendencję w uzyskanych wynikach. W fazie przedprodukcyjnej ustalono, że dla końcowych właściwości mechanicznych wpływ konfiguracji pręta jest mniej ważny niż wpływ różnych udziałów objętościowych włókien. Ponadto założono, że preferowane położenie włókien węglowych będzie zaproponowane bliżej rdzenia prętów ze względu na problemy technologiczne. Warto wspomnieć, że różnica w uzyskanych charakterystykach wytrzymałościowych między rozważaniami analitycznymi i numerycznymi była bardzo mała, jednak uzyskane wyniki były znacznie wyższe niż wyniki uzyskane eksperymentalnie. Autorzy sugerują, że niższe wyniki uzyskane eksperymentalnie można wyjaśnić niedoskonałym rozwojem interfazy i dlatego próbowano poprawić spójność chemiczną między składnikami przez dodanie cząstek nanokrzemionki do konsystencji matrycy.
W pracy przedstawiono sposób realizacji projektu instalacji chemicznej do wydzielenia acetonu z wody w procesie ekstrakcji z użyciem octanu etylu jako rozpuszczalnika. Projekt wykonano w duchu metodyki projektowania BIM (Building Information Modeling), polegającej na stworzeniu dokumentacji 2D (schematy technologiczne, rysunki 2D, rysunki izometryczne rurociągów), modelu 3D instalacji oraz zarządzaniu danymi procesowymi 1D (dane obliczeniowe). Wykonanie projektu miało na celu sprawdzenie efektywności BIM w projektowaniu wspomaganym komputerowo, które obecnie jest głównym etapem w procesie inwestycyjnym.
EN
The article presents the method of carrying out a chemical installation project for the separation of acetone from water in the extraction process using ethyl acetate as a solvent. The project was conducted out in the spirit of the BIM (Building Information Modeling) design methodology, based on the creation of 2D documentation (technological diagrams, 2D drawings, isometric drawings of pipelines), 3D installation model and 1D process data management (calculation data). The implementation of the project was aimed at checking the effectiveness of BIM in computer-aided design, which is currently the main stage in the investment process.
The paper focuses on the issue of non-financial indicators in construction companies in Slovakia through the Balanced Scorecard concept as a tool of strategic management. The main aim of the paper is to find out the current state of using the method of Balanced Scorecard in construction companies in Slovakia. Two hypotheses were established in the study which was verified using the method of proportion of the given phenomenon in the population and the method of chi-square test for independence. Another part of our research was dedicated to the barriers that prevent the use of the BSC method wchich we have also subjected to the statistical research in our paper using the standard deviations and other statitical methods. The research has shown that the Balanced Scorecard method is not use even by 15% of construction companies in Slovakia. The partial objective was to find out the existence of statistically significant relationship between the use of non-finnacial indicators in the management and the use of BSC concept, since the BSC method assigns the same importance to both financial as well as non-financial indicators. The paper offers an overview about the current state of BSC in the construction industry and seeks to present the concept as a modern business management tool that gives equal importance to both financial and non-financial indicators.
PL
Artykuł koncentruje się na problemie wskaźników niefinansowych w spółkach budowlanych na Słowacji za pomocą koncepcji Balanced Scorecard jako narzędzia zarządzania strategicznego. Głównym celem artykułu jest poznanie obecnego stanu wykorzystania metody Balanced Scorecard w firmach budowlanych na Słowacji. W badaniu ustalono dwie hipotezy, które zweryfikowano za pomocą metody proporcji danego zjawiska w populacji i testu zgodności chi-kwadrat pod kątem niezależności. Kolejna część naszych badań poświęcona była barierom, które uniemożliwiają zastosowanie metody BSC, którą również poddaliśmy badaniom statystycznym przy użyciu odchyleń standardowych i innych metod statystycznych. Badania wykazały, że metoda Balanced Scorecard nie jest wykorzystywana nawet przez 15% firm budowlanych na Słowacji. Celem pośrednim artykułu było ustalenie istnienia statystycznie istotnego związku między wykorzystaniem wskaźników pozafinansowych w zarządzaniu i stosowaniu koncepcji BSC, ponieważ metoda BSC przypisuje to samo znaczenie zarówno do wskaźników finansowych, jak i niefinansowych. Artykuł przedstawia przegląd aktualnego stanu BSC w branży budowlanej i stara się przedstawić tę koncepcję jako nowoczesne narzędzie do zarządzania przedsiębiorstwem, które nadaje równe znaczenie wskaźnikom finansowym i niefinansowym.
Niniejsza publikacja przedstawia analizę zmian drzewostanów dla obszaru warszawskiej dzielnicy Wilanów, opracowaną na podstawie danych fotogrametrycznych. Wykorzystując różne technologie fotogrametryczne: dopasowanie obrazów cyfrowych i archiwalne lotnicze skanowanie laserowe dokonano wieloczasowej analizy zmian, która pozwoliła na otrzymanie informacji o zasięgu i występowaniu drzew w dwóch badanych okresach. Nadrzędnym problemem postawionym w badaniu było uzyskanie odpowiedzi na pytanie, jak duże zmiany w zasięgu i wysokościach drzewostanów zaszły na przestrzeni lat 2012 - 2017 oraz gdzie nie występują drzewa w 2017 roku. Wytworzone numeryczne modele pokrycia terenu zostały wykorzystane do analizy zmian występowania drzewostanów dla obszaru całej dzielnicy, w tym do detekcji miejsc ubytku koron drzew. Przeprowadzona analiza zmian wykazała ubytek biomasy dla 18.2% pojedynczych drzew, w tym, zniknięcie 11.7% drzew oraz zmniejszenie wysokości (zapewne poprzez przycięcie) dla 6.5%.
EN
This publication presents the analysis of tree stands’ changes for the area of Wilanów district in Warsaw, based on photogrammetric data. Using different photogrammetric techniques, such as image matching techniques and archival airborne laser scanning, a multitemporal analysis of vegetation changes was carried out. It enabled receiving information on the range and occurrence of trees in two different periods of time. The overriding work problem was to answer the question of how noticeable changes in trees stands’ range and height occurred over 2012 - 2017. Generated digital elevation models were used for the analysis of tree stands’ changes in the Wilanów district and the detection of places with the crowns’ loss. The carried analysis of changes showed loss of biomass for 18.2% of single trees, including disappearance of 11.7% of trees and reduction in height (probably by trimming) for 6.5% of trees.
W artykule omówiono skoordynowaną organizację miejskiego ruchu kilku tramwajów poruszających się zgodnie z kryterium minimalnego zużycia energii. Wszystkie tramwaje wyposażone były w trójfazowe silniki indukcyjne. Uwzględniony został wpływ sygnalizacji świetlnej na skrzyżowaniu przy formułowaniu procedury jazdy energooszczędnej. Najpierw podano przykład takiej jazdy trzech tramwajów, gdy sygnalizacja świetlna zapewniła wszystkim pojazdom przejazd przy zielonym świetle, a więc bez żadnego oczekiwania. Zostały również przeanalizowane dwa przypadki, gdy sygnalizacja świetlna spowodowała krótki oraz długi postój tramwaju. Pokazano, że w przypadku długich nieplanowych postojów likwidowanie opóźnienia wymaga odpowiedniego zaplanowania dalszej jazdy z większą prędkością na kilku kolejnych odcinkach jazdy.
EN
The paper deals with the coordinated organization of city ride of some trams running in accordance to the criterion of the minimum energy use. All trams were driven by three-phase induction motors. The influence of light signalling on the crossing has been taken into account at elaboration of the procedurę of the energy-saving traffic. First the ride of three trams was described at green light for every vehicle and here no waiting was necessary. There were also analysed two variants of disturbances caused by the light signalling: additional short and long tram stop because of the red light. For greater time lags of the traffic, the ride delay must be liquidated during the quicker run between some successive stops; the ride algorithm ought to ensure the minimum energy use.
7
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
W artykule przedstawiono wyniki badań właściwości mechanicznych szalunkowych dźwigarów nośnych systemu H20. Celem badań było określenie jakości i powtarzalności wykonania dźwigarów z partii próbnej oraz ich przydatności do użycia w standardowych szalunkach systemowych. Artykuł zawiera wyniki badań wytrzymałości w odniesieniu do modelu użytkowego zdefiniowanego przez zamawiającego badania oraz do normowych wartości granicznych. Omówiono uzyskane wyniki i podano przykłady zaobserwowanych nieprawidłowości.
EN
The article presents the results of the mechanical properties of the H20 formwork system girders. The aim of the study was to evaluate the quality and repeatability of girders from a sample bath and their usefulness in standard formwork system. The article contains the results of strength tests in respect to usable model defined by the research customer and in relation to the code limits. Results are discussed and examples of observed anomalies are given.
The aim of this paper is to present the Erotetic Reasoning Corpus (ERC) which constitutes a data set for research on natural question processing. We describe the theoretical background, linguistic data and tags used for the annotation process. We also discuss the potential areas in which the ERC can be exploited.
Przedstawiono wyniki badań związanych z oceną hybrydowych prętów kompozytowych jako niemetalicznego zbrojenia wybranych elementów betonowych stosowanych w obiektach infrastrukturalnych. Stwierdzono, że zwiększenie sztywności prętów kompozytowych z włókien bazaltowych BFRP (Basalt Fiber Reinforced Polymer) można uzyskać przez zastąpienie części włókien bazaltowych włóknami węglowymi. Omówiono efekty podjętej produkcji tego rodzaju prętów.
EN
The results of research related to the evaluation of hybrid composite bars as non-metallic reinforcement of selected concrete members used in infrastructural facilities are presented. It has been found that increasing the stiffness of basalt fiber composite bars (BFRP) can be achieved by replacing some basalt fibers with carbon fibers. The results of the production of such bars are discussed.
Przedstawiono wyniki badań właściwości mechanicznych dźwigarów nośnych systemu H20. Określono momenty zginające i siły ścinające przy zniszczeniu dźwigarów i porównano z wartościami granicznymi według normy DIN 1052:2004-08. Omówiono wady badanych dźwigarów i oceniono, że nie kwalifikują się one do stosowania w praktyce.
EN
The results of investigations of mechanical properties of the H20 bearing girders are presented. Bending moments and shear forces were determined when the girders were damaged and compared with the limit values according to DIN 1052:2004-08. The disadvantages of the tested girders are discussed. It has been estimated that girders are not eligible for practical use.
W ocenie stanu technicznego obiektów bardzo rzadko występują silosy żelbetowe. Przedstawiona w artykule bateria silosów o znacznym stopniu zużycia zmuszała do wykonania badań nieniszczących i dobrania metod sprawdzających wytrzymałość poszczególnych jej elementów z podaniem sposobu naprawy.
EN
In the assessment of the technical condition very rare concrete silos. Presented in the article battery silos with a significant consumption forced to perform non-destructive testing and sizing methods for checking the strength of its individual elements specify how the repair.
12
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
W niniejszym artykule przedstawiono analityczne i numeryczne obliczenia mechanicznych właściwości obecnie opracowywanych prętów hybrydowych HFRP (Hybrid Fibre Reinforced Polymer) powstałych poprzez zastąpienie (substytucję) części włókien bazaltowych BFRP (Basalt Fibre Reinforced Polymer) włóknami węglowymi CFRP (Carbon Fibre Reinforced Polymer). W tym aspekcie termin ,,substytucja” rozumiany będzie jako modyfikacja prętów BFRP polegająca na zastąpieniu pewnej części włókien bazaltowych przez włókna węglowe. Celem analizy jest określenie optymalnego modelu prętów hybrydowych HFRP, które stanowiłyby realną alternatywę dla prętów stalowych stosowanych do zbrojenia konstrukcji betonowych. Zamiana włókien bazaltowych, włóknami węglowymi prowadzi do uzyskania lepszych właściwości mechanicznych prętów. Względy ekonomiczne skłaniają do ograniczenia procentowego udziału włókien węglowych w prętach HFRP do rozsądnej wielkości, oraz zastosowaniu włókien węglowych o stosunkowo niedużej wytrzymałości (Low Strength Carbon Fibres) jak na włókna CFRP. W pracy przedstawiony został opis struktury pręta hybrydowego, oszacowanie właściwości mechanicznych wzdłuż i w poprzek włókien, a także wpływ układu włókien w przekroju poprzecznym pręta na jego zachowanie mechaniczne. Analizę przeprowadzono dla różnych proporcji udziału włókien węglowych do włókien bazaltowych (1:9; 1:4; 1:3; 1:2; 1:1) w prętach HFRP. Rozpatrzono dwa przypadki rozmieszczenia włókien w przekroju poprzecznym pręta (Bar Architecture). Pierwszy z włóknami węglowymi zlokalizowanymi w rdzeniu, natomiast drugi z włóknami węglowymi usytuowanymi w powierzchniowej warstwie pręta.
EN
This paper introduces both an analytical and numerical study that investigates the mechanical performance of recently developing HFRP bars, which were created by substitution of the part of basalt fibres BFRP by the part of carbon fibres CFRP. In this aspect the term “substitution” might be understood as modification of BFRP bars, where part of basalt fibres will be replaced by carbon fibres. Substitution is aimed at achieving of better properties in obtained material. The objective of this study is to identify optimal model of HFRP bars, which provides an alternative to steel bars for enhancing concrete structures. Replacing of basalt fibres by carbon fibres provides better properties in mechanical performance of the bars. From economical point of view, for HFRP bars in combination with basalt fibres it is proposed to use carbon fibres with low strength (LS carbon fibres) and relatively small amount of volume fraction of carbon fibres to whole amount of fibres. This work represents description of the hybrid bar structure, estimation of properties of the bar in fibre and transverse directions and influence of fibre arrangement on mechanical properties of the bar. Analysis was performed for bars with different ratio between fibres of carbon and fibres of basalt (1:9; 1:4; 1:3; 1:2; 1:1). Investigations were done for two different bar architecture arrangements, where carbon fibres are estimated in the first case in the region near the edge and in another case in core region.
Zarządzanie kulturą organizacyjną decyduje o sukcesie lub porażce organizacji. Współczesne organizacje funkcjonujące w konkurencyjnym, rynkowym otoczeniu zmuszone są do szukania wszelkich możliwości uzyskania przewagi. W tym celu sięgają do innowacyjności, modernizacji i restrukturyzacji. Poszukują energii do przetrwania i rozwoju zarówno na zewnątrz, jak i wewnątrz organizacji. Ponieważ to ludzie stanowią najcenniejsze zasoby każdej firmy, wiec w ostatnich latach dużą popularność zyskuje pojęcie zarządzania przez kulturę. Organizacja, która potrafi zjednoczyć pracowników wobec wspólnych wartości i symboli i w ten sposób najpełniej wykorzystać ich wiedzę oraz motywacje ma dużą szansę na sukces rynkowy. Organizacje takie stawiają na pracowników, tworząc przy pomocy charyzmatycznych przywódców nowe wizje, inspiracje. Prawdziwi przywódcy są w stanie pociągnąć z sobą ludzi, rozwinąć ich zdolności i przystosować organizację przez zmianę kultury organizacyjnej do nieustannych zmian w otoczeniu. Zmiany w kulturze organizacyjnej wymagają raczej przywódcy niż managera. Termin przywództwo jest używany zwykle w sytuacjach kryzysu, zmiany, wyboru oraz podejmowania decyzji, za którymi idą wdrożenia nowych rozwiązań. W tego rodzaju sytuacjach znacznie skuteczniejszy jest przywódca niż dobrze zarządzający manager, skuteczny w codziennej, rutynowej pracy, pozbawionej niepewności i konieczności szczególnej mobilizacji wszystkich uczestników organizacji. Artykuł pozwala na przegląd definicji kultury organizacyjnej oraz jej funkcji. Wskazuje na konkretną wartość kultury organizacji i jej znaczący wpływ na sukces rynkowy lub porażkę.
EN
Managing culture of organization decides about success or failure an company. Contemporary company operating at competitive business environmental organizations must try to find any possibilities of advantage. In order to achieve these competitive advantages organizations using innovations and restructuring. Companies searching energy to survive and progression as well as inside and outside their structure. The most valuable resources of all organizations are employees because of that; recently, conception managing by culture became very popular. Company which is able to join employees around common values and symbols achieves goals. Organization which fully using skills and knowledge of employees can attain success at a market. Companies must put their money on employees, creating new visions and inspirations by charismatic leaders. Thru heads of organizations are able to get people to bring change, develop their skills and adapt company to permanent change in economic environment by changing organization culture. Culture of organization changes needed rather true leader than manager. The term leadership usually is using during crisis, changes, choice and decision taking when new solutions implemented. In that situations more effective is leader than manager doing his day by day routine job, without uncertain and necessity mobilization all organization’s members The paper lets review some definitions of organization’s culture and culture features. Highlighted precise value of organization culture and significant influence on market success or defeat.
14
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
W artykule przedstawiono integracje układu pomiaru stężenia dwutlenku węgla działającego pod kontrolą mikrokontrolera ARM z rdzeniem Cortex-M, z układem czujników chemicznych. Układ ten przewidziany jest do pracy w systemie czujników chemicznych platformy do badań zagrożeń CBRN (Chemicznych, Biologicznych, Radiologicznych i Nuklearnych). Platforma ta będzie modułem przeznaczonym dla robota mobilnego rozpoznania terenu i miejsc trudno dostępnych PIAP - Gryf. W artykule dokonano przeglądu metod pomiaru dwutlenku węgla i przygotowano wytyczne dotyczące doboru czujnika. Przedstawiono również schemat komunikacji poszczególnych modułów robota między sobą, wykorzystujący standard CAN oraz protokół MODBUS na interfejsie UART. Artykuł prezentuje również testy rozruchowe układu zamontowanego na robocie oraz uzyskane w trakcie testów wyniki.
EN
The paper presents integration of the carbon dioxide measurement system under the control of the ARM Cortex-M microcontroller, with a system of chemical sensors. The system is designed to operate with a platform of chemical sensors to examine CBRN (Chemical, Biological, Radiological and Nuclear) threats. The platform will form a module designed for a PIAP Gryf mobile robot for reconnaissance of field and places difficult to access. The paper reviews methods of carbon dioxide determination and specifies guidelines on sensor selection. A diagram is also presented of the communication between the individual modules of the robot which relies on the CAN standard, MODBUS protocol and UART interface. The paper also presents startup tests of the system installed in the robot and the obtained test results.
A prototyped dynamic weighing system has been presented which integrates together three advanced software environments: MATLAB, LabVIEW and iFIX SCADA. They were used for advanced signal processing, data acquisition, as well as visualization and process control. Dynamic weighing is a constantly developing field of metrology. Because of the highly complicated structure of any electronic weighing module, it is vulnerable to many sources of environmental disturbances. For this reason, there is a lot of research concerned with weighing signal processing, mechanical matters and functionality of the system. In the paper, some issues connected with dynamic weighing have been presented, and the necessity of implementing signal processing methods has been discussed. Implementation of this feature is impossible in the majority of SCADA systems. The integration of the three environments mentioned above is an attempt to create an industrial system with capabilities to deal with major dynamic weighing problems. It is innovative because it connects the industrial SCADA, laboratory/industrial product LabVIEW and MATLAB. In addition, the algorithms responsible for process control and data exchange are presented. The paper includes a description of the capabilities, performance tests, as well as benefits and drawbacks, of the system. The outcome of the research is a prototyped system and evaluation of its usefulness.
16
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
This paper presents a comparative analysis of experimental and theoretical deflections of simply supported beams reinforced with BFRP rebar (Basalt Fiber Reinforced Polymers). The tested BFRC model beams have been made of concrete class C30/37 and reinforced with flexural basalt bars of 8 mm in diameter with the characteristic identified in strength tests in tension. During the investigation of model beams there were registered beam deflection, concrete strains and width cracks, as well as critical forces. It has been shown that much lesser cross-sectional stiffness of basalt BFRP bars produces higher deflections and crack widths compared to the beams reinforced with steel bars of the same cross-section. The results of theoretical analysis of BFRC beam deflections on the basis of the known formulas showed some significant discrepancies compared to experimentally obtained deflections, especially for lower level of loading forces. The results clearly show that basalt rebar having full resistance against corrosion may be good alternative for the reinforcement of concrete structures, like RC bridge girders subjected to environmental attack.
Nowadays, due to emergence of cloud services, even the basic uses of personal computers may require the access to the Internet. In this paper modifications to Delay-Aware Network Utility Maximization System (DANUMS) are presented, which enable it to be deployed in an internetwork environment. The proposed solution consists of DANUMS and WiOptiMo systems, which cooperate by exchanging measurements of transmitted traffic in order to improve the network utility. Additionally, WiOptiMo enhances mobility by providing facilities for soft handover. Experiments presented in this paper illustrate the benefits gained from the integrated system application.
W pracy przedstawiono analizę porównawczą doświadczalnych i obliczonych teoretycznie szerokości rys w jednoprzęsłowych belkach swobodnie podpartych zbrojonych prętami bazaltowymi BFRP (Basalt Fibre Reinforced Polymers). Belki typu BFRP wykonano z betonu C30/37 ze zbrojeniem dolnym na zginanie prętami bazaltowymi o średnicy 8 mm, dodatkowo wykonano belki referencyjne ze zbrojeniem stalowym tej samej średnicy. Badano ugięcia i zarysowania oraz nośność belek zbrojonych prętami BFRP, o cechach wytrzymałościowych określonych w testach na rozciąganie. Wykazano, że znacznie zredukowana sztywność elementów zbrojonych prętami bazaltowymi BFRP wywołuje kilkakrotnie większe szerokości rys w porównaniu z belkami zbrojonymi prętami stalowymi o tym samym przekroju poprzecznym.
EN
This paper presents a comparative analysis of experimental and theoretical crack widths of simply supported beams reinforced with BFRP rebar (Basalt Fiber Reinforced Polymers). The tested BFRC model beams have been made of concrete class C30/37 and of bottom flexural basalt bars 8 mm in diameter. The reference RC beams with traditional flexural steel reinforcement have been additionally made of the same diameter. Beam deflections, concrete crack widths and strength capacity of beams reinforced with BFRP bars as well as with traditional steel bars have been registered. It has been shown that crack widths of beams reinforced with BFRP bars have been much (three to four times) higher than in the beams reinforced traditionally
The article presents technology used in making industrial floors and research connected with testing and calibration of the device for concrete trowelling start time measurements. The method allows to determine the start time of mash operations which result in improvment in the quality of the concrete surface expressed by its evennes. The method eliminated the workers subjective assessment and determines the precise starting point of machining operations.
PL
W artykule została przedstawiona technologia wykonania posadzek przemysłowych, a także badanie związane z testem oraz skalowaniem aparatu do badania czasu rozpoczęcia operacji zacierania. Metoda pozwala na wyznaczenie czasu rozpoczęcia operacji zacierania skutkującej podniesieniem jakości powierzchni betonowej wyrażonej jej równością. Metoda wyeliminowała subiektywną ocenę pracowników wykonujących posadzkę przemysłową - oraz określa w precyzyjny sposób moment rozpoczęcia operacji obróbczych.
20
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW