Preferencje help
Widoczny [Schowaj] Abstrakt
Liczba wyników

Znaleziono wyników: 2

Liczba wyników na stronie
first rewind previous Strona / 1 next fast forward last
Wyniki wyszukiwania
help Sortuj według:

help Ogranicz wyniki do:
first rewind previous Strona / 1 next fast forward last
EN
This paper presents two methods of introducing boron into the surface layer of iron alloys, namely diffusion boronizing by means of the powder method and laser alloying with a TRUMPF TLF 2600 Turbo CO2 gas laser. Amorphous boron was used as the chemical element source. As regards diffusion drilling, the influence of temperature and time on the properties of the layer was tested. During the laser alloying, the influence of the thickness of the boriding paste layer as well as the power and laser beam scanning velocity was determined. How the carbon content in steel and alloying elements in the form of chromium and boron influence the structure of the surface layer was tested. To achieve this object, the following grades of steel were used: C45, C90, 41Cr4, 102Cr6, and HARDOX boron steel. The microhardness and wear resistance of the obtained boron-containing surface layers were tested. A Metaval Carl Zeiss Jena light microscope and a Tescan VEGA 5135 scanning electron microscope, a Zwick 3212B microhardness tester, and an Amsler tribotester were used for the tests. The structure of the diffusion- borided layer consists of the needle-like zone of FeB + Fe2B iron borides about 0.15 mm thick, with a good adhesion to the substrate of the steel subjected to hardening and tempering after the boriding process. After the laser alloying, the structure shows paths with dimensions within: width up to 0.60 mm, depth up to 0.35 mm, containing a melted zone with a eutectic mixture of iron borides and martensite, a heat affected zone with a martensitic-bainitic structure and a steel core. The microhardness of both diffusion-borided and laser-borided layers falls within the range of 1000 – 1900 HV0.1, depending on the parameters of the processes. It has been shown that, apart from the structure and thickness of the layer containing boron and microhardness, the frictional wear resistance depends on the state of the steel substrate, i.e. its chemical composition and heat treatment. The results of testing iron alloys in the borided state were compared with those obtained only after the heat treatment.
PL
W pracy przedstawiono dwie metody wprowadzania boru do warstwy wierzchniej stopów żelaza, a mianowicie borowanie dyfuzyjne z zastosowaniem metody proszkowej oraz stopowanie laserowe za pomocą lasera gazowego CO2 TRUMPF TLF2600 Turbo. Jako źródło pierwiastka użyto bor amorficzny. Zbadano w przypadku borowania dyfuzyjnego wpływ temperatury i czasu na właściwości warstwy. Przy stopowaniu laserowym określono oddziaływanie grubości warstwy pasty do borowania oraz mocy i szybkości posuwu wiązki laserowej. Przeanalizowano wpływ zawartości węgla w stali oraz dodatków stopowych w postaci chromu i boru na strukturę warstwy wierzchniej. W tym celu do badań zastosowano stale: C45, C90, 41Cr4, 102Cr6, stal borową HARDOX. Zbadano mikrotwardość oraz odporność na zużycie przez tarcie otrzymanych warstw wierzchnich zawierających bor. Do badań zastosowano mikroskop świetlny Metaval Carl Zeiss Jena i elektronowy mikroskop skaningowy Tescan VEGA 5135, mikrotwardościomierz Zwick 3212B oraz tribotester typu Amsler. Struktura dyfuzyjnej warstwy borowanej składa się z iglastej strefy borków żelaza FeB+Fe2B o grubości do ok. 0,15 mm o dobrej przyczepności z podłożem stali poddanej hartowaniu i odpuszczaniu po procesie borowania. Po stopowaniu laserowym w strukturze występują ścieżki o wymiarach: szerokość do 0,60 mm, głębokość do 0,35 mm, zawierające strefę przetopioną z mieszaniną eutektyczną borków żelaza oraz martenzytu, strefę wpływu ciepła o strukturze martenzytyczno-bainitycznej oraz rdzeń stali. Mikrotwardość warstw borowanych dyfuzyjnie i laserowo mieści się w zakresie 1000÷1900 HV0.1, w zależności od parametrów procesów. Wykazano, że poza strukturą i grubością warstwy zawierającej bor oraz mikrotwardością, odporność na zużycie przez tarcie zależy od stanu podłoża stali, czyli jej składu chemicznego i obróbki cieplnej. Wyniki badań stopów żelaza w stanie borowanym porównano z otrzymanymi tylko po obróbce cieplnej.
EN
This paper analyses the structure, hardness, and frictional wear resistance of surface layers formed on steels after hardfacing by means of the SSA arc method with self-shielded flux cored welding wire, with a content of carbon 5% and chromium 30% as well as boron alloying with the CO2 laser. S355J2 steel after being hardfaced with one up to three layers is characterized by the martensitic structure with chromium carbides and its surface hardness is 50–55HRC. In the weld deposit zone, with a thickness of up to approx. 2 mm, there is a constant distribution of hardness with the average value of 700 HV0.1, and then the hardness decreases to approx. 160 HV0.1 in the steel substrate. After hardfacing, the carbon content in S355J2 steel (0.23% wt.) increases to a similar content as in steel C90U in the initial state (0.96% wt.). After laser alloying with boron and after rapid cooling, C90U steel obtains distinctive paths with a zone structure and thickness reaching up to approx. 380 μm. In the remelted zone, there is a eutectic structure consisting of a mixture of iron borides and martensite with a hardness of approx. 1200–1800 HV0.1, and beneath it, there is heat affected zone with a martensitic-bainite structure with a hardness of approx. 700HV0.1. Hardfacing and laser heat treatment significantly decrease the frictional wear of the tested steels.
PL
W pracy przeanalizowano strukturę, twardość oraz odporność na zużycie przez tarcie warstw wierzchnich stali po napawaniu metodą łukową SSA drutem proszkowym samoosłonowym o zawartości węgla (5%) i chromu (30%) oraz stopowaniu borem za pomocą lasera CO2. Stal S355J2 po napawaniu jedną do trzech warstw charakteryzuje się strukturą martenzytyczną z węglikami chromu o twardości powierzchni 50÷55HRC. W strefie napoiny o grubości do ok. 2 mm występuje stały rozkład twardości o średniej wartości 700 HV0.1, po czym twardość spada w rdzeniu stali do ok. 160 HV0.1. Po napawaniu zawartość węgla w stali S355J2 (0.23% mas.) wzrasta do podobnej jak w stali C90U w stanie wyjściowym (0.96% mas.). Stal C90U po stopowaniu laserowym borem i szybkim ochłodzeniu uzyskuje charakterystyczne ścieżki o budowie strefowej i grubości dochodzącej do ok. 380 μm. W strefie przetopionej występuje struktura eutektyki będącej mieszaniną borków żelaza i martenzytu o twardości ok. 1100÷1800 HV0.1, a pod nią znajduje się strefa wpływu ciepła o strukturze martenzytyczno-bainitycznej i twardości ok. 700 HV0.1. Napawanie oraz laserowa obróbka cieplna w sposób istotny zmniejszają zużycie przez tarcie badanych stali.
first rewind previous Strona / 1 next fast forward last
JavaScript jest wyłączony w Twojej przeglądarce internetowej. Włącz go, a następnie odśwież stronę, aby móc w pełni z niej korzystać.