The quest for new sources of financing for the development of green economy sectors and enterprises is one of the challenges to effective management. This study verifies whether a relationship exists between the activity of selected companies who access the capital market in search for new financing sources, their development level and their competitive edge. The sample used in this study was composed of companies from the forestry and wood-based sector (a major part of the Polish economy) listed on the Warsaw Stock Exchange. The Technique for Order Preference by Similarity to an Ideal Solution (TOPSIS) was used to assess the development level of selected enterprises. The main recommendations were formulated based on the findings from the analysis of performance ratios and from the comparative and descriptive analysis of data on stock exchange transactions in the wood-based sector. This is because the assumption was made that by becoming more active in the capital market and, as a consequence, by strengthening their competitive position, the enterprises covered by this study may contribute to adding value in the circular economy.
2
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
The research discussed in the article involved the analysis of impedance characteristics originating from various non-standard defects detected in the material of an austenitic tube. Research-related test results were obtained when scanning a tube made of steel 316, using an internal probe and a MultiScan 5800 device. The tests involved the use of the classical ECT vortex current method applied to examine both the tube containing artificial defects, simulating the most common defects in industrial heat exchanger tubular inserts, and reference tubes containing standard defects. The non-standard defects (created artificially) simulated combinations of cracks, pits or other defects formed as a result of exposure to aggressive chemical and mechanical factors present in industrial conditions. The tests involved the scanning of the entire length of the tube at a constant rate. The tests were performed using a transient probe recording electrical impedance changes in a relative mode and in an absolute mode. The interpretation of results related to the non-standard defects was based on a comparison with the results obtained in relation to the standard reference defects. Values obtained in relation to the non-standard defects enabled, among other things, the identification of their volume and position in relation to the measurement probe. In most cases it was not possible to interpret the geometry of a given defect. The foregoing could be achieved using other non-destructive testing techniques.
PL
Dokonano oceny charakterystyk impedancyjnych pochodzących od różnych wad w materiale rury austenitycznej. Wskazania te otrzymano podczas badania rury ze stali 316 sondą wewnętrzną z wykorzystaniem aparatu MultiScan 5800. Zastosowano klasyczną metodę prądów wirowych ECT, badając zarówno rurę ze sztucznymi wadami symulującymi najczęściej spotykane uszkodzenia wkładów rurowych wymienników ciepła, jak również rury referencyjne, z i wadami standardowymi. Wytworzone sztucznie niestandardowe wady miały na celu odwzorowanie spotykanych w diagnostyce przemysłowej kombinacji pęknięć, wżerów lub innych ubytków powstałych w wyniku oddziaływań mechanicznych oraz działania agresywnych czynników chemicznych. Badania polegały na skanowaniu rury ze stałą prędkością, przy użyciu sondy przelotowej rejestrującej zmiany impedancji elektrycznej w trybie względnym i trybie absolutnym. Interpretacja uzyskanych wyników, dla wad niestandardowych, była oparta na analizie porównawczej z wynikami uzyskanymi dla standardowych próbek referencyjnych. Otrzymane wartości dla wad niestandardowych umożliwiły ich scharakteryzowanie, tj. określenie ich objętości oraz położenia względem sondy pomiarowej. W większości przypadków nie była możliwa interpretacja geometrii wady, a co jest możliwe przy zastosowaniu innych technik badań nieniszczących.
3
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
The article discusses complex tests of an actual pressure vessel after its long-lasting operation in a petroleum distillation system. As a result of exposure to extreme conditions, the structural material of the vessel degraded and corroded significantly. The corrosion damage was identified and imaged using a Phased Array technique-based ultrasonic method. The subsequent stage of investigation involved hydraulic tests and the recording of acoustic emission signals. Stress concentration fields in damaged areas were identified using the FEM-based simulation method. The test results will be used to develop the complex methodology enabling the evaluation of the technical condition of pressure vessels used in the petrochemical industry. The above-named objective constitutes the primary goal of Programme LEADER VII, funded by the National Centre for Research and Development.
PL
Wykonano kompleksowe badania stanowiskowe rzeczywistego zbiornika ciśnieniowego poddanego wieloletniej eksploatacji w instalacji destylacji ropy naftowej. Na skutek pracy w warunkach ekstremalnych materiał elementów konstrukcji urządzenia uległ degradacji oraz zawierał liczne uszkodzenia korozyjne, które zostały zidentyfikowane i odwzorowane za pomocą szczegółowych badań metodą ultradźwiękową z wykorzystaniem techniki Phased Array. Na dalszym etapie badań wykonano próby hydrauliczne z rejestracją sygnałów emisji akustycznej. W celu określenia stref o koncentracji pola naprężeń w obszarach uszkodzeń dodatkowo wykonano symulację metodą elementów skończonych. Wyniki wykonanych badań stanowią bazę do opracowania złożonej metodyki oceny stanu technicznego urządzeń ciśnieniowych przemysłu rafineryjnego – głównego celu projektu badawczego Programu LIDER VII sfinansowanego przez Narodowe Centrum Badań i Rozwoju.
Huta Bankowa, which is the only Polish manufacturer of rims for rolling stock manufacturers, as part of the development of its research potential and the quality of the products it offers, is planning to implement automated ring and rim ultrasonic testing technology in the near future. In this paper, the entire technological system of automated rim testing, owned currently by Huta Bankowa, was presented, with a special discussion of the ultrasonic examination stand. The assumptions concerning the designed testing system, using the latest technological solutions and selected results of numerical simulations of ultrasonic tests, made by CIVA software, on the basis of which the assumptions were made were also presented.
PL
Huta Bankowa, która jest jedynym polskim producentem obręczy przeznaczonych dla producentów taboru kolejowego, w ramach rozwoju swojego potencjału badawczego i podwyższenia jakości oferowanych wyrobów, w najbliższym czasie planuje wdrożyć technologię zautomatyzowanej kontroli jakości pierścieni i obręczy metodą ultradźwiękową. W ramach niniejszego artykułu zaprezentowano cały ciąg technologiczny badania obręczy w cyklu zautomatyzowanym, będący obecnie na wyposażeniu Huty Bankowej, ze szczególnym omówieniem stanowiska do badań ultradźwiękowych. Przedstawiono także założenia dotyczące projektowanego stanowiska badawczego, wykorzystującego najnowocześniejsze rozwiązania technologicznie oraz wybrane wyniki symulacji numerycznych badań ultradźwiękowych, wykonanych za pomocą oprogramowania CIVA, na których podstawie przeprowadzono weryfikację przyjętych założeń.
JavaScript jest wyłączony w Twojej przeglądarce internetowej. Włącz go, a następnie odśwież stronę, aby móc w pełni z niej korzystać.