Experimental Investigation of Cutting Forces in High-Feed Milling of Titanium Alloy

• Autorzy: Petrů Jana , Drábek Lukáš , Hajnyš Jiří , Jurok Dalibor , Pagáč Marek , Měsíček Jakub

Identyfikatory

DOI

10.12913/22998624/113615

• Języki publikacji: EN

Abstrakty

EN

Titanium super alloys are often used in the chemical and aerospace industries, especially because of financial savings, resulting primarily from cheaper operation of equipment. Machinability of titanium alloys is more difficult than that of other metals. In addition, the low thermal conductivity causes the alloy to stick to the cutting edge of the cutting tool, thereby causing it to become dull faster. The article deals with the experimental evaluation of cutting forces and the design of suitable cutting parameters for the machining of the UNS R56260 titanium alloy with high-feed milling technology. Testing was carried out in climb and conventional milling under different cutting conditions. The cutting components of forces Fx, Fy, Fz were measured and evaluated. The results of the measurements were processed into a graphical form and suitable cutting conditions were designed in terms of the acting cutting forces.

Słowa kluczowe

EN

high-feed milling; titanium alloy; cutting forces

PL

frezowanie z dużymi posuwami; stop tytanu; siły skrawania

• Wydawca: Lublin University of Technology ; Polish Society of Ecological Engineering (PTIE), Branch of PTIE in Lublin
• Czasopismo: Advances in Science and Technology. Research Journal
• Rocznik: 2020
• Tom: Vol. 14, no 1
• Strony: 89--95
• Opis fizyczny: Bibliogr. 16 poz., fig., tab.

Twórcy

autor

Petrů Jana

• Faculty of Mechanical Engineering, VSB-Technical University of Ostrava, 17. listopadu 2172/15, Ostrava Poruba 708 00, Czech Republic

autor

Drábek Lukáš

• Faculty of Mechanical Engineering, VSB-Technical University of Ostrava, 17. listopadu 2172/15, Ostrava Poruba 708 00, Czech Republic

autor

Hajnyš Jiří

• Faculty of Mechanical Engineering, VSB-Technical University of Ostrava, 17. listopadu 2172/15, Ostrava Poruba 708 00, Czech Republic

autor

Jurok Dalibor

• Faculty of Mechanical Engineering, VSB-Technical University of Ostrava, 17. listopadu 2172/15, Ostrava Poruba 708 00, Czech Republic

autor

Pagáč Marek

• Faculty of Mechanical Engineering, VSB-Technical University of Ostrava, 17. listopadu 2172/15, Ostrava Poruba 708 00, Czech Republic

autor

Měsíček Jakub

• Faculty of Mechanical Engineering, VSB-Technical University of Ostrava, 17. listopadu 2172/15, Ostrava Poruba 708 00, Czech Republic

Bibliografia

• 1. Görög A., D. Stančeková, M. Kapustová, I. Görögová, I. Miturska, Influence of Selected Cutting Conditions on Cutting Forces. Advances in Science and Technology-Research Journal, (2017)
• 2. Sliva A., R. Brazda, A. Prochazka, G. S. Martynkova, K. C. Barabaszova, Investigation of geometric properties of modified titanium white by fluidisation for use in the process of transport, handling, processing and storage. Journal of nanoscience and nanotechnology. 2997 – 3001 (2019)
• 3. Barnett-Ritcey, D., Elbastawi, M.A., Tool performance in high speed finish milling of Ti6Al4V. American Society of Mechanical Engineers, Manufacturing Engineering Division, MED, 211 – 219 (2002)
• 4. Guilin, L., Research on tool wearing on milling of TC21 titanium alloy. IOP Conference Series: Earth and Environmental Science, (2017)
• 5. Kratochvíl J., M. Sadílek, J. Mrazik, The effect of chip former on power loading of recessing tool. Advances in Science and Technology-Research Journal, (2017)
• 6. Ji, W., Liu, X., Wang, L., Sun, S., Experimental evaluation of polycrystalline diamond (PCD) tool geometries at high feed rate in milling of titanium alloy TC11. International Journal of Advanced Manufacturing Technology, 1549 – 1555 (2015)
• 7. Kopierfräser [online]. In: . IngersollGmbh, 2017 [cit. 2017–03–05]. Available: http://www.imccom-panies.com/Ingersollcatalog/Item.aspx?cat=30633 22&fnum=174&mapp=ML&GFSTYP=M.
• 8. Li, A., Zhao, J., Hou, G, Effect of cutting speed on chip formation and wear mechanisms of coated carbide tools when ultra-high-speed face milling titanium alloy Ti-6Al-4V. Advances in Mechanical Engineering, (2017)
• 9. Liu, J. J., Chen, C., Yang, Y. F., Li, L., Zhao, W., Experimental research of milling force and cutting temperature of TB2 titanium alloy in liquid nitrogen cooling. Materials Science Forum, 36 – 42 (2016)
• 10. Member IMC group [online]. In: . Ingersoll 2017 [cit. 2017–03–05]. Available: http://ecat.ingersoll-imc.com/ecat/ProductDetails.aspx?ID=17895.
• 11. Microtes [online]. In: Mitutoyo, 2017 [cit. 2017–03–05]. Available: http://www.microtes.cz/ Mitutoyo/drsnomery-SJ210aSJ301-M.pdf.
• 12. Okada, M., Hosokawa, A., Askawa, N., Ueda, T., End milling of stainless steel and titanium alloy in an oil mist environment. International Journal of Advanced Manufacturing Technology, 1255 – 1266 (2014)
• 13. Safari, H., Sharif, S., Izman, S., Jafari, H., Surface integrity characterization in high-speed dry end milling of Ti-6Al-4V titanium alloy. International Journal of Advanced Manufacturing Technology, 651 – 657 (2015)
• 14. Sun, H., Xiao, H., Li, L., Experimental study on cutting force and cutting power in high feed milling of Ti5Al5Mo5VCrFe. Materials Science Forum, 88 – 93 (2015)
• 15. Schindlerová V., I. Šajdlerová, Influence of Tool Wear on Material Flow. Advances in Science and Technology-Research Journal, (2017)
• 16. Xu, J., Rong, B., Zhang, H.Z., Wang, D.S., Li, L., Investigation of cutting force in high feed milling of Ti6Al4V. Materials Science Forum, 106 – 109 (2013)

Uwagi

Opracowanie rekordu ze środków MNiSW, umowa Nr 461252 w ramach programu "Społeczna odpowiedzialność nauki" - moduł: Popularyzacja nauki i promocja sportu (2020).