Preferencje help
Widoczny [Schowaj] Abstrakt
Liczba wyników

Znaleziono wyników: 16

Liczba wyników na stronie
first rewind previous Strona / 1 next fast forward last
Wyniki wyszukiwania
help Sortuj według:

help Ogranicz wyniki do:
first rewind previous Strona / 1 next fast forward last
EN
The paper presents results of measuring heat diffusivity and thermal conductivity coefficients of used green foundry sand in temperature range ambient – 600°C. During the experiments a technical purity Cu plate was cast into the green-sand moulds. Basing on measurements relationships of the measured properties were evaluated. It was confirmed that the obtained relationships are complex and that water vaporization strongly influences thermal conductivity of the moulding sand in the first period of the mould heating by the poured and solidified casting.
EN
The paper presents results of measuring thermal conductivity of green sand mould material and time of castings solidification evaluated from cooling curves. During the experiments pure Cu (99,8 %) plate was cast into the examined sand moulds. Basing on the measurements it was stated that thermal conductivity of the moulding sand has complex temperature variability, especially during the water vaporization. It was confirmed that water vaporization strongly influences thermal conductivity of the moulding sand in the first period of the mould heating by the poured casting. The obtained dependence should be used in the numerical calculations to improve their accuracy.
PL
Artykuł prezentuje wyniki pomiarów współczynnika przewodzenia ciepła materiału wilgotnej formy piaskowej z bentonitem oraz czas krzepnięcia odlewu płyty z miedzi o czystości 99.8%. Na podstawie eksperymentów stwierdzono, że temperaturowa zależność przewodności cieplnej badanej masy formierskiej nie ma prostego przebiegu, szczególnie w okresie odparowywania wilgoci, a uzyskana w części eksperymentalnej temperaturowa zależność powinna być stosowana w obliczeniach numerycznych w celu polepszenia jakości obliczeń.
EN
An experimental investigation was conducted to observe and analyze the microstructural evolution of phases present in the AK64 Al-Si-Cu alloy subjected to a modified T6 heat treatment (HT). The AK64 alloy1 is the Polish alternative of the A319.0 ASM standard aluminium alloy. The modified T6 HT schedule with a higher temperature and shorter duration was applied in the solutioning process and lower quenching and higher artificial ageing temperature than the prescribed by the ASM standard were used. The cooling curves registered during the liberating of overheating and solidifying processes give important information on nucleation temperatures for the Al dendrite network, Al-Si eutectic reaction and precipitation of Cu-rich phases. Comparison of the as-cast and heat treated microstructures revealed predicted microstructural changes and also partial fragmentation of the Fe-rich phases was observed after the application of the modified HT programme.
PL
Artykuł poświęcony jest obróbce cieplnej stopu AK64, który jest odpowiednikiem stopu ASM: A319.0. W badaniach zastosowano zmodyfikowaną obróbkę cieplną T6 o podwyższonej (w stosunku do procedury T6 HT – ASM) temperaturze wyżarzania i skróconym czasie starzenia naturalnego po przesyceniu w wodzie. Obserwacje struktury stopu po obróbce cieplnej wykazały dużą zgodność ze strukturami przewidzianymi na podstawie przeprowadzonych symulacji numerycznych. Dodatkowo określono wartości temperatury odpowiadającej początkowi zarodkowania fazy α(Al), reakcji eutektycznej Al-Si oraz wydzielania z roztworu fazy bogatej w Cu. Opisano również częściową fragmentację fazy zawierającej Fe, będącą następstwem zastosowanej zmodyfikowanej obróbki cieplnej.
PL
Stopy Zn-Al charakteryzują się wieloma pozytywnymi cechami, między innymi zdolnością do tłumienia drgań, co stawia je w grupie tworzyw o zaawansowanych właściwościach. W stanie po odlaniu, zwłaszcza do form piaskowych stopy Zn-Al cechuje niekorzystna ze względu na właściwości plastyczne silnie dendrytyczna struktura. Aby zmienić charakterystykę wydzieleń dendrytycznych a jednocześnie rozdrobnić ziarno stosuje się zabieg modyfikowania struktury stopu. Najlepsze efekty uzyskuje się wprowadzając do ciekłego stopu obce cząstki Ti w zaprawach. W technologii stopów Zn-Al wykorzystuje się zaprawy znane z technologii stopów Al-Zn oraz nowe zaprawy Zn-Ti, które charakteryzują się bardzo dobrą rozpuszczalnością w temperaturach topienia stopów Zn-Al oraz zbliżoną gęstością. W artykule prezentowane są wyniki badań dla stopu Zn - 10%Al, który został zmodyfikowany zaprawą AlTi3C0,15 oraz zaprawą ZnTi3,2. Najpierw wytopiono stop wstępny ZnAl10 a następnie prowadzono jego modyfikację. Obydwie zaprawy wprowadzane były do stopu w taki sposób, aby dostarczyć 25, 50, 100, 200 i 400 ppm Ti. Stop wyjściowy i po modyfikacji odlewane były do suszonych form zbudowanych z klasycznej masy formierskiej. Próbki po wybiciu z formy obrabiane były mechanicznie a następnie badane. W celu wyznaczenia współczynnika tłumienia prowadzane były badania ultradźwiękowe. Wytrzymałość na rozciąganie oraz wydłużenie badane były na maszynie wytrzymałościowej Instron 6025. Zestawienie wyników pozwoliło porównać skuteczność modyfikacji daną zaprawą, oraz ich wpływ na daną właściwość stopu. W znacznej części badania dowodzą tego, że obydwie zaprawy działają w bardzo podobny sposób i wywierają podobny wpływ na właściwości stopu ZnAl10.
EN
Zn-Al alloys are characterised by several positive features, among others by the ability of damping vibrations, which situates them in the group of materials of advanced properties. In as cast condition, especially in sand moulds, Zn-Al alloys have strongly dendritic structure which is disadvantageous on account of their plastic properties. In order to change the characteristic dendritic precipitates and simultaneously to refine grains, the procedure of modifying the alloy structure is applied. The best effects are obtained when Ti particles contained in inoculants are introduced into liquid alloys. The inoculants known from the Al-Zn alloys technology, as well as new Zn-Ti inoculants characterised by very good solubility at melting temperatures of Zn-Al alloys and by similar density, are applied in the Zn-Al alloys technology. The results of investigations of the Zn - 10%Al alloy, which was modified by the AlTi3C0,15 and ZnTi3,2 inoculants, are presented in the hereby paper. The master foundry alloy ZnAl10 was at first melted and then its modification was performed. Both inoculants were introduced into the alloy in such way as to supply 25, 50, 100, 200 and 400 ppm of Ti. The master alloy and the alloy after the modification were cast into dry moulds made of the classic moulding sand. The samples, after knocking out from the mould, were subjected to mechanical working and then investigated. To determine the damping coefficient ultrasound tests were performed. The tensile and elongation strengths were tested by the testing machine Instron 6025. The compilation of results allowed to compare the efficiency of the modification by the given inoculant and their influence on the given property. Investigations, in a significant part, prove that both inoculants operate in a very similar fashion and have a similar influence on the ZnAl10 alloy properties.
EN
The paper presents results of measuring attenuation coefficient of the Al-20 wt.% Zn alloy (AlZn20) inoculated with different grain refiners. During experiments the melted alloys were doped with Al-Ti3-C0.15 refining master alloy. Basing on measurements performed by Krautkramer USLT2000 device with 1MHz ultrasound wave frequency it was stated that grain refinement reduces the attenuation coefficient by about 20-25%. However, the examined alloys can be still classified as the high-damping ones of attenuation greater than 150 dB/m.
EN
The paper presents results of measuring thermal conductivity and heat capacity of bentonite foundry sand in temperature range ambient – 900 °C. During the experiments a technical purity Cu plate was cast into the green-sand moulds. Basing on measurements of the mould temperature field during the solidification of the casting, the temperature relationships of the measured properties were evaluated. It was confirmed that water vaporization strongly influences thermal conductivity of the moulding sand in the first period of the mould heating by the poured casting.
7
Content available Thermo-Physical Properties of Selected Inconel
EN
The paper brings results of examinations of main thermo-physical properties of selected Inconel alloys, i.e. their heat diffusivity, thermal conductivity and heat capacity, measured in wide temperature range of 20–900°C. Themathematical relationships of the above properties vs. temperature were obtained for the IN 100 and IN 713C alloys. These data can be used when modelling the IN alloys solidification processes aimed at obtaining required structure and properties as well as when designing optimal work temperature parameters.
PL
Praca dotyczy badań głównych właściwości termofizycznych wybranych stopów typu Inconel, to jest dyfuzji ciepła, przewodności cieplnej i ciepła właściwego, mierzonych w szerokim zakresie temperatury 20–900°C. Matematyczne zależności ww. właściwości w funkcji temperatury dotyczą stopów IN 100 oraz IN 713C. Uzyskane w badaniach dane mogą być wykorzystane podczas numerycznego modelowania krzepnięcia i projektowania stopów typu IN o pożądanej strukturze i właściwościach a także projektowania optymalnych temperaturowych parametrów pracy.
EN
The paper is devoted to examinations of the refining efficiency of fluxes and refiners applied during melting of zinc and zinc-aluminium alloys. The content of gases, mainly hydrogen, in the alloys not protected during the charge melting and in the ones protected with the fluxes and/or refined is discussed. The performed examinations show that using the protecting fluxes and melt-refining before pouring leads to significant improvement of ductility in Zn and binary Zn-Al alloys as well as significant increase of the material clearness confirmed by increased density. Furthermore, the metallurgical yields are also increased.
PL
Praca poświęcona jest badaniom rafinacyjnej skuteczności żużli ochronnych i rafinatorów stosowanych w technologii przetapiania cynku oraz stopów cynk-aluminium. Wykonane badania wykazały, iż Zn i stopy podwójne Zn-Al przetapiane pod żużlami ochronnymi oraz przerafinowane przed odlaniem do formy wykazują zwiększoną plastyczność i zwiększoną czystość, potwierdzoną podwyższoną gęstością masy. Dodatkowo, wzrastają uzyski metalurgiczne.
EN
The paper presents results of measuring thermal conductivity of sand mould material and time of castings solidification evaluated from cooling curves and from Nova Flow & Solid numerical calculations. During the experiments pure Al (99,95%) plate was cast into the sand moulds. The analysed variable parameter in numerical calculations was mould thermal conductivity of fixed value taken from the range 0.5-0.9 W/(mK). Other mould parameters (initial temperature, mass density, heat capacity) and thermo-physical properties of liquid and solid casting were taken invariable. Basing on the measurements it was stated that thermal conductivity of the moulding sand has complex temperature variability, especially during the water vaporization and the obtained dependence should be used in the numerical calculations to improve their accuracy.
PL
Artykuł prezentuje wyniki pomiarów współczynnika przewodzenia ciepła materiału formy piaskowej oraz czas krzepnięcia odlewu oszacowany z krzywej stygnięcia i obliczony numerycznie za pomocą Nova Flow & Solid. W czasie eksperymentów odlew w kształcie płyty wykonywano z czystego aluminium (99,95%). Zmienna w obliczeniach była przewodność cieplna materiału formy z zakresu 0,5-0,9 W/(mK). Pozostałe parametry formy (temperatura początkowa, gęstość masy i pojemność cieplna) oraz właściwości termofizyczne ciekłego i zakrzepłego metalu były stałe. Na podstawie eksperymentów stwierdzono, że temperaturowa zależność przewodności cieplnej formy nie ma prostego przebiegu, szczególnie w okresie odparowywania wilgoci, a uzyskana w części eksperymentalnej temperaturowa zależność powinna być stosowana w obliczeniach numerycznych w celu polepszenia jakości obliczeń.
EN
The paper presents results of measuring thermal conductivity of green-sand mould material and time of pure-copper plate castings solidification evaluated from cooling curves. During the experiments pure Cu (99,8 %) plate was cast into the green-sand moulds. Basing on the measurements it was stated that thermal conductivity of the moulding sand has complex temperature variability, especially during the water vaporization and the obtained dependence should be used in the numerical calculations to improve their accuracy.
EN
Cast alloys on the Zn matrix and of an increased Al content are characterised by good technological and mechanical properties, due to which they should meet special, more demanding requirements. However, the basic problem in these alloys technology, apart from a high tendency for gases pick-up and oxidation of liquid metals, is a tendency to form coarse-grained dendritic structures in castings solidifying in sand moulds, what - in turn - unfavourably influences their plastic properties [1, 2, 7, 11]. Therefore several treatments aimed at obtaining fine-grained structure and improving plastic properties are applied in these alloys technology. The presented study concerns the modification process of binary, middle-aluminium Zn alloys performed by additions of inoculants containing titanium and investigations of these modifications influence on the structure refinement degree. The Zn-10wt% Al (ZnAl10) alloy modified, before pouring into a sand mould, either by addition of the traditional inoculant i.e. Al-3wt% Ti-0.15wt% C (AlTi3C0.15 – TiCAl) or the new inoculant Zn-3.2wt% Ti (ZnTi3.2) was tested. Within investigations the thermal analysis was performed, especially cooling curves and their first derivatives, and also measurements by means of the differential scanning calorimetry (DSC), with a purpose of determining the modification influence on undercooling degree changes. Microstructures of the tested alloy were observed by the light microscopy (LM). The applied modification of middle-aluminium zinc alloys by AlTi3C0.15 and ZnTi3.2 inoculants causes a significant refinement of the alloy structure. Inoculants applied in investigations have a strong nucleating activity, which is confirmed by decreasing of undercooling and the temperature recalescence in cooling curves, which occurs simultaneously with grain refinements.
EN
The paper is devoted to grain-refinement of the medium-aluminium zinc based alloys (MAl-Zn). The system examined was sand cast Zn-10 wt. %. Al binary alloy (Zn-10Al) doped with commercial Al-3 wt. % Ti – 0.15 wt. % C grain refiner (Al-3Ti-0.15C GR). Basing on the measured attenuation coefficient of ultrasonic wave it was stated that together with significantly increased structure fineness damping decreases only by about 10 – 20%. The following examinations should establish the influence of the mentioned grain-refinement on strength and ductility of MAl-Zn cast alloys.
PL
Publikacja dotyczy zabiegu modyfikowania podwójnych stopów Zn o średniej zawartości aluminium dodatkiem zaprawy zawierającej tytan i obejmuje badania wpływu zabiegu modyfikowania na stopień rozdrobnienia mikrostruktury stopu Zn-10% mas. Al (ZnAl10) odlewanego do formy piaskowej. Badany stop został rozdrabniany zaprawą modyfikującą Zn – 3,2% mas. Ti, wprowadzającą do metalu Ti. Na podstawie dokonanej oceny obrazów mikrostruktury stopu wyjściowego niemodyfikowanego i zmodyfikowanego zmiennym dodatkiem Ti zawartego w zaprawie modyfikującej stwierdzono, że zastosowana zaprawa modyfikująca powoduje określone, w zależności od ilości wprowadzonego do stopu Ti, rozdrobnienie ziarna stopu w stosunku do stopu wyjściowego niemodyfikowanego. Z kolei wyniki uzyskane w przeprowadzonej analizie termicznej potwierdzają zarodkotwórcze działanie użytej do badań zaprawy.
EN
The paper deals with grain-refinement of the sand-cast binary medium-aluminium Zn-10 mas. % alloy (ZnAl10) by using the Zn-3.2 mas. %Ti master alloy. Basing on the structure analysis it was stated that the master alloy causes significant grain-refinement in comparison with the initial, no modified alloy. Thermal analysis of the cooling curves stated that the modified alloys had increased nucleation temperatures and, at the same time, decreased recalescence – which proves nucleating action of the Zn-3.2 mas. %Ti master alloy in the examined alloy.
PL
Celem pracy była ocena możliwości zastąpienia czasochłonnej technologii kucia głowicy Pollaxe poprzez odlanie przedmiotu przy użyciu staliwa. W ramach przeprowadzonych badań wykonano szereg symulacji komputerowych mających na celu optymalizację technologii. Uzyskane wyniki ukazały nam możliwość poprawnego wykonania odlewu. Odlewanie umożliwia przyśpieszenie procesu produkcji i zmniejszenie kosztów wytwarzania głowicy, co jest odpowiedzią na rosnące zapotrzebowanie na tego typu repliki broni białej przez muzea oraz grupy rekonstrukcji historycznej.
EN
Aim of this study was to evaluate the possibility of making steel Pollaxe head by replacing the time-consuming forging witch casting technology. As part of research, a series of computer simulations aimed at optimizing and reducing the manufacturing costs of the head were made. Current work constitute a response to the growing demand for this type of replica edged weapons by museums and historical reenactment groups.
15
Content available remote DSC and TA characteristics of the inoculated Al-Zn20 alloy
EN
The paper brings information about inoculation process of the sand-cast binary Al-20 wt% Zn (AlZn20) alloy, inoculated with Ti-containing grain-refiners, i.e. AlTi5B1, AlTi3C0.15 and (AlZn)-Ti3 master alloys (MA). During the experiments thermal analyses (TA) and differential scanning calorimetry (DSC) were used. Macrostructure observations were performed using light microscopy (LM). On the basis of the performed examinations it was found that all the MAs used in this work caused significant grain refinement, which initiates via a heterogeneous nucleation mode. The obtained structure fineness of the inoculated AlZn20 alloy should positively influence its ductility, which is of great importance for the practical application of this group of foundry alloys.
EN
Pressure die casting has become the next area of experimentation on virtual models in computer memory. The article presents an attempt to optimize the manufacturing process of an item made of magnesium AZ91D alloy, which was cast using the pressure technology on a machine with a hot pressing chamber. Special attention was paid to the flow velocity in individual parts of the gating system and in the mould cavity, as well as to the air evacuation from the mould cavity. The aim was to achieve a flawless casting, especially in terms of porosity.
PL
Odlewnictwo ciśnieniowe stało się kolejnym obszarem objętym możliwością przeprowadzania eksperymentów wirtualnych za pomocą komputerów. W artykule przedstawiono próbę optymalizacji procesu wytwarzania elementu wykonanego ze stopu magnezu AZ91D, który odlewany był w technologii odlewania ciśnieniowego w urządzeniu z gorąca komorą prasowania. Szczególną uwagę zwrócono na prędkość przepływu w poszczególnych elementach układu wlewowego i w przestrzeni wnęki formy, jak również na ewakuację powietrza z wnęki formy. Nadrzędnym celem pracy było uzyskanie odlewu bez wad wewnętrznych, ze szczególnym wskazaniem na porowatość.
first rewind previous Strona / 1 next fast forward last
JavaScript jest wyłączony w Twojej przeglądarce internetowej. Włącz go, a następnie odśwież stronę, aby móc w pełni z niej korzystać.