3D DIC-assisted residual stress measurement in 316 LVM steel processed by HE and HPT

• Autorzy: Brynk Tomasz , Krawczyńska Agnieszka Teresa , Setman Daria , Pakieła Zbigniew

Identyfikatory

DOI

10.1007/s43452-020-00068-4

• Języki publikacji: EN

Abstrakty

EN

A method has been developed for determining residual stress based on displacement fields near drilled holes analyzed using 3D digital image correlation. Finite element modeling was used to determine corrections for analytical equations describing displacement fields near the blind holes, which made it possible to determine the residual stress distribution over a wide range of hole depth-to-hole diameter ratios and various areas of displacement field measurements using inverse method iterative calculations. The proposed method eliminates many drawbacks of traditional procedure based on strain gauges as hole eccentricity sensitivity and requirement of the relatively large span between holes. The method and testing setup, build-up of generally available components, were used to determine the residual stress distribution for 316 LVM samples processed by two methods from the large deformation group: hydrostatic extrusion (HE) and high-pressure torsion (HPT), by drilling 1.75 and 0.58-mm-diameter blind holes, respectively. In the case of the measurements performed on the surface of a HE-processed 16 mm bar cut along its diameter, a gradual change was revealed-from a compressive to a tensile residual stress distribution (from ~ − 300 MPa in the center to 400 MPa in 4 mm distance from the edge) in the longitudinal direction, with near-zero values in the radial direction. Moreover, the method was also adapted to perform measurements on the outside surface of the bar, which gave results consistent with those taken along the radius profile (~ 600 MPa longitudinal stress). Measurements on the top surface of a cylinder 10 mm in diameter and 1 mm high processed by HPT showed a high compressive residual stress in the center and a dominant shear component for the holes drilled at different distances from the center.

Słowa kluczowe

EN

residual stress; 3D digital image correlation; hydrostatic extrusion; high-pressure torsion; severe plastic deformation; austenitic steel

PL

naprężenie; wytłaczanie hydrostatyczne; skręcanie; odkształcenie plastyczne; stal austenityczna

• Wydawca: Springer ; Wrocław University of Science and Technology
• Czasopismo: Archives of Civil and Mechanical Engineering
• Rocznik: 2020
• Tom: Vol. 20, no. 3
• Strony: 18--29
• Opis fizyczny: Bibliogr. 36 poz., fot., wykr.

Twórcy

autor

Brynk Tomasz

• Faculty of Materials Science and Engineering, Warsaw University of Technology, Woloska 141, 02‑507 Warsaw, Poland

autor

Krawczyńska Agnieszka Teresa

• Faculty of Materials Science and Engineering, Warsaw University of Technology, Woloska 141, 02‑507 Warsaw, Poland

autor

Setman Daria

• Faculty of Physics, University of Vienna, Boltzmanngasse 5, 1090 Vienna, Austria

autor

Pakieła Zbigniew

• Faculty of Materials Science and Engineering, Warsaw University of Technology, Woloska 141, 02‑507 Warsaw, Poland

Bibliografia

• [1] Rossini NS, Dassisti M, Benyounis KY, Olabi AG. Methods of measuring residual stresses in components. Mater Des. 2012. https ://doi.org/10.1016/j.matde s.2011.08.022.
• [2] Lowe TC, Valiev RZ. The use of severe plastic deformation techniques in grain refinement. JOM. 2004. https ://doi.org/10.1007/s1183 7-004-0295-z.
• [3] Valiev RZ, Estrin Y, Horita Z, Langdon TG, Zehetbauer MJ, Zhu YT. Producing bulk ultrafine-grained materials by severe plastic deformation. JOM. 2006. https ://doi.org/10.1007/s11837-006-0213-7.
• [4] Valiev RZ, Korznikov AV, Mulyukov RR. Structure and properties of ultrafine-grained materials produced by severe plastic deformation. Mater Sci Eng A. 1993. https ://doi.org/10.1016/0921-5093(93)90717 -S.
• [5] Valiev RZ, Islamgaliev RK, Alexandrov IV. Bulk nanostructured materials from severe plastic deformation. Prog Mater Sci. 2000.https ://doi.org/10.1016/S0079 -6425(99)00007 -9.
• [6] Pakieła Z, Garbacz H, Lewandowska M, Druzycka-Wiencek A, Suś-Ryszkowska M, Zieliński W, Kurzydłowski KJ. Structure and properties of nanomaterials produced by severe plastic deformation. Nukleonika. 2006;51:S19–25.
• [7] Sedighi M, Mahmoodi M. Residual stresses evaluation in equal channel angular rolled al 5083 by IHD technique: investigation of two calculation methods. Mater Manuf Process. 2013. https ://doi.org/10.1080/10426 914.2012.70014 9.
• [8] Zdunek J, Maj P, Kulczyk M, Mizera J. Texture, residual stresses and mechanical properties analysis in the commercial 1.4462 duplex stainless steel subjected to hydrostatic extrusion. Arch Civ Mech Eng. 2019. https ://doi.org/10.1016/j.acme.2018.12.008.
• [9] Lee HH, Gangwar KD, Park KT, Woo W, Kim HS. Neutron diffraction and finite element analysis of the residual stress distribution of copper processed by equal-channel angular pressing. Mater Sci Eng A. 2017. https ://doi.org/10.1016/j.msea.2016.11.094.
• [10] Geist D, Rentenberger C, Karnthaler HP. Extreme structural inhomogeneities in high-pressure torsion samples along the axial direction. Acta Mater. 2011. https ://doi.org/10.1016/j.actamat.2011.04.003.
• [11] Todt J, Keckes J, Winter G, Staron P, Hohenwarter A. Gradient residual strain and stress distributions in a high pressure torsion deformed iron disk revealed by high energy X-ray diffraction. Scr Mater. 2018. https ://doi.org/10.1016/j.scrip tamat .2017.11.037.
• [12] Korznikov AV, Pakieła Z, Kurzydłowski KJ. Influence of longrange ordering on mechanical properties of nanocrystalline Ni3Al. Scr Mater. 2001. https ://doi.org/10.1016/S1359 -6462(01)01033 -8.
• [13] Mathar J. Determination of initial stresses by measuring the deformation around drilled holes. Trans ASME. 1934;56:249–54.
• [14] ASTM E837-13a. Standard test method for determining residual stresses by the hole-drilling strain-gage method. Stand. Test Method E837-13a; 2013. https ://doi.org/10.1520/e0837 -13a.
• [15] Helm JD. Improved three-dimensional image correlation for surface displacement measurement. Opt Eng. 1996;35:1911. https ://doi.org/10.1117/1.60062 4.
• [16] Huang X, Liu Z, Xie H. Recent progress in residual stress measurement techniques. Acta Mech Solida Sin. 2013. https ://doi.org/10.1016/S0894 -9166(14)60002 -1.
• [17] Hagara M, Trebuňa F, Pástor M, Huňady R, Lengvarský P. Analysis of the aspects of residual stresses quantification performed by 3D DIC combined with standardized hole-drilling method. Meas J Int Meas Confed. 2019. https ://doi.org/10.1016/j.measu rement.2019.01.028.
• [18] Valiev RZ, Parfenov EV, Raab GI, Semenova IP, Dluhoš L. Bulk nanostructured metals for advanced medical implants and devices. IOP Conf Ser Mater Sci Eng. 2018. https ://doi.org/10.1088/1757-899x/461/1/01208 9.
• [19] Pachla W, Skiba J, Kulczyk M, Przybysz S, Przybysz M, Wróblewska M, Diduszko R, Stepniak R, Bajorek J, Radomski M, Fafara W. Nanostructurization of 316L type austenitic stainless steels by hydrostatic extrusion. Mater Sci Eng A. 2014. https ://doi.org/10.1016/j.msea.2014.07.069.
• [20] Guo J, Fu H, Pan B, Kang R. Recent progress of residual stress measurement methods: a review. Chin J Aeronaut. 2019. https ://doi.org/10.1016/j.cja.2019.10.010.
• [21] Giri A, Pandey C, Mahapatra MM, Sharma K, Singh PK. On the estimation of error in measuring the residual stress by strain gauge rosette. Meas J Int Meas Confed. 2015. https ://doi.org/10.1016/j.measu remen t.2014.12.047.
• [22] Giri A, Pandey C, Mahapatra M. To study the effect of stress magnitude and tool geometry on the calibration coefficients: ring core technique. Proc Inst Mech Eng Part E J Process Mech Eng. 2017;232:095440891773758. https ://doi.org/10.1177/09544 0891773758 5.
• [23] Nelson DV, Makino A, Schmidt T. Residual stress determination using hole drilling and 3D image correlation. Exp Mech. 2006. https ://doi.org/10.1007/s1134 0-006-5859-0.
• [24] Kurzydlowski KJ. Hydrostatic extrusion as a method of grain refinement in metallic materials. Mater Sci Forum. 2006. https ://doi.org/10.4028/www.scien tific .net/msf.503-504.341.
• [25] Edalati K, Horita Z. A review on high-pressure torsion (HPT) from 1935 to 1988. Mater Sci Eng A. 2016. https ://doi.org/10.1016/j.msea.2015.11.074.
• [26] Krawczynska AT, Chrominski W, Ura-Binczyk E, Kulczyk M, Lewandowska M. Mechanical properties and corrosion resistance of ultrafine grained austenitic stainless steel processed by hydrostatic extrusion. Mater Des. 2017. https ://doi.org/10.1016/j.matdes.2017.09.050.
• [27] Krawczynska AT, Gierlotka S, Suchecki P, Setman D, Adamczyk-Cieslak B, Lewandowska M, Zehetbauer M. Recrystallization and grain growth of a nano/ultrafine structured austenitic stainless steel during annealing under high hydrostatic pressure. J Mater Sci. 2018. https ://doi.org/10.1007/s1085 3-018-2459-1.
• [28] Brynk T. Development and validation of 3D DIC based residual stress testing method; 2019. p. 65–70. https ://doi.org/10.1007/978-3-030-21894 -2_13.
• [29] Brynk T, Romelczyk-Baishya B. Residual stress estimation based on 3D DIC displacement filed measurement around drilled holes. Procedia Struct Integr. 2018;13:1267–72. https ://doi.org/10.1016/j.prost r.2018.12.259.
• [30] Lord JD, Penn D, Whitehead P. The application of digital image correlation for measuring residual stress by incremental hole drilling. Appl Mech Mater. 2008. https ://doi.org/10.4028/www.scientific .net/AMM.13-14.65.
• [31] Makino A, Nelson D. Residual-stress determination by single-axis holographic interferometry and hole drilling-part I: theory. Exp Mech. 1994. https ://doi.org/10.1007/BF023 28443.
• [32] Yoneyama S, Ogawa T, Kobayashi Y. Evaluating mixed-mode stress intensity factors from full-field displacement fields obtained by optical methods. Eng Fract Mech. 2007. https ://doi.org/10.1016/j.engfr acmec h.2006.08.004.
• [33] Brynk T, Laptiev A, Tolochyn O, Pakiela Z. The method of fracture toughness measurement of brittle materials by means of high speed camera and DIC. Comput Mater Sci. 2012;64:221–4. https ://doi.org/10.1016/j.comma tsci.2012.05.025.
• [34] Totten G, Howes M, Inoue T, editors. Handbook of residual stress and deformation of steel. Materials Park: ASM International; 2002.
• [35] Zhan K, Jiang CH, Ji V. Uniformity of residual stress distribution on the surface of S30432 austenitic stainless steel by different shot peening processes. Mater Lett. 2013. https ://doi.org/10.1016/j.matle t.2012.08.147.
• [36] Ye C, Telang A, Gill AS, Suslov S, Idell Y, Zweiacker K, Wiezorek JMK, Zhou Z, Qian D, Mannava SR, Vasudevan VK. Gradient nanostructure and residual stresses induced by ultrasonic nano-crystal surface modification in 304 austenitic stainless steel for high strength and high ductility. Mater Sci Eng A. 2014. https://doi.org/10.1016/j.msea.2014.06.114.

Uwagi

PL

Opracowanie rekordu ze środków MNiSW, umowa Nr 461252 w ramach programu "Społeczna odpowiedzialność nauki" - moduł: Popularyzacja nauki i promocja sportu (2021)