Integrated multimotor electrical dc drive for metallurgical rolling table

• Autorzy: Gała M. , Jąderko A. , Rak J. , Jagiełła K.
• Języki publikacji: EN

Abstrakty

EN

A drive system of a section of a metallurgical rolling table consisting of six dc motors, 2220 amperes of total current, fed from a single ABB reversible thyristor converter has been described in this paper. Autonomous excitation circuits of the motors are fed from independent thyristor converters working in the so called MULTIFEX system linked with a supervisory high power converter. There are presented schemes of the DSL communication realized by FEX excitation cards of the motors using the SDSC card of the DCS-800-S02 converter and logic control system based on a PLC controller. The parameterization of the DCS-800 converter and the DCF 803 excitation systems was conducted using the DriveWindow software tool. Significant waveforms of voltages, currents and the estimated motor velocity are described and presented for the idle run as well as during transporting sheets discharged from a pusher furnace.

Słowa kluczowe

EN

FEX excitation system; DC drive system; rolling table; DriveWindow software

PL

system napędowy; DSL; sterowniki PLC

• Wydawca: Oficyna Wydawnicza Politechniki Białostockiej
• Czasopismo: Acta Mechanica et Automatica
• Rocznik: 2015
• Tom: Vol. 9, no. 2
• Strony: 93--98
• Opis fizyczny: Bibliogr. 12 poz., rys., tab., wykr.

Twórcy

autor

Gała M.

• Faculty of Electrical Engineering, Czestochowa University of Technology, Al. Armii Krajowej 17, 42-200 Częstochowa, Poland

autor

Jąderko A.

• Faculty of Electrical Engineering, Czestochowa University of Technology, Al. Armii Krajowej 17, 42-200 Częstochowa, Poland

autor

Rak J.

• Faculty of Electrical Engineering, Czestochowa University of Technology, Al. Armii Krajowej 17, 42-200 Częstochowa, Poland

autor

Jagiełła K.

• Faculty of Management, Czestochowa University of Technology, Al. Armii Krajowej 17, 42-200 Częstochowa, Poland

Bibliografia

• 1. Abu-Rub H., Guziński J., Jąderko A., Krzemiński Z. (2004), Practical Realisation of New Method of Synchronisation for Controlled Rectifier, International Conference on Power Electronics, Intelligent Motions and Power Quality PCIM 2004, Nuremberg, Germany, 533 – 538.
• 2. Abu-Rub H., Guziński J., Jąderko A., Krzemiński Z. (2005), Digital Implementation of a Novel Controlled Rectifier Synchronization Method, Electric Power Components and Systems, Vol. 33 (10), 1123 – 1135.
• 3. Dobrucki W., Gregorczyk R., Świątoniowski A., Zawada S. (1991), Introduction to design and operation of rolling mills – Calculations and experiments, Wydawnictwo AGH, Kraków, (in Polish).
• 4. Friedli T., Hartmann M., Kolar J.W. (2014), The Essence of ThreePhase PFC Rectifier Systems—Part II, IEEE Transactions on Power Electronics, Volume: 29 (2), 543- 560.
• 5. Gała M., Rak J., Kępiński M., Jagieła K. (2009), Application of Drive Window software for AC and DC drives operation states diagnostics, Electric Machines - Problem Issues, No.82/2009, BOBRME KOMEL Katowice, 33-38, ISSN 0239-3646, (in Polish).
• 6. Guziński J., Diaguet M., Krzemiński Z., Lewicki A., Abu-Rub H. (2009), Application of speed and load torque observers in high-speed train drive for diagnostic purposes, IEEE Transactions on Industrial Electronics, Vol 57(2), 565-574.
• 7. Jagieła K. (1997), Theoretical issues in calculation of load parameters of rolling table motors. Research Notes of Lvov State University of Technology – Electrical power engineering and electro-mechanical systems Systemy, № 340, 142-147, (in Ukrainian).
• 8. Jagieła K. (2003), Model of metallurgical discharge rolling table, Electrical Review, No.6/2003, 448- 452.
• 9. Jagieła K., Gała M. (2008), Setting screw electrical drive of the vertical milling cage using MASTER– FOLLOWER control, IX Inter-national Scientific Conference „New Technologies in Metallurgy and Materials Engineering”, Metallurgy Committee PAS, Czestochowa University of Technology, Vol. 1, 146-149 (in Polish).
• 10. Kolar J. W., Friedli T. (2013), The Essence of Three-Phase PFC Rectifier Systems—Part I, IEEE Transactions on Power Electronics, Volume: 28 (1), 176-198.
• 11. Michael C.A., Safacas A.N. (2007), Dynamic and Vibration Analysis of a Multimotor DC Drive System With Elastic Shafts Driving a Tissue Paper Machine, IEEE Transactions on Industrial Electronics, Vol. 54 (4), 2033-2046.
• 12. Multifex motor control for roller tables DCS800 Drives (20 to 5200 A), ABB Automation Products, Germany, 05-2008.