Morphological filtration of two-process profiles

• Autorzy: Pawlus P. , Reizer R. , Łętocha A. , Wieczorowski Michał

Identyfikatory

DOI

10.24425/bpas.2019.127339

• Języki publikacji: EN

Abstrakty

EN

Applications of morphological filters for two-process profiles were analysed. Dilation, closing and alternating sequential (closing + opening) filters were used with a circle (disk) as a structuring element. An original method of a disk radius selection was elaborated for two-process profiles. This procedure was applied for many simulated and measured profiles. Behaviors of morphological filters were compared with those of double Gaussian (Rk) filter. Robust filter was also taken into consideration. In calculation, TalyMap software was used. The proposed procedure was found to be very useful. It was developed for 2D profiles but it can be easily extended for an areal (3D) surface topography filtering. From among morphological filters, the alternate sequential filter is suggested.

Słowa kluczowe

EN

morphological filtration; surface topography; stratified textures

PL

filtracja morfologiczna; topografia powierzchni; warstwowa tekstura

• Wydawca: Polska Akademia Nauk, Wydział IV Nauk Technicznych
• Czasopismo: Bulletin of the Polish Academy of Sciences. Technical Sciences
• Rocznik: 2019
• Tom: Vol. 67, nr 1
• Strony: 107--113
• Opis fizyczny: Bibliogr. 21 poz., wykr., rys.

Twórcy

autor

Pawlus P.

• Rzeszow University of Technology, Rzeszow, Poland

autor

Reizer R.

• University of Rzeszow, Centre for Innovative Technologies, Rzeszow, Poland

autor

Łętocha A.

• Institute of Advanced Manufacturing Technology, Cracow, Poland

autor

Wieczorowski Michał

• Poznan University of Technology, Poznan, Poland

Bibliografia

• [1] S. Adamczak and P. Zmarzły, “Influence of raceway waviness on the level of vibration in rolling-element bearings”, Bull. Pol. Ac.: Tech. 65 (4), 541‒551 (2017).
• [2] S. Adamczak, P. Zmarzły, and K. Stępień, “Identification and analysis of optimal method parameters of the V-block waviness measurements”, Bull. Pol. Ac.: Tech. 64 (2), 325‒332 (2016).
• [3] M.S. Shunmugam and V. Radhakrishman,”Two- and three dimensional analyses of surfaces according to the E-system”, Proceedings of the Institution of Mechanical Engineers, 188, 691‒699 (1974).
• [4] P.J. Scott, “Scale-space techniques”, X International Colloquium on Surfaces. Chemnitz, Germany, 153‒161 (2000).
• [5] S. Lou, X. Jiang, and P.J. Scott, “Application of morphological operations in surface metrology and dimensional metrology”, Proceedings of the 14th International Conference on Metrology and Properties of Engineering Surfaces, Taipei, Taiwan (2013).
• [6] C.M. Malburg, “Surface profile analysis for conformable surfaces”, Transactions of The ASME, Journal of Manufacturing Science and Engineering, 125, 624‒627 (2003).
• [7] S. Lou, X. Jiang, and P.J. Scott, “Algorithms for morphological profile filters and their comparison”, Precision Engineering, 36, 414‒423 (2012).
• [8] Y. Jeng, “Impact of plateaued surfaces on tribological performance”, Tribology Transactions, 39(2), 354‒356 (1996).
• [9] W. Grabon, P. Pawlus, and J. Sep, “Tribological characteristics of one-process and two-process cylinder liner honed surfaces under reciprocating sliding conditions”, Tribology International, 43(10), 1882‒1892 (2010).
• [10] A. Dzierwa, P. Pawlus, and W. Zelasko, “Comparison of tribological behaviors of one-process and two-process steel surfaces in ball-on-disc tests”, Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology, 228, 1195‒1210 (2014).
• [11] P. Pawlus and W, Grabon, “The method of truncation parameters measurement from material ratio curve”, Precision Engineering 32, 342‒347 (2008).
• [12] I. Etsion, “State of the art in laser surface texturing”, Proceedings of the 12th Conference on Metrology and Properties of Engineering Surfaces, Rzeszow, Poland, 17‒20 (2009).
• [13] P. Pawlus, R. Reizer, M. Wieczorowski, and W. Żelasko, “The effect of sampling interval on the predictions of an asperity contact model of two-process surfaces”, Bull. Pol. Ac.: Tech. 65 (3), 391‒398 (2017).
• [14] D.J. Whitehouse, “Some theoretical aspects of a practical measurement problem in plateau honing”, Int. J. Prod. Res. 21 (2), 215‒221 (1983).
• [15] L. Mummery, “Surface texture analysis, the handbook”, Hommelwerke GmbH, 1990.
• [16] S. Brinkman and H. Bodschwinna, “Advanced Gaussian filters”, in Assessment surface topography, pp. 62‒89, eds. L. Blunt and X. Jiang, Kogan Page Science, London and Sterling, 2003.
• [17] B. Muralikrishnan and J. Raja, “Functional filtering and performance correlation of plateau honed surface profiles”, Manufacture science and Engineering, 127, 193‒197 (2005).
• [18] W. Grabon, P. Pawlus, L. Galda, A. Dzierwa, and P. Podulka, „Problems of surface topography with oil pockets analysis”, J. Phys. Conf. Ser., 311, 012023 (2011).
• [19] P. Podulka, P. Dobrzanski, P. Pawlus, and A. Lenart, “The effect of reference plane on values of areal surface topography parameters from cylindrical elements”, Metrology and Measurement Systems, 21(2), 247‒256 (2014).
• [20] P. Pawlus, R. Reizer, and M. Wieczorowski, “The analysis of directionality of honed cylinder liners surfaces”, Scanning, 36(1), 95‒104 (2014).
• [21] P. Podulka, P. Pawlus, P. Dobrzanski, and A. Lenart, “Spikes removal in surface measurement”, J. Phys. Conf. Ser., 483(1), 012025 (2014).

Uwagi

PL

Opracowanie rekordu w ramach umowy 509/P-DUN/2018 ze środków MNiSW przeznaczonych na działalność upowszechniającą naukę (2019).