Laboratory Tests and Numerical Simulations of Two Anti-Vibration Structures Made by 3D Printing – Comparative Research

• Autorzy: Kowalski Piotr , Alikowski Adrian

Identyfikatory

DOI

10.24425/aoa.2023.146642

• Języki publikacji: EN

Abstrakty

EN

This article presents a comparison of test results from two models of anti-vibration systems (I and II) made employing MJF 3D printing technology and two different materials. The research included laboratory tests and numerical simulations, assuming a linear nature of the mechanical properties for the materials and models of structures. The aim of this research was to assess the consistency between laboratory test and numerical simulation results. In addition, evaluation of the suitability of using MJF technology to produce antivibration systems was conducted. During the laboratory tests, the response of the two models of structures to vibrations generated by an exciter was recorded using a high-speed camera. Subsequent image analysis was performed using the MOVIAS Neo software. The obtained values of vibration displacements and resonant frequencies were used to validate the numerical model created in the Simcenter Femap software. Relative differences between the values of resonant frequencies obtained experimentally and through simulations were determined. In the case of the structural model I, creating its numerical model without considering the nonlinearity of mechanical parameters was found to be unjustified. The comparison of the displacements determined during numerical simulations showed relative differences of less than 16% for both models in relation to the laboratory test results. This comparison result indicates a satisfactory accuracy in simulating this parameter. An assessment of the quality and accuracy of MJF technology-produced prints, led to the conclusion that due to the formation of internal stresses during the print creation, the use of “soft” materials in this technology is problematic.

Słowa kluczowe

EN

finite element method; 3D printing; mechanical vibrations

• Wydawca: Instytut Podstawowych Problemów Techniki PAN ; Komitet Akustyki PAN ; Polskie Towarzystwo Akustyczne
• Czasopismo: Archives of Acoustics
• Rocznik: 2023
• Tom: Vol. 48, No. 4
• Strony: 523–--527
• Opis fizyczny: Bibliogr. 12 poz., fot., rys., tab.

Twórcy

autor

Kowalski Piotr

• Central Institute for Labour Protection – National Research Institute Poland

• https://orcid.org/0000-0003-4066-9967

autor

Alikowski Adrian

• Central Institute for Labour Protection – National Research Institute Poland

• https://orcid.org/0000-0003-1147-2516

Bibliografia

• 1. Abbot D.W., Kallon D.V.V., Anghel C., Dube P. (2019), Finite element analysis of 3D printed model via compression tests, Procedia Manufacturing, 35: 164-173, doi: 10.1016/j.promfg.2019.06.001.
• 2. Burlayenko V.N., Sadowski T., Altenbach H., Dimitrova S. (2019), Three-dimensional finite element modelling of free vibrations of functionally graded sandwich panels, [in:] Recent Developments in the Theory of Shells, Altenbach H., Chróscielewski J., Eremeyev V., Wisniewski K. [Eds], pp. 157-177, Springer.
• 3. David Müzel S., Bonhin E.P., Guimarães N.M., Guidi E.S. (2020), Application of the finite element method in the analysis of composite materials: A review, Polymers, 12(4): 818, doi: 10.3390/polym12040818.
• 4. Jindal P., Worcester F., Siena F.L., Forbes C., Juneja M., Breedon P. (2020), Mechanical behaviour of 3D printed vs thermoformed clear dental aligner materials under non-linear compressive loading sing FEM, Journal of the Mechanical Behavior of Biomedical Materials, 112: 104045, doi: 10.1016/j.jmbbm.2020.104045.
• 5. Kamel M.A., Ibrahim K., El-Makarem Ahmed A. (2019), Vibration control of smart cantilever beam using finite element method, Alexandria Engineering Journal, 58(2): 591-601, doi: 10.1016/j.aej.2019.05.009.
• 6. Park J.H., Lee J.R. (2019), Developing fall-impact protection pad with 3D mesh curved surface structure using 3D printing technology, Polymers, 11(11): 1800, doi: 10.3390/polym11111800.
• 7. Sari B., Kazemi Lichaei M., Yildirim S. (2022), Free vibration analysis of tapered composite aircraft wing via the finite element method, Cukurova University Journal of the Faculty of Engineering, 37(3): 741-752, doi: 10.21605/cukurovaumfd.1190386.
• 8. Sathyapriya G. et al. (2022), Development of compliant vibration isolation damper and its performance analysis in turning operation, Advances in Materials Science and Engineering, 2022: 6860178, doi: 10.1155/2022/6860178.
• 9. Shi Y., Lee R.Y.Y., Mei C. (1997), Finite element method for nonlinear free vibrations of composite plates, AIAA Journal, 35(1): 159-166, doi: 10.2514/2.78.
• 10. Yang Y., Chen Y., Wei Y., Li Y. (2016), 3D printing of shape memory polymer for functional part fabrication, The International Journal of Advanced Manufacturing Technology, 84(9): 2079-2095, doi: 10.1007/s00170-015-7843-2.
• 11. Zolfagharian A., Bodaghi M., Hamzehei R., Parr L., Fard M., Rolfe B.F. (2022), 3D-printed programmable mechanical metamaterials for vibration isolation and buckling control, Sustainability, 14(11): 6831, doi: 10.3390/su14116831.
• 12. Zur P., Kołodziej A., Baier A. (2019), Finite elements analysis of PLA 3D-printed elements and shape optimization, European Journal of Engineering Science and Technology, 2(1): 59-64, doi: 10.33422/EJEST.2019.01.51.

Uwagi

Opracowanie rekordu ze środków MNiSW, umowa nr SONP/SP/546092/2022 w ramach programu "Społeczna odpowiedzialność nauki" - moduł: Popularyzacja nauki i promocja sportu (2024).