The replication method to analyze roughness of shaft, tool, and grinding wheel microgeometry

• Autorzy: Szawara Paulina , Ostrowski Robert

Identyfikatory

DOI

10.2478/amst-2019-0022

• Języki publikacji: EN

Abstrakty

EN

This article presents the possibility of using the replication method to measure selected parameters of the surface geometry. The results of the tests obtained while measuring the replica and surface of the tested object are presented. The obtained results indicate the suitability of using RepliSet F5 to measure the roughness parameters (Ra and Rz), microgeometry tool, and grinding wheel. It has been proven that the replication method using the RepliSet F5 is suitable for chosen parameters of roughness and tool microgeometry measurements. However, it is not suitable for measuring the porosity of a grinding wheel.

Słowa kluczowe

EN

replica; geometric structure of surface; replication method; RepliSet F5

PL

replika; struktura geometryczna powierzchni; metoda replikacji; RepliSet F5

• Wydawca: Komitet Budowy Maszyn PAN ; De Gruyter
• Czasopismo: Advances in Manufacturing Science and Technology
• Rocznik: 2020
• Tom: Vol. 44, nr 4
• Strony: 129--133
• Opis fizyczny: Bibliogr. 10 poz., rys., tab., wykr.

Twórcy

autor

Szawara Paulina

• Depth of Materials Forming and Processing, The Faculty of Mechanical Engineering and Aeronautics, Rzeszów University of Technology, Al. Powstańców Warszawy 8, 35-329 Rzeszów

autor

Ostrowski Robert

• Depth of Materials Forming and Processing, The Faculty of Mechanical Engineering and Aeronautics, Rzeszów University of Technology, Al. Powstańców Warszawy 8, 35-329 Rzeszów

Bibliografia

• [1] T.M. Smith: Dental histology. In (Richards, M., Britton, K., Eds.) Archaeological science: An introduction. Cambridge University Press, New York 2019, 170-197.
• [2] D. Guatelli-Steinberg, J.C. Mitchell: RepliSet: High resolution impressions of the teeth of human ancestors. Structure: Struers J. Materialogr., 40(2003), 9-12.
• [3] T.M. Smith., D.J. Reid: Temporal nature of periradicual bands (‘Striae Periradicales’) on mammalian tooths roots, 14th International Symposium on Dental Morphology, Greifswald, August 2008: Selected Papers.
• [4] J. Newman, et al.: Replica-based crack inspection. Eng. Fract. Mech., 76(2009)7, 898-910.
• [5] E. Altintas, E. Güngör: Alternative surface roughness measurement technique for inaccessible surfaces of jet engine parts using the rubber silicon replica method. Metall. Microstruct Anal., 2(2013), 337-342. Springer Science.
• [6] W. Kacalak, K. Tandecka, D. Lipiński: Analysis of the accuracy of the assessment of the consumption of the active Surface of abrasive tools using RepliSet replicas in the system and spatial scanning in industrial environments. Mechanik, 8-9(2015).
• [7] A. Guzanová, D. Draganovská, J. Brezinová: Non-destructive surface diagnostics of tools. Mater Sci Forum, 818(2015), 41-44.
• [8] J.K. Thompson, et al: Novel methodology to quantify tool wear in powder metallurgy. Proc. 2007 Inter. Conf. Powder Metallurgy & Particulate Materials (PowderMet 2007).
• [9] T. Naoe, et al: Cavitation damage in double-walled mercury target vessel. J. Nucl. Mater., 506(2018), 35–42.
• [10] E. Syverud, O. Brekke, L.E. Bakken: Axial compressor deterioration caused by saltwater ingestion. Proc GT2005, ASME Turbo Expo, Reno-Tahoe, Nevada, USA 2005, 1-11.

Uwagi

Opracowanie rekordu ze środków MNiSW, umowa Nr 461252 w ramach programu "Społeczna odpowiedzialność nauki" - moduł: Popularyzacja nauki i promocja sportu (2021).