The aim of the study was to select the optimal content of zirconium introduced as an alloying additive to obtain the best strength properties of Al-Si alloy. A technically important disadvantage is the tendency of silumins to form a coarse-grained structure that adversely affects the mechanical properties of castings. To improve the structure, modification processes and alloying additives are used, both of which can effectively refine the structure and thus increase the mechanical properties. According to the Hall-Petch relationship, the finer is the structure, the higher are the mechanical properties of the alloy. The proposed addition of zirconium as an alloying element has a beneficial effect on the structure and properties of silumins, inhibiting the grain growth. The starting material was an aluminium-silicon casting alloy designated as EN AC-AlSi9Mg (AK9). Zirconium (Zr) was added to the alloy in an amount of 0.1%, 0.2%, 0.3%, 0.4% and 0.5% by weight. From the modified alloy, after verification of the chemical composition, samples were cast into sand moulds based on a phenolic resin. The first step in the research was testing the casting properties of alloys with the addition of Zr (castability, density, porosity). In the next step, the effect of zirconium addition on the structure and mechanical properties of castings was determined.
2
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
The possibilities of using low-temperature hydrogen-oxygen fuel cells with PEMFC proton-exchange membrane in transport and aviation were characterized and described. In this paper the emphasis was put on the investigation of energy efficiency of a commercial 5kW PEMFC fuel stack and on the possible directions to reduce the dimensions and weight of the PEMFC stack. Voltage dependencies were determined between voltage (U) -current (I) and current (I) - Power (P), as were the temperature distribution during the operation of the fuel cell stack and the peak current in humidifying the PEMFC stack by means of the SCU system. The energy demand of the 5kW fuel cell stack for the needs of the cooling system operation was determined (the so-called internal requirements of the fuel cell stack)
PL
W pracy scharakteryzowano możliwości zastosowania niskotemperaturowych wodorowo-tlenowych ogniw paliwowych z protonowymienną membraną PEMFC w transporcie i lotnictwie. W pracy nacisk położono na zbadanie efektywności energetycznej komercyjnego stosu ogniw paliwowych PEMFC o mocy 5kW, a także możliwe kierunki zmniejszania jego masy i gabarytów. Wyznaczono zależności napięcie (U)– prąd (I) oraz prąd(I)-moc (P), rozkład temperatur podczas pracy stosu ogniw paliwowych, a także wielkości prądu w „piku” podczas nawilżania stosu PEMFC za pomocą układu SCU. Wyznaczono zapotrzebowanie energetyczne stosu ogniw paliwowych 5kW na potrzeby pracy układu chłodzenia (tzw. potrzeby własne stosu ogniw paliwowych)
W artykule przedstawiono fragment wyników prac B+R realizowanych w Instytucie Odlewnictwa dotyczących opracowania nowoczesnych tworzyw odlewniczych ze stopów metali żelaznych i nieżelaznych do wykonywania podków o zwiększonej trwałości. Przedstawiono problemy związane z opracowaniem modelu ruchu konia i mechaniki kopyta. Na podstawie ogólnie dostępnych danych przeprowadzono analizy wytrzymałościowe podków wykonanych z wykorzystaniem technik odlewniczych.
EN
The article presents a fragment of results of R&D works carried out at the Foundry Research Institute concerning the development of modern casting materials from ferrous and non-ferrous alloys to make horseshoes with increased durability. Problems related to the development of the horse's movement model and hoof mechanics are presented. On the basis of generally available data, strength analyzes of horseshoes made using castings techniques were carried out.
Artykuł opisuje przygotowania i założenia do pierwszego w Polsce projektu pilotażowego zastosowania technologii BIM w GDDKiA przy projektowaniu i budowie odcinka drogi krajowej wraz z obiektami mostowymi i innymi branżami. Po omówieniu specyfiki i korzyści z użycia technologii BIM w projektach infrastrukturalnych opisano sam przedmiot pilotażu, którym była obwodnica Zatoru w ciągu drogi krajowej nr 28. W zakresie przygotowań do publicznego przetargu szczególny nacisk położony został na dialog techniczny z potencjalnymi wykonawcami oraz na dobór celów, jakie planowano osiągnąć, realizując cały projekt. Na koniec omówiono wymagania do przetargu oraz zaproponowane kryteria pozacenowe związane z technologią BIM.
EN
The article describes the preparations and assumptions for the first pilot project in Poland for the application of BIM technology in GDDKiA in the design and construction of a section of a national road, including bridges and other facilities. After discussing the specifics and benefits of BIM technology in infrastructural projects, the pilotage was described. It is the Zator bypass along the national road No. 28. In the scope of preparations for the public tender, special emphasis was placed on the technical dialogue with potential contractors and selection of goals that were planned to achieve with implementing the entire project. Finally, the requirements for the tender and the proposed non-price criteria related to the BIM technology are discussed.
5
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
In the article the methodology of forecasting the energy effects of the crosscutting process using the classical method, which takes into account the specific cutting resistance, is presented. The values of cutting power for the cross-cutting process of two types of wood (softwood and hardwood) were forecasted for the optimizing sawing machine with using presented methodology.The cross-cutting process with high values of feed speed was analyzed. The presented methodology allowed us to determine dimensions of the cut workpieces limited by the applied electric motor for both soft and hard wood.
PL
W artykule zaprezentowano metodologię prognozowania efektów energetycznych procesu poprzecznego przecinania drewna przy zastosowaniu metody klasycznej, która uwzględnia właściwy opór skrawania. Z wykorzystaniem prezentowanej metodyki zaprognozowano wartości mocy skrawania dla procesu przecinania poprzecznego dwóch typów drewna (drewno miękkie oraz drewno twarde) na optymalizerce. Analizy procesu poprzecznego przecinania drewna zostały przeprowadzone dla wysokich wartości prędkości posuwu. Zastosowana metodologia pozwoliła na określenie granicznych przekrojów przecinanego drewna dla zastosowanego silnika dla obydwu rodzajów przecinanego surowca, drewno twarde i miękkie.
In the underground mines of the Legnica-Głogów Copper District (LGOM) the main way to protect the room excavation is the use of a rock bolt support. For many years, it has proven to be an efficient security measure in excavations which met all safety standards and requirements. The article presents the consumption of the rock bolt support in the Mining Department “Polkowice-Sieroszowice” in the years 2010-2015 as well as the number of bolt supports that were used to secure the excavations. In addition, it shows the percentage of bolt supports that were used to conduct rebuilding work and cover the surface of exposed roofs. One of the factors contributing to the loss of the functionality of bolt supports is corrosion whose occurrence may lead directly to a reduction in the diameter of rock bolt support parts, in particular rods, bearing plates and nuts. The phenomenon of the corrosion of the bolt support and its elements in underground mining is an extremely common phenomenon due to the favorable conditions for its development in mines, namely high temperature and humidity, as well as the presence of highly aggressive water. This involves primarily a decrease in the capacity of bolt support construction, which entails the need for its strengthening, and often the need to perform the reconstruction of the excavation. The article presents an alternative for steel bearing plates, namely plates made using the spatial 3D printing technology. Prototype bearing plates were printed on a 3D printer Formiga P100 using the “Precymit” material. The used printing technology was SLS (Selective Laser Sintering), which is one of the most widely used technologies among all the methods of 3D printing for the short series production of the technical parts of the final product. The article presents the stress–strain characteristic of the long expansion connected rock bolt support OB25 with a length of 3.65 m. A rock bolt support longer than 2.6 m is an additional bolt support in excavations, and it is increasingly frequently used to reinforce roofs and in rebuilding the underground mines of KGHM Polish Copper S.A. In order to conduct the laboratory tests that are most suitable for the mine conditions, and yet are carried out on a laboratory test facility, the Authors used a steel cylinder with an external diameter of 102 mm and a length of 600 mm, which was filled with a core of rock (dolomite) from the roofs of the mine workings. In addition the maximum load that took over the bolt support made of rods and connected with sleeves was determined. For the initial tension, the elastic and plastic range of the maximal displacements, which were measured by the rope encoder, were determined. The statical tests of the expansion rock bolt support were carried out at the laboratory of the Department of Underground Mining in simulated mine conditions. The test facility enables the study of the long bolt rods on a geometric scale of 1:1 for the different ways of fixing. The aim of the laboratory research was to obtain the stress-strain characteristics, of the long expansion rock bolt support with a steel bearing plate and a plate printed on a 3D printer.
W artykule przedstawiono obecną sytuację gospodarki Stanów Zjednoczonych i perspektywy rozwoju po zmianie administracji rządowej. Wskazano na zagrożenia wynikające z konkurencji Meksyku, który staje się największym eksporterem produktów do USA. Wpływa to bezpośrednio na zmniejszenie PKB i wzrost bezrobocia w Stanach Zjednoczonych. Interwencja rządu - poprzez obniżenie podatków i wprowadzenie VAT - powinna wpłynąć pozytywnie na polepszenie wskaźników ekonomicznych. Motorem napędowym gospodarki Stanów Zjednoczonych - podobnie jak i Polski - są małe i średnie przedsiębiorstwa, których jest w USA 28 min. Przewiduje się, że zmiana przepisów odnośnie emisji szkodliwych substancji przez samochody powinna w sposób znaczący spowodować wzrost produkcji odlewów ciśnieniowych ze stopów aluminium jako tworzywa lekkiego i nadającego się w sposób ekonomiczny do powtórnego wykorzystania. Przemysł odlewniczy w 2016 roku odnotował znaczy wzrost produkcji dzięki rekordowo dużej produkcji samochodów, w tym również ciężarówek. Szacuje się, że w przemyśle odlewniczym brakuje ponad 4 min pracowników. Wynika to ze wzrostu produkcji oraz niskich zarobków w tej branży. Dlatego stawia się bardzo duży nacisk na automatyzację całego procesu. Wyzwaniem najbliższych lat będzie produkcja odlewów do samochodów elektrycznych, gdyż - według prognoz - ostatni samochód zasilany benzyną zostanie sprzedany w 2035 roku.
EN
The present situation of the United States economy and perspectives of its development after changing the government, is presented in the hereby paper. Hazards related to the Mexico competition, which becomes the largest exporter of products to the USA, are indicated. This directly decreases GDP (Gross domestic product) and causes an unemployment increase. Government intervention by lowering taxes and introducing of VAT (Value added tax) - should positively influence improvements of economic indices. The driving force of the US economy - in a similar fashion as of Poland - are small and medium enterprises, which number in the US equals 28 millions. It is expected that the change of regulations concerning emissions of harmful substances by cars should cause - to a significant degree - an increase of pressure die casting of aluminium alloys as a light material suitable for economic reusing. The foundry industry had a significant production increase in 2016 due to extremely large increase of the vehicle production, including trucks. It is estimated that there is a lack of 4 million of employees in the foundry industry. This results from the production increase and low salaries in this sector. Therefore a significant pressure is exercised on the process automating. Production of castings for electric cars will constitute the challenge of the nearest years, since - according to prognoses - the last car supplied by petrol will be sold in the year 2035.
Artykuł przedstawia wyniki badań odlewów z czterech stopów aluminium wykonanych z zastosowaniem technologii prasowania w stanie ciekłym. Do badań zastosowano stopy: EN AW 7022 (AlZn5Mg3- Cu) oraz jego modyfikację poprzez dodatek tytanu, A201.0, EN AC-4800 (AlSi13Mg1CuNi) oraz stop Al-Si-Zn według patentu PL 158900. Ze stopów wykonano odlewy z wykorzystaniem technologii prasowania w stanie ciekłym oraz – w celach porównawczych – odlewy kokilowe. Przeprowadzono badania podstawowych właściwości mechanicznych otrzymanych odlewów. W celu polepszenia ich właściwości mechanicznych przeprowadzono obróbkę cieplną według indywidualnie dobranych – w zależności od stopu – parametrów procesu. Parametry obróbki cieplnej dobrano na podstawie m.in. analizy wykresów DSC. Wykazano skuteczność technologii prasowania w stanie ciekłym do otrzymywania wysokowytrzymałych odlewów z badanych stopów.
EN
The article presents the results of investigations into castings made of four aluminum alloys produced with the use of squeeze casting technology. The investigations used the following alloys: EN AW 7022 (AlZn5Mg3Cu) and its modification with a titanium addition, A201.0, EN AC-4800 (AlSi13Mg1CuNi), Al-Si-Zn according to the patent PL 158900. The alloys were used to make castings with the use of squeeze casting technology and – for comparison – die castings. Investigations were performed on the basic mechanical properties of the obtained castings. In order to improve their mechanical properties, thermal treatment according to individually selected process parameters (depending on the alloy) was performed. The thermal treatment parameters were selected based on e.g. an analysis of the DSC diagrams. The tests proved the effectiveness of squeeze casting technology in obtaining high-strength casts made from the examined alloys.
9
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
Producenci pilarek formatowych do drewna dążą do zwiększania dokładności przecinania. Jedną z metod jest poprawa zachowania się wrzeciona, gdyż od niego w dużej mierze zależą efekty przecinania. Przedstawiono rozwój konstrukcji wrzecion pilarek w okresie ostatniego ćwierćwiecza. Opisano układ zmodernizowanego wrzeciona pilarki formatowej Fx550.
EN
Producers of sliding table saws constantly strive for improvement in sawing accuracy. One of the method is an upswing in a spindle behavior, since, it affects to a large degree sawing effects. The design development of sliding table saw spindles during the last quarter-century is presented. The spindle system of the modernized spindle of the sawing machine Fx550 is described.
Skanowanie wyrobów kształtowanych w technologii przyrostowej na bazie materiałów polimerowych wymaga odtworzenia pełnej geometrii z zachowaniem tekstury i kolorów. W artykule rozważono możliwość zastosowania fuzji danych pozwalającej na łączenie informacji pochodzącej z dwóch przyrządów pomiarowych, różniących się charakterystyką metrologiczną, właściwościami i specyfiką pracy. Przedstawiono fragment badań mających na celu ocenę wpływu wybranych czynników zewnętrznych kształtujących warunki pracy konkretnych modeli skanerów na jakość otrzymanych wyników. Wnioski z przeprowadzonych badań będą mogły być uwzględnione podczas dokonywania pomiarów tymi przyrządami, w celu wypracowania odpowiednio korzystnych wyników fuzji.
EN
Scanning the parts manufactured additive technique based on polymer materials requires to recreate the full geometry while maintaining the texture and colors. In the article analyzed the possibility of using data fusion technology that allows to combine Information coming from two measuring Instruments with metrological different characteristics, different properties, as well different specification of working. The authors show a part of research on the influence of some external factors forming the working conditions of concrete scanner models on the quality of their results. It is assumed that the conclusions of this study can be taken into account while measuring of these Instruments, In order to develop the favorable results of the data fusion.
W artykule zaprezentowano wybrane podkładki kotwowe stosowane w górnictwie podziemnym. Przedstawiono technologię drukowania przestrzennego 3D. Na podstawie analizy konstrukcji powszechnie stosowanych stalowych podkładek w górnictwie rudnym zaprojektowano i wydrukowano prototypową podkładkę na drukarce 3D Formiga P100 z zastosowaniem materiału PA 2200. Wydrukowaną podkładkę poddano badaniom ściskającym na maszynie wytrzymałościowej typu Walter+Bai 3000/200. W badaniach laboratoryjnych uzyskano charakterystykę obciążeniowo-przemieszczeniową. W podsumowaniu podano zalety i wady produkowania podkładek z wykorzystaniem drukarki 3D.
EN
This paper presents selected bolt bearing plates used in underground mining. The technology of 3D printing was presented. Basing on structural analyses of commonly used steel bearing plates in ore mining, prototype bearing plate was designed and printed with the 3D printer type Formiga P100 using PA 2200 material. The printed bearing plate was subject to compressive strength tests carried out with the Walter + Bai 3000/200 testing machine. In laboratory research, load-displacement characteristics were obtained. In conclusion, the advantages and disadvantages of producing bearing plate using a 3D printer were given.
12
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
W pracy scharakteryzowano właściwości i stan rozwoju technologii wodorowo-tlenowych niskotemperaturowych ogniw paliwowych (ang. polymer membrane fuel cell, PEMFC). Zbudowano laboratoryjny generator energii elektrycznej zawierający komercyjny stos ogniw paliwowych PEMFC FC-42 (Shunk, Niemcy) o mocy 360W chłodzony za pomocą medium ciekłego. Zbadano właściwości tego generatora w różnych warunkach eksploatacyjnych. Zaproponowano metodykę działań zmierzających do uproszczenia konstrukcji i masy tego generatora.
EN
In this paper the properties and current state of development of low-temperature hydrogen-oxygen fuel cells (polymer membrane fuel cells, or PEMFCs) are characterised. A 360W laboratory electric power generator was constructed, incorporating a commercial FC-42 PEMFC fuel stack (Shunk, Germany) and cooled with a liquid medium. The properties of this generator were studied in different operating conditions. A method of operation was proposed, aimed at simplification of the construction and weight of this generator.
13
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
Producenci pilarek formatowych do drewna dążą do zwiększania dokładności przecinania. Można to osiągnąć np. przez poprawę zachowania się wrzeciona, gdyż od niego w dużej mierze zależą efekty przecinania. Przedstawiono metodykę wyznaczania prędkości krytycznych wrzeciona pilarki formatowej w funkcji cech konstrukcyjnych wrzeciona i jego napędu.
EN
Producers of sliding table saws constantly strive for improvement in sawing accuracy. One of the method is an upswing in a spindle behavior, since, it affects to a large degree sawing effects. Methodology of determination of critical rotational speeds of the spindle in a function of the spindle design features and its driving system is presented.
W artykule omówiony został bieżący stan i problemy komunikacji miejskiej w Łodzi, historyczne przyczynki istniejących problemów oraz możliwości ich rozwiązania w ciągu kolejnych lat.
In the context of product development, the term rapid prototyping (RP) is widely used to describe technologies which create physical prototypes directly from digital data. Recently, this technology has become one of the fastest-growing methods of manufacturing parts. The paper provides brief notes on the creation of composites using RP methods, such as stereolithography, selective laser sintering or melting, laminated object modelling, fused deposition modelling or three-dimensional printing. The emphasis of this work is on the methodology of composite fabrication and the variety of materials used in these technologies.
An attempt was made to obtain ceramic preforms with different contributions of porosity. Compressive strength tests were carried out to estimate the ability of ceramic preforms to be utilised in the process of squeeze casting for the fabricating of metal matrix composites. The achieved ceramic preforms were subjected to the squeeze infiltration process, and materials with much higher mechanical properties relative to monolithic materials were obtained.
PL
Podjęto próbę uzyskania preform ceramicznych o różnym stopniu porowatości. Przeprowadzono badania ich wytrzymałości na ściskanie w celu określenia możliwości ich zastosowania w procesie otrzymywania kompozytów metalowo-ceramicznych technologią prasowania w stanie ciekłym. Otrzymane preformy poddano infiltracji ciśnieniowej i otrzymano kompozyty o znacząco wyższych właściwościach wytrzymałościowych w stosunku do odlewów monolitycznych.
Programy komputerowe są aktualnie powszechnym narzędziem wykorzystywanym podczas inżynierskich prac konstruktorskich i projektowych. Projektowanie form ciśnieniowych w oparciu o założenia konstrukcyjne detalu, dzięki możliwości tworzenia brył przestrzennych, umożliwia szybkie przygotowanie dokumentacji technologicznej. Konstruktor ciśnieniowych form odlewniczych, kierując się przesłankami technologicznymi, musi stworzyć odpowiednie warunki dla przepływającego ciekłego metalu, a z drugiej strony – zapewnić odpowiednie odpowietrzenie i chłodzenie formy ciśnieniowej. Możliwość wcześniejszej weryfikacji założeń konstrukcji wnęki formy ciśnieniowej oraz wizualizacja procesu jej wypełniania pozwala na skrócenie czasu, ograniczenie kosztów przygotowania i wdrożenia odlewu do produkcji. Na rynku światowym istnieje wiele programów pozwalających na prowadzenie analizy symulacyjnej procesu odlewania, krzepnięcia oraz innych zjawisk towarzyszących procesom kształtowania odlewu. W artykule przedstawiona została analiza zachowania się powietrza atmosferycznego w warunkach procesu odlewania pod wysokim ciśnieniem. Symulacje komputerowe przeprowadzono w programie Flow-3D, wykorzystując uproszczoną geometrię testową odlewu. Wyniki w postaci wizualizacji zostały przedstawione dla formy ciśnieniowej z oraz bez odpowietrzającej, inżektorowej wkładki „schodkowej”.
EN
Computer programs are now a common tool aiding the engineer’s work on structure design. The design of foundry moulds used in the pressure die casting process, based on the casting design and effectively utilising the ability to create 3D images of solid bodies, allows for quick preparation of technological documentation. The designer of foundry moulds, guided by technological premises, has to create the right conditions for the liquid metal flow and ensure proper die venting and cooling mould pressure. The possibility of early verification of the die cavity design with visualization of how it will be filled with molten metal reduces both time and cost of the casting preparation and implementation into production. There are many programs on the world market that perform simulation and analysis of pouring, solidification, and other phenomena and operations accompanying the casting shaping process. This article presents an analysis of ambient air behaviour under conditions of high pressure die casting. Computer simulations were performed using Flow-3D software on a test casting of simplified geometry. The results were displayed in a visual form for the die with and without the “stepped” venting injector insert.
18
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
W ostatnich latach, zwłaszcza po wejściu Polski do Unii Europejskiej, podejmowane są różnorodne działania mające służyć poprawie klimatu i ochronie środowiska naszej planety, szczególnie przez ograniczenie emisji gazów cieplarnianych do atmosfery, w tym CO2 związane z wykorzystaniem w energetyce paliw kopalnych. W związku z tym obserwujemy dążenie do poszukiwania rozwiązań pozwalających na korzystanie np. z alternatywnych źródeł energii, które zarówno są przyjazne środowisku naturalnemu, jak i przyczyniają się do zachowania kopalnych surowców energetycznych dla przyszłych pokoleń. Do realizacji tych celów mogą być odpowiednio dobierane nowoczesne rozwiązania oparte na odnawialnych źródłach energii, np. na biogazie powstającym w procesach beztlenowej fermentacji metanowej osadów, jak też pompach ciepła, dla których źródłem pierwotnym ciepła może być energia zawarta w wodzie wodociągowej lub ściekach. Instalacje te mają swój sens wszędzie tam, gdzie są rentowne. Szczególnie wykorzystanie biogazu znajduje coraz szersze zastosowanie na oczyszczalniach ścieków w branży wodociągowo-kanalizacyjnej.
19
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
W artykule przedstawiono zastosowanie techniki konsolidowania informacji na podstawie danych, pozyskanych z dwóch źródeł metodą skanowania, której rezultaty wykorzystano w procesie cyfrowego dokumentowania obiektu z uszkodzonymi powierzchniami. W pomiarach zastosowano dwa mobilne systemy współrzędnościowe: ramię pomiarowe firmy ROMER z laserową głowicą skanującą typu RS- 2, oraz system ScanBrightTM firmy SmartTech, wyposażony w skaner światła białego. W pierwszym przypadku oprogramowaniem zarządzającym i przetwarzającym dane był pakiet Geomagic Studio, w drugim oprogramowanie Mesh3d. Systemy te pozwalają rejestrować dane w formatach tekstowych, gdzie każdy pojedynczy próbkowany punkt opisany jest wartościami XYZ, a w oprogramowaniu Mesh3d dodatkowo składowymi koloru RGB, dlatego informacje zawarte w tych plikach w różnym stopniu odwzorowują mierzone powierzchnie.
EN
The article describes the use of the technology consolidating the information from data obtained by scanning from two different sources, the results of which were used in the process of visually reconstructing the part with damaged surfaces. The measurement uses two mobile coordinate systems: ROMER measuring arm, equipped with the laser scanner RS-2, and the system SmartBright SMARTTECH, having a white light scanner. In the first case as management software and data processing a package Geomagic Studio was used, in the second Mesh3d software. These systems allow you to register data in text format, where every single scanned point is described by coordinate values of XYZ, and additionally Mesh3d allows to record of the RGB color components.
20
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
Współczesne urządzenia protetyczne projektowane są w taki sposób, aby w szeregu kilku typów rozmiarów były dopasowane do wszystkich możliwych pacjentów, a tym samym niestety nie zapewniają odpowiedniego indywidualnego komfortu i funkcjonalności. Dzięki wykorzystaniu metod inżynierii odwrotnej i szybkiego prototypowania możliwe jest aby poszczególne ortezy dostosować do indywidualnego pacjenta i jego choroby, zapewniając jednocześnie odpowiednie nowoczesne wzornictwo. Współczesne skomputeryzowane techniki wytwarzania ortez dla indywidualnego pacjenta mogą zapewnić odpowiedni komfort użytkowania jak również pozwolić na zmianę wzornictwa dla każdego pacjenta sposobnie do jego wymagań.
EN
Orthotic devices are currently designed to fit a range of patients and therefore they do not provide individualized comfort and function. Using RP methods it is possible to make individual orthosis devices tailored to the individual patient and the disease also characterized by the modern design. A computerized technique for fabricating patientspecific orthotic devices has the potential to provide excellent comfort and allow for changes in the standard design to meet the specific needs of each patient. Reverse engineering methods are combined with rapid prototyping to create patient-specific orthoses. A novel process was engineered to utilize patient-specific surface data of the patient anatomy as a digital input, manipulate the surface data to an optimal form using CAD software, processing also for modern looking and check strength and then processing in rapid prototyping machine for fabrication.
JavaScript jest wyłączony w Twojej przeglądarce internetowej. Włącz go, a następnie odśwież stronę, aby móc w pełni z niej korzystać.