Przedstawiono uogólnioną metodę modelowania uplastyczniania tworzyw polimerowych w procesie wytłaczania, niezależną od sposobu wytłaczania i niewymagającą znajomości mechanizmu uplastyczniania. Proponowana metoda polega na modelowaniu przepływu dwufazowego (płyn/ciało stałe) jako przepływu jednofazowego, w którym materiał występuje w stanie stałym lub płynnym, w zależności od warunków przepływu. Zastosowano równanie reologiczne Crossa-WLF (Williamsa-Landela-Ferry’ego), umożliwiające zdefiniowanie tworzywa w stanie stałym jako płynu o dużej lepkości, natomiast tworzywa w stanie uplastycznionym jako płynu o małej lepkości. Zagadnienie rozwiązywano w odniesieniu do wytłaczania jednoślimakowego, z założeniem przepływu nienewtonowskiego, trójwymiarowego, nieizotermicznego, z zastosowaniem narzędzi obliczeniowej mechaniki płynów (ang. CFD, Computational Fluid Dynamics). Przebieg uplastyczniania był definiowany przez rozkład temperatury płynu, wyznaczający obszar ciała stałego i obszar płynu.
EN
A procedure of general modeling of polymer melting in extrusion process has been presented. The procedure is independent on the type of extrusion, and does not require any knowledge of melting mechanism. The procedure involves modeling the two-phase flow (fluid/solid) as a single-phase flow in which the material, depending on the flow conditions, is solid or fluid. Cross-WLF rheological model has been used, which defines the solid polymer as a high viscosity fluid, while the polymer melt as a low viscosity fluid. The problem has been solved for single screw extrusion process as a three-dimensional, non-isothermal, non-Newtonian flow using CFD (Computational Fluid Dynamics) software. Melting progress is defined by the temperature distribution which determines the regions of solid and fluid.
2
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
Przedstawiono zagadnienie komputerowego modelowania procesu wytłaczania dwuślimakowego współbieżnego z zastosowaniem niekonwencjonalnych układów ślimakowych. Opisano przepływ tworzywa w wytłaczarce dwuślimakowej współbieżnej. Podano przykłady trójwymiarowego, nienewtonowskiego modelowania wybranych elementów niekonwencjonalnych. Do modelowania wykorzystano pakiet programów obliczeniowej mechaniki płynów ANSYS Polyflow.
EN
Computer modeling of co-rotating twin screw extrusion with the use of nonconventional screw configurations has been presented. The polymer flow in the co-rotating twin screw extruder has been described. Some examples of three-dimensional, non-Newtonian modeling are shown. CFD generally oriented software ANSYS Polyflow has been used for modeling.
3
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
Przedstawiono zagadnienie komputerowego modelowania procesu wytłaczania dwuślimakowego przeciwbieżnego z zastosowaniem niekonwencjonalnych układów ślimakowych. Podano przykłady trójwymiarowego, nienewtonowskiego modelowania wybranych elementów niekonwencjonalnych. Zastosowano ogólnie zorientowany pakiet programów obliczeniowej mechaniki płynów CFD (computational fluids dynamics) – ANSYS Polyflow. Opisano metodę globalnego modelowania wytłaczania przeciwbieżnego, które ujmuje ten proces całościowo, z uwzględnieniem transportu tworzywa w stanie stałym, uplastyczniania tego tworzywa oraz jego przepływu po uplastycznieniu. Metoda ta bazuje na bezwymiarowych charakterystykach przepływowych ślimaków, definiujących zależności bezwymiarowego natężenia przepływu tworzywa i bezwymiarowego gradientu ciśnienia.
EN
Computer modeling of counter-rotating twin screw extrusion with the use of nonconventional screw configurations has been presented. Some examples of three-dimensional, non- -Newtonian modeling are shown. CFD generally oriented software ANSYS Polyflow has been used for modeling. Global modeling of counter-rotating extrusion is discussed which describes the process considering solid transport, melting and melt flow. The basis of this approach were screw pumping characteristics which defined the dimensionless flow rate and dimensionless pressure gradient.
4
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
We present results of small-signal measurements and modeling of GaN FET devices manufactured by Institute of Electronics Materials Technology (ITME). The devices have 500 nm gate length and 100 μm gate width and are grown on 350 μm sapphire substrate. We measured scattering parameters of the devices on-wafer in the frequency range 0.01-15 GHz, and then extracted parameters of their small-signal equivalent circuits. These results show that the devices have repeatable parameters and are capable of delivering at least 14.4 dB of unilateral gain in S-band with fmax of at least 23 GHz.
PL
W artykule przedstawiono wyniki małosygnałowych pomiarów w.cz. oraz modelowania tranzystorów GaN FET wyprodukowanych w Instytucie Technologii Materiałów Elektronowych (ITME). Badane tranzystory miały bramkę o długości 500 nm i szerokości 100 μm gate i zostały wyprodukowane na podłożu szafirowym o grubości 350 μm. Parametry rozproszenia tranzystorów zostały zmierzone na stacji ostrzowej w pasmie 0,01-15 GHz, a następnie na ich podstawie zostały wyznaczone parametry małosygnałowego schematu zastępczego. Otrzymane wyniki pokazują, że badane tranzystory mają powtarzalne parametry, uzyskując co najmniej 14,4 dB wzmocnienia unilateralnego w pasmie S oraz maksymalną częstotliwość generacji co najmniej 23 GHz.
Przedstawiamy opracowanie przyrządów HEMT (High Electron Mobility Transistors) z GaN/AlGaN, a następnie pierwszego w Polsce monolitycznego mikrofalowego układu scalonego, w którym zastosowano przyrządy HEMT z GaN/AlGaN. Opracowanie przyrządów HEMT. Sekwencja warstw epitaksjalnych tworzących strukturę tranzystora była następująca: bufor AlN, kanał GaN, warstwa Schottky’ego AlGaN oraz warstwa podkontaktowa GaN. Strukturę wyhodowano na podłożu szafirowym. Wzór izolacji oraz wzór obszarów drenów i źródeł uzyskano metodą litografii optycznej. Wzór bramki o długości 500 nm i 440 nm otrzymano metodą bezpośredniej elektronolitografii na powierzchni półprzewodnika. Izolację przyrządów uzyskano przez wytrawienie obszaru ‘mesa’ w plaźmie chlorowej. Metalizacja kontaktów tworzyła struktura wielowarstwowa Ti/Al/Ni/Au. Powierzchnię kanału zabezpieczono przez nałożenie warstwy pasywującej Si3N4. Wzmocnienie tranzystorów w pasmie S i X wynosiło odpowiednio 16 i 11 dB (MSG/MAG Maximum Stable Gain). W najlepszym z kilku opisanych wariantów konstrukcyjnych i technologicznych uzyskano częstotliwość graniczną fT = 30 GHz, częstotliwość graniczną fMAX = 30 GHz. Ponadto stwierdzono, że unilateralne wzmocnienie mocy (UPG) równa się jeden dla częstotliwości ok. 30 GHz. Uzysk wynosił 70% co odpowiada 3000 dobrych przyrządów z płytki o średnicy 2”. Opracowanie mikrofalowego monolitycznego układu scalonego (MMIC).Opracowano pierwszy w Polsce mikrofalowy monolityczny układ scalony (MMIC), klucz typu SPDT (Single Pole Double Throw) stosowany zazwyczaj w układach transciever’ów (klucz nadawanie-odbiór). Układ zbudowany jest z czterech tranzystorów HEMT o szerokości bram μm. W paśmie 0-4 GHz straty wtrącenia są mniejsze niż 2 dB, a izolacja lepsza niż 23 dB. Wykazano, że po zmianie konstrukcji układu i stosując tę samą technologię można uzyskać straty wtrącenia mniejsze niż 1 dB. Przedstawiony układ MMIC jest demonstratorem technologii, przy pomocy której można wykonać układy scalone o parametrach na poziomie komercyjnym.
EN
We present the development of HEMT (High Electron Mobility Transistors) and MMIC (Microwave Monolithic Integrated Circuit) made of GaN/AlGaN. Development of HEMTs. The sequence of epitaxial layers grown on sapphire substrate was as follows: AlN buffer, GaN channel, AlGaN Schottky and GaN contact cap. Isolation pattern and ohmic metal pattern were obtained by optical lithography. The gate was 500 nm and 440 nm long and was written using e-beam directly on semiconductor wafer. Then gate metal was evaporated and lifted off. The isolation was obtained by mesa etching in pure chlorine plasma. Ohmic contact consisted of a Ti/Al/Ni/Au sandwich. Finally Si3N4 passivation was made to protect exposed channel surface. Transistors operate in S and X band, showing 16 and 10 dB MSG/MAG gain respectively. For the best layout design transistors exhibited frequency fT=30 GHz, frequency fMAX = 30 GHz, and exhibited UPG=1 (unilateral power gain) for frequency 30 GHz. The yield was 70%, what corresponds to about 3000 good devices form one 2” wafer. Development of monolithic microwave integrated circuit (MMIC). We developed transistor switch of SPDT (Single Pole Double Throw) type which is used in transceivers. The circuit consists of four HEMT devices having gate width of 150 μm, gate length of 440 nm and drain source distance of 3 μm. In the 0-4 GHz bandwidth insertion loss is less than 2 dB and isolation is better than 23 dB. It was demonstrated that increase of the gate width of transistors will improve insertion loss value to the level of 1 dB.
W chwili obecnej rozwój technologii wytwarzania materiałów półprzewodnikowych i ferrytowych powoduje powstanie nowych możliwości. Zastosowanie nowoczesnych rozwiązań technologicznych przyczynia się do rozwiązania szeregu problemów występujących w konstrukcji dotychczas eksploatowanych urządzeń radiokomunikacyjnych wytwarzających dużą moc, takich jak efektywne odprowadzanie ciepła, większa sprawność, mniejsze gabaryty i masa. W chwili obecnej trendem światowym jest zwiększanie sprawności urządzeń, a tym samym zwiększenie ich użyteczności. W artykule przedstawiona zostanie koncepcja zastosowania ultra szerokopasmowych tranzystorów nowej technologii o większych sprawnościach od dotychczas powszechnie stosowanych. Parametry te zostały potwierdzone eksperymentalnie podczas badań demonstratora wzmacniacza mocy opracowanego na potrzeby systemu rozpoznawczo – zakłócającego. W opracowanym demonstratorze wzmacniacza zastosowane zostały tranzystory posiadające sprawność 35-45%, a uzyskana sprawność całkowita wzmacniacza osiągnęła od 25% do prawie 39%. Uniwersalność opracowanego demonstratora wzmacniacza powoduje, że może on być z powodzeniem zastosowany nie tylko w systemach walki elektronicznych ale również we wszystkich systemach gdzie potrzebne jest wytworzenie dużej mocy w tym również w systemach łączności (KF, UKF, VHF, łączność troposferyczna).
EN
At present, the development of semiconductor manufacturing technology and ferrite materials causes new possibilities. The use of modern technology helps to solve a number of problems which occur in the currently operating radio equipment generating high power, such as effective heat dissipation, higher efficiency, smaller size and weight. This article shows the concept of the use of new technology ultra-broadband transistors with higher efficiencies than the currently widely used. These parameters were confirmed experimentally during the tests of a demonstrator of the power amplifier, which was developed for EW system In the developed demonstrator of amplifier were used transistors with 35-45% efficiency. The resulting total efficiency of the amplifier has reached from 25% to almost 39%. The versatility of this amplifier means that it can be successfully applied in electronic warfare systems and also in all systems where it is necessary to produce high power including the communication systems (HF, VHF, UHF, tropospheric communications).
W artykule przedstawiono wyniki badań wpływu oleju bazowego SN-150 oraz dodatków do olejów smarowych R-2000 (preparat na bazie metali miękkich) i Motor LIFE (preparat o działaniu chemicznym) na strukturę geometryczną powierzchni próbek z żeliwa EN-GJLP-250 po procesie toczenia i nagniatania. Ustalono wpływ oleju bazowego oraz preparatów eksploatacyjnych na parametr chropowatości powierzchni Ra po procesach obróbki. Na podstawie przeprowadzonych badań według metody G. Taguchi i analizy uzyskanych wyników stwierdzono, że preparaty eksploatacyjne nie mają wpływu na strukturę geometryczną powierzchni po obróbce. Dla badanego żeliwa optymalnymi warunkami toczenia i nagniatania powierzchniowego są: minimalne posuwy toczenia i nagniatania, minimalna prędkość toczenia, maksymalne prędkość i siła nagniatania, maksymalny promień naroża noża tokarskiego oraz nagniatanie w obecności oleju bazowego SN-150.
EN
In the article, the results of research on the base machine oil SN 150 and the exploitation additives R-2000 (preparation on the base of soft metals) and Motor LIFE (preparation using chemical actions) influence on the surface geometrical structure of parts from cast iron EN-GJLP-250 when turning and burnishing. The influence of machine oil and exploitation additives on the Ra roughness parameter after machining is defined. On the bases of research using G. Taguchi’s method and the analysed results, the absence of the influence of exploitation additives on the surface geometrical structure after burnishing is explained. The optimal conditions of turning followed by burnishing are defined including the following: minimal feeds of turning and burnishing, minimal speed of turning, maximal speed and force of burnishing, and the maximal nose radius of the cutter in the presence of base machine oil.
W artykule przedstawiono wyniki badań wpływu oleju bazowego SN-150, preparatów eksploatacyjnych do olejów smarowych na bazie metali miękkich (R-2000) oraz o działaniu chemicznym (MotorLIFE) na proces nagniatania żeliwa EN-GJSFP-500-7 oraz na właściwości tribologiczne węzła tarcia przeciwpróbka brąz CuSi3Zn3Mn/próbka nagniatana żeliwo EN-GJSFP-500-7 smarowanego w procesie tarcia olejem bazowym SN-150. Dla celów porównawczych wykonano nagniatanie na sucho. Badania właściwości tribologicznych wykonano za pomocą testera T-05 typu klocek-rolka. Analiza wyników badań potwierdziła pozytywny wpływ preparatu eksploatacyjnego MotorLIFE na właściwości tribologiczne oraz na poprawę parametru chropowatości powierzchni wg Ra dla próbek nagniatanych na sucho i nagniatanych w obecności oleju bazowego SN-150 oraz preparatu eksploatacyjnego R-2000.
EN
In the paper, the results of research on the base machine oil SN-150 and the exploitative preparations R-2000 (preparation on the basis of soft metals) and Motor LIFE (preparation using chemical actions) influence on the tribological properties and stereometric state of cast iron EN-GJSFP-500-7 after a burnishing process. For comparative purposes, dry burnishing was also performed. These investigations were executed on tester T-05 (a roll – the block type tester). The main aim was to establish how the exploitative preparations R-2000 and MotorLIFE influence the surface layer state after the burnishing process. The waste investigations of the burnished surface were realized. Conducted investigations, the obtained results, and their analysis confirm the positive influence of the exploitative preparation MotorLIFE on tribological properties as well as the roughness parameters improvement in relation to the samples of dry burnishing, base machine oil SN-150, and exploitative preparation R-2000.
9
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
Zmętnienie wody Zalewu Wiślanego wskutek wyczerpania z dna gruntów o zawartości cząstek pylasto-gliniastych i organicznych (namułów) przy tworzeniu kanału przez Mierzeję Wiślaną na etapie budowy jak i eksploatacji. Zmiany zasolenia wód w Zalewie Wiślanym występujące jedynie lokalnie i w bardzo niewielkim stopniu. Podstawowe źródło zasolenia wód Zalewu Wiślanego – sztormowe fale od strony Cieśniny Pilawskiej. Naturalne warunki hydrodynamiczne i hydrologiczne wód na Zalewie Wiślanym nie ulegną istotnym zmianom i nadal zależą od warunków hydrometeorologicznych.
EN
Muddy water of the Vistula Lagoon due to exhaustion from the bottom land of the content dusty-clay particles and organic (silt) during creation of the channel through the Vistula Spit at the construction and operation stages. Changes in salinity of the water in the Vistula Lagoon occured only locally and in a very small degree. The primary source of salinity of the Vistula Lagoon – stormy waves of the Strait of Baltiysk. The natural conditions of hydrodynamic and water hydrology on the Vistula Lagoon will not be materially changed and still depend on meteorological and hydrological conditions at sea.
10
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
Przedstawiono wyniki badań, a także rozważania teoretyczne pomocne do bardziej obiektywnego wyznaczania parametrów ruchu pojazdów, które stanowią jeden z wyznaczników doboru metod budowy lub wykonywania prac remontowych warstwy ścieralnej nawierzchni, zapewniających optymalne cechy przyczepności samochodów osobowych, a tym samym zwiększenie bezpieczeństwa w ruchu drogowym.
EN
Presented are the test results as well as theoretical aspects, which might contribute to unbiased estimation of the vehicle movement parameters, which, among others, are usually taken into consideration for selection of the road wearing course building or repair projects for optimum passenger car tractive adhesion and thus, higher traffic safety.
11
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
Podano przykłady modelowania na podstawie ogólnie zorientowanych systemów CFD. Metodykę modelowania za pomocą tych systemów opisano w pracach [1 ÷ 3]. W artykule przedstawiono zagadnienie modelowania przepływu tworzyw w procesie wytłaczania dwuślimakowego przeciwbieżnego. Przedstawiono charakterystykę geometryczną i kinematyczną procesu wytłaczania przeciwbieżnego oraz opisano podstawy przepływu tworzyw, wskazując na całkowitą odmienność tych przepływów w stosunku do wytłaczania jednoślimakowego oraz wytłaczania dwuślimakowego współbieżnego.
EN
Computer aided modeling of plastics molding process. Countercurrent twin screw extrusion. Geometric and kinematic characteristics of the twin screw coutercurrent extrusion process are complemented with explanation of the plastics flow lines as entirely different from those pertaining to the single screw or to the twin screw concurrent flow extrusion.
12
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
Tyres friction traces shapes constitute the basic input parameter for computer simulations of movement reconstruction before and after vehicle collision. Traces often include encoded, possible to readout, information concerning movement dynamics of a car that was marking them. This information may concern also both if the vehicle was intensively braked or not, and what trajectory it was moving before or after arriving the place of collision. In this paper there are presented two selected cases of reconstruction of real road accidents for which issuing of uncompromising opinion and ruling would not be possible without previous identification of tyres traces outlines on the roadway.
13
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
Kinematic features describing the curvilinear track of vehicle make significant problem in analysis of braking, accelerating and also arc driving processes. Recognized features of motion during measurement can be used in analysis of instantaneous values of accelerations, speeds and covered path. Research of the curvilinear track on road generating are oriented for come to know parameters for vehicle movement in given conditions and type of road. In testing grounds were used special measuring device making possible linkage of motion parameters of vehicle with geometrical features formed by track. The paper describes measuring device for three-dimensional canvassing and archiving of motion parameters of vehicle and also presents comparative analysis of the curvilinear contour of track from tyre with vehicle trajectory motion.
In this paper we present results of research on multichannel receiver using Software Defined Radio technology. This receiver is a part of the experimental FM based passive radar being designed. The hardware platform of the receiver consists of the Universal Software Defined Radio Peripheral devices. In the paper we propose modifications of the USRP's FPGA configuration and GNU Radio code. These modifications allow for developing six/nine synchronous input channel receiver based on two/tree USRPs respectively. Issues of synchronization of separate USRP devices by assuring synchronous sampling were presented. We also propose the solution of the problem of the alignment of the data streams being sent from USRP devices via USB to the PC host.
An analysis of the effect of feed foaming on the efficiency of sunflower oil encapsulation on selected product properties is presented in the paper. Experiments were carried out in a pilot-plant concurrent spray dryer using the gas-admixing technique. The analysis of the product properties showed that the application of foaming makes it possible to control final product properties, e.g. apparent density, bulk density, distribution of particle diameters, etc. at a high efficiency of sunflower oil encapsulation.
16
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
Na podstawie badań symulacyjnych i doświadczalnych wytłaczania z dozowanym zasilaniem, z zastosowaniem układu ślimaków ściśle zazębiających się zweryfikowano komputerowy model przepływu tworzywa. Badania prowadzono w warunkach różnych wartości natężenia przepływu tworzywa i różnych prędkości obrotowych ślimaka. Oceniano przebieg uplastyczniania tworzywa i stopień wypełnienia kanału ślimaka, wykonano pomiary ciśnienia tworzywa i momentu obrotowego ślimaka. Uzyskano zadowalającą zgodność wyników pomiarów i obliczeń.
EN
The verification of a computer-derived melt flow model has been performed on the basis of simulation (Figs. 6-10) and experimental studies for a twin-screw closely intermeshing starve feed extrusion (Fig. 1). The tests were carried out under various flow rate and screw rotational speed conditions. The melting process of the polymer and extent of screw chamber filling were also evaluated and pressure and torque measurements carried out. The studies confirm a good agreement between the simulation and experimental results (Figs. 11-13).
17
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
Przedstawiono zagadnienie komputerowego modelowania procesów przetwórstwa tworzyw sztucznych. Podano przykłady modelowania na podstawie ogólnie zorientowanych systemów CFD. W artykule przedstawiono zagadnienie modelowania przepływu tworzyw w procesie wytłaczania jednoślimakowego przy zastosowaniu ślimaków o konstrukcji niekonwencjonalnej.
EN
Presented is problem of the plastics processing computer simulation. Explained are examples of modeling work with reference to the generally oriented CFD systems. A description is given of the plastics flow simulation in the single worm extrusion process with unconventional worm style.
18
Dostęp do pełnego tekstu na zewnętrznej witrynie WWW
The paper presents the comparative analysis of contact roughness between friction surfaces of brake pads, which were fastened to the bicycle frame, and friction surfaces of the element of the wheel rim. The following temporary hypothesis was formulated: on the basis of the measured geometry of the surface irregularities of the elements, it is possible to determine which rim surface cooperated with the left and right brake pad. The proposed method of comparison of the roughness profiles of the frictional braking elements can be useful and appropriate for analyzing some types of vehicle accident reconstructions.
The state-of-the-art is presented for composite modeling of counter-rotating twin screw extrusion of polymeric materials. The closely intermeshing screw configuration is considered. A new approach for composite modeling of counter-rotating twin screw extrusion is discussed. This approach is based on the three dimensional nonNewtonian FEM simulation of flow in an intermeshing modular counter-rotating twin screw extruder. Some experimental and theoretical results of the study are presented. The polymer melting behaviour and degree of filling of the screw channel during the process, as well as the pressure and temperature developments are discussed.
Od kilku lat na świecie trwają badania składników roślin owadożernych wykazujących atrakcyjne właściwości biologicznie czynne, tj. działanie przeciwbakteryjne, przeciwgrzybowe, antyoksydacyjne, a być może, także, przeciwnowotworowe. Pozyskiwanie substancji biologicznie aktywnych z materiału naturalnego, na drodze hodowli in vitro a następnie ekstrakcji i rozdzielania jest bardziej korzystne pod względem ekonomicznym, niż ich wytwarzanie metodami syntezy chemicznej, która w wielu przypadkach składa się z wielu etapów, a wypadkowa efektywności jest często niezadowalajca. W pracy zaprezentowano wyniki badań dotyczących opracowania najkorzystniejszych warunków rozdzielania oraz identyfikacji składników ekstraktów roślin owadożernych z czterech roślin rodziny Droseraceae, tzn., Drosera binata, Drosera capensis, Drosera aliciae oraz Dionea muscipula. Badania polegały na zaprojektowaniu optymalnego układu chromatograficznego oraz optymalnych warunków rozdzielania pozwalających w sposób możliwie jak najbardziej selektywny rozdzielić składniki z grupy naftochinonów oraz flawonoidów. Wykorzystano techniki kolumnowej wysokosprawnej chromatografii cieczowej, w odwróconych układach faz (RPHPLC), Porównano wyniki badań uzyskane z zastosowaniem elucji gradientowej. Za każdym razem stosowano przepływ zwrotny eluentu w kolumnie. Stosowanie elucji gradientowej jest celowe w badaniach składu metabolicznego roślin, identyfikacji oraz oznaczania zawartości składników w ekstraktach, a także w kontroli jakości i standaryzacji materiału zielarskiego.
EN
For several years have been carried out researches of chemical compounds with attractive biological activity (antimicrobial, antifungal, antioxidant and anticancer activity) founded in insectivorous plants. Production of plant metabolites from in vitro cultures by procedures consisting of the extraction methods and separation techniques is economically more advantageous, than classic methods of chemical synthesis, which are consisted of many steps, which final efficiency is unsatisfactory. A developed most favorable conditions for separation and identification of the components of extracts of four plants from Droseraceae: Drosera aliciae, Dionea muscipula, Drosera binata and Drosera capensis are presented in the paper. The optimal conditions of the chromatographic system provide a selective separation of naphthoquinones and flavonoids from the samples of plant extracts. Column chromatography techniques in reversed phase conditions were used in the researches. The paper presents a comparison of separations made in different chromatographic systems with gradient elution. After every separation the direction of the eluent flow in the column was inversed. Application of gradient elution is significant in researches for identification of the compounds and quantitative determination of plant metabolites, as well as for the quality control and standardization of natural herbal materials
JavaScript jest wyłączony w Twojej przeglądarce internetowej. Włącz go, a następnie odśwież stronę, aby móc w pełni z niej korzystać.