Wpływ infiltracji próżniowej na właściwości mechaniczne polimerobetonów wzmacnianych lekkimi kruszywami ceramicznymi

Smoleń, Jakub; Pawlik, Tomasz

doi:10.32047/CWB.2023.28.1.5

Artykuł - szczegóły

Tytuł artykułu

Wpływ infiltracji próżniowej na właściwości mechaniczne polimerobetonów wzmacnianych lekkimi kruszywami ceramicznymi

Autorzy

Smoleń Jakub , Pawlik Tomasz

Wybrane pełne teksty z tego czasopisma

http://www.cementwapnobeton.pl/

Identyfikatory

DOI

10.32047/CWB.2023.28.1.5

Warianty tytułu

Influence of vacuum infiltration on mechanical properties of polymer concrete filled with lightweight ceramic aggregates

Języki publikacji

PL EN

Abstrakty

W niniejszej pracy opisano wpływ inflitracji próżniowej na właściwości polimerobetonów na bazie lekkich agregatów ceramicznych. W pierwszym etapie badań wytworzono ceramiczne granule o wysokiej porowatości otwartej, około 27%, w oparciu o wykorzystanie przemysłowych materiałów odpadowych. Ceramiczne agregaty, zwane dalej granulatami, o wielkości od 2 do 4 mm wytworzono z wykorzystaniem zanieczyszczonej stłuczki szklanej oraz łupków węglowych. Omówiono efektywność infiltracji granulatu żywicą epoksydową w produkcji polimerobetonu o wysokiej wytrzymałości mechanicznej i stosunkowo małej masie w porównaniu z tradycyjnym betonem. Wytrzymałość na ściskanie polimerobetonu w którym kruszywo infiltrowano próżniowo żywicą wynosi 87 MPa, a polimerobetonu w którym zastosowano infiltrację zanurzeniową wytrzymałość na ściskanie wynosi około 42 MPa. Powstały polimerobeton, ze względu na swoją gęstość, zaliczany jest do betonów lekkich o wysokiej wytrzymałości.

In this paper, the influence of vacuum infiltration of lightweight ceramic aggregates as fillers in polymeric concretes was described. In the first stage of the investigation, a set of ceramic aggregates with a high open porosity of about 27% was produced on the basis of industrial wastes. Ceramic aggregates with a size of 2 to 4 mm, hereinafter referred to as granules, were produced using contaminated glass cullet waste and coal shale. The effectiveness of granule infiltration with epoxy resin in the production of polymer concrete with high mechanical strength and relatively low mass compared to traditional concrete was discussed. The compressive strength of polymer concrete, where the aggregates were infiltrated with resin, is 87 MPa, and the polymer concrete, in which the vacuum infiltration process was not used, reaches a compressive strength of approximately 42 MPa. The resulting concrete, due to its density, is classified as a lightweight high-strength concrete.

Słowa kluczowe

polimerobeton kompozyt recyklizacja kruszywo lekkie kruszywo ceramiczne infiltracja próżniowa właściwości mechaniczne

polymer concrete composite recycling lightweight aggregate ceramic aggregate vacuum infiltration mechanical properties

Wydawca

Fundacja Cement, Wapno, Beton

Czasopismo

Cement Wapno Beton

Rocznik

2023

Tom

R. 28, nr 1

Strony

56--64

Opis fizyczny

Bibliogr. 36 poz., il., tab.

Twórcy

autor

Smoleń Jakub

jakub.smolen@polsl.pl

Faculty of Materials Science, Silesian University of Technology, Katowice, Poland

autor

Pawlik Tomasz

Faculty of Materials Science, Silesian University of Technology, Katowice, Poland

Bibliografia

1. V. Choudhry, S. R. Hadley, Utilization of Coal Gasification Slag. ACS Symp. Ser. 515, 253-263 (1992). https://doi.org/10.1021/bk-1992-0515.ch020
2. V. Sata, P. Chindaprasirt, Use of construction and demolition waste (CDW) for alkali-activated or geopolymer concrete. Adv. Constr. Demol. Waste Recycl. 385-403 (2020). https://doi.org/10.1016/b978-0-12-819055-5.00019-X
3. H.J. Chen, M.D. Yang, C.W. Tang, S.Y. Wang, Producing synthetic lightweight aggregates from reservoir sediments. Constr. Build. Mater. 28(1), 387-394 (2012). https://doi.org/10.1016/j.conbuildmat.2011.08.051
4. M. Liu, C. Wang, Y. Bai, G. Xu, Effects of sintering temperature on the characteristics of lightweight aggregate made from sewage sludge and river sediment. J. Alloys Compd. 748, 522-527 (2018). https://doi.org/10.1016/j.jallcom.2018.03.216
5. J. M. Moreno-Maroto, M. Uceda-Rodríguez, C. J. Cobo-Ceacero, T. Cotes-Palomino, C. Martínez-García, J. Alonso-Azcárate, Studying the feasibility of a selection of Southern European ceramic clays for the production of lightweight aggregates. Constr. Build. Mater. 237, 117583 (2020). https://doi.org/10.1016/j.conbuildmat.2019.117583
6. A. A. Boateng, E. R. Thoen, F. L. Orthlieb, Modelling the pyroprocess kinetics of shale expansion in a rotary kiln. Chem. Eng. Res. Des. 75(3), 278-283 (1997). https://doi.org/10.1205/026387697523723
7. W. Szczygielski, I. Walentek, Surowce ceramiki budowlanej (building ceramics raw materials), surowce do produkcji kruszyw ceramicznych i cementu (mineral raw materials for production of clay aggregates and cement clinker). In: „Bilans perspektywicznych zasobów kopalin Polski wg stanu na 31.12.2018 r.” (K. Szamałek, M. Szuflicki, W. Mizerski), 239-257 (2020). PIG-PIB, Warszawa.
8. H. J. Chen., S. Y. Wang, C. W. Tang, Reuse of incineration fly ashes and reaction ashes for manufacturing lightweight aggregate. Constr. Build. Mater. 24(1), 46-55 (2010). https://doi.org/10.1016/j.conbuildmat.2009.08.008
9. O. Kayali, Fly ash lightweight aggregates in high performance concrete. Constr. Build. Mater. 22(12), 2393-2399 (2008). https://doi.org/10.1016/j.conbuildmat.2007.09.001
10. J. M. J. M. Bijen, Manufacturing processes of artificial lightweight aggregates from fly ash. Int. J. Cem. Comp. Lightweight Concr. 8(3), 191-199 (1986). https://doi.org/10.1016/0262-5075(86)90040-0
11. J. Chiou, K. S. Wang, C. H. Chen, Y. T. Lin, Lightweight aggregate made from sewage sludge and incinerated ash. Waste Manag. 26(12), 1453-1461 (2006). https://doi.org/10.1016/j.wasman.2005.11.024
12. M. Franus, D. Barnat-Hunek, M. Wdowin, Utilization of sewage sludge in the manufacture of lightweight aggregate. Environ. Monit. Assess. 188(1), 1-13 (2016). https://doi.org/10.1007/s10661-015-5010-8
13. M. Liu, C. Wang, Y. Bai, G. Xu, Effects of sintering temperature on the characteristics of lightweight aggregate made from sewage sludge and river sediment. J. Alloys Compd. 748, 522-527 (2018). https://doi.org/10.1016/j.jallcom.2018.03.216
14. B. L. A. Tuan, C. L. Hwang, K. L. Lin, Y. Y. Chen, M. P. Young, Development of lightweight aggregate from sewage sludge and waste glass powder for concrete. Constr. Build. Mater. 47, 334-339 (2013). https://doi.org/10.1016/j.conbuildmat.2013.05.039
15. I. Kourti, C. R. Cheeseman, Properties and microstructure of lightweight aggregate produced from lignite coal fly ash and recycled glass. Resour. Conserv. Recyc. 54(11), 769-775 (2010). https://doi.org/10.1016/j.resconrec.2009.12.006
16. F. Andreola, A. Borghi, S. Pedrazzi, G. Allesina, P. Tartarini, I. Lancellotti, L. Barbieri, Spent coffee grounds in the production of lightweight clay ceramic aggregates in view of urban and agricultural sustainable development. Materials, 12(21), 3581 (2019). https://doi.org/10.3390/ma12213581
17. G. P. Lyra, V. dos Santos, B. C. De Santis, R. R. Rivaben, C. Fischer, E. M. D. J. A. Pallone, J. A. Rossignolo, Reuse of sugarcane bagasse ash to produce a lightweight aggregate using microwave oven sintering. Constr. Build. Mater. 222, 222-228 (2019). https://doi.org/10.1016/j.conbuildmat.2019.06.150
18. T. Y. Lo, W. C. Tang, H.Z. Cui, The effects of aggregate properties on lightweight concrete. Build. Environ. 42(8), 3025-3029 (2007). https://doi.org/10.1016/j.buildenv.2005.06.031
19. A. Terzić, L. Pezo, V. Mitić, Z. Radojević, Artificial fly ash based aggregates properties influence on lightweight concrete performances. Ceram. Int. 41(2), 2714-2726 (2015). https://doi.org/10.1016/j.ceramint.2014.10.086
20. S. T. Tassew, A. S. Lubell, Mechanical properties of lightweight ceramic concrete. Mater. Struct. 45(4), 561-574 (2012). https://doi.org/10.1617/s11527-011-9782-1
21. A. M. Rashad, Lightweight expanded clay aggregate as a building material - An overview. Constr. Build. Mater. 170, 757-775 (2018). doi:10.1016/j.conbuildmat.2018.03.009
22. D. Jóźwiak-Niedźwiedzka, Scaling resistance of high performance concretes containing a small portion of pre-wetted lightweight fine aggregate. Cem. Concr. Comp. 27(6), 709-715 (2005). https://doi.org/10.1016/j.cemconcomp.2004.11.001
23. H. K. Kim, J. H. Jeon, H. K. Lee, Workability, and mechanical, acoustic and thermal properties of lightweight aggregate concrete with a high volume of entrained air. Constr. Build. Mater. 29, 193-200 (2012). https://doi.org/10.1016/j.conbuildmat.2011.08.067
24. M. C . Nepomuceno, L. A. Pereira-de-Oliveira, S. F. Pereira, Mix design of structural lightweight self-compacting concrete incorporating coarse lightweight expanded clay aggregates. Constr. Build. Mater. 166, 373-385 (2018). https://doi.org/10.1016/j.conbuildmat.2018.01.161
25. N. Salem, M. Ltifi, H. Hassis, Characterization of lightweight aggregates manufactured from Tunisian clay. J. Sci. Res. 4(7), 43-51 (2014).
26. M. Malešev, V. Radonjanin, I. Lukić, V. Bulatović, The effect of aggregate, type and quantity of cement on modulus of elasticity of lightweight aggregate concrete. Arabian J. Sci. Eng. 39(2), 705-711 (2014). https://doi.org/10.1007/s13369-013-0702-2
27. J. Alexandre Bogas, M. G. Gomes, S. Real, Capillary absorption of structural lightweight aggregate concrete. Mater. Struct. 48(9), 2869-2883 (2015). https://doi.org/10.1617/s11527-014-0364-x
28. L. Bodnárová, R. Hela, M. Hubertová, I. Nováková, Behaviour of lightweight expanded clay aggregate concrete exposed to high temperatures. Int. J. Civil Environ. Eng. 8(12), 1210-1213 (2014).
29. L. Czarnecki, Betony polimerowe. Cement Wapno Beton, 2, 63-82 (2010).
30. M. Nodehi, Epoxy, polyester and vinyl ester based polymer concrete: a review. Innovative Infrastructure Solutions, 7(1), 1-24 (2022). https://doi.org/10.1007/s41062-021-00661-3
31. J. Zeschky, J. Lo, T. Höfner, P. Greil, Mg alloy infiltrated Si-O-C ceramic foams. Materials Science and Engineering: A, 403(1-2), 215-221 (2005). https://doi.org/10.1016/j.msea.2005.04.052
32. S. Vaucher, J. Kuebler, O. Beffort, L. Biasetto, F. Zordan, P. Colombo, Ceramic foam-reinforced Al-based micro-composites. Comp. Sci. Techn. 68(15-16), 3202-3207 (2008). https://doi.org/10.1016/j.compscitech.2008.08.004
33. P. Colombo, F. Zordan, E. Medvedovski, Ceramic-polymer composites for ballistic protection. Adv. Appl. Ceram. 105(2), 78-83 (2006). https://doi.org/10.1179/174367606X84440
34. A. Olszówka-Myalska, M. Godzierz, J. Myalski, Impact of carbon foam cell sizes on the microstructure and properties of pressure infiltrated magnesium matrix composites. Materials, 13(24), 5619 (2020). https://doi.org/10.3390/ma13245619
35. J.G. de Salazar, M.I. Barrena, G. Morales, L. Matesanz, N. Merino, Compression strength and wear resistance of ceramic foams-polymer composites. Mater. Lett. 60(13-14), 1687-1692 (2006). https://doi.org/10.1016/j.matlet.2005.11.092
36. M. Godzierz, B. Adamczyk, T. Pawlik, M. Sopicka-Lizer, Mechanical and physical properties of light-weight ceramic aggregates prepared from waste materials. Waste Biomass Valor. 11(5), 2309-2319 (2020). https://doi.org/10.1007/s12649-018-0464-x

Typ dokumentu

Bibliografia

Identyfikator YADDA

bwmeta1.element.baztech-ed859329-eb98-420d-a575-6cee64daf4e0