Effect of Shot Peening With Glass Microspheres on the Fatigue Behavior of a Low Carbon Steel

• Autorzy: de Lacerda J. C. , Pereira I. R. , Costa J. M. G. , Pinto J. S. , Souza H. F. M. , Fonseca M. A.

Identyfikatory

DOI

10.24425/amm.2019.130120

• Języki publikacji: EN

Abstrakty

EN

The present work has the objective of studying the effect of shot peening with glass microspheres on SAE 1020 steel in its resistance to fatigue. Fatigue tests were carried out by rotary bending with load control and loading on balance in specimens with and without shot peening. A rotation speed of approximately 750 rpm (12.5 Hz) was employed in the fatigue tests. Vickers microhardness tests were performed in order to verify the surface hardening produced by shot peening with glass microspheres. Analysis of the steel surface and fatigue fractures was performed using scanning electron microscopy (SEM). Fatigue tests were performed in order to obtain S-N curves (Wöhler curves). It was observed that shot peening with glass microspheres improved the fatigue strength of the steel at high cycle.

Słowa kluczowe

EN

fatigue; shot peening; Wöhler curve; low carbon steel; glass microspheres

• Wydawca: Institute of Metallurgy and Materials Science of Polish Academy of Sciences ; Committee of Materials Engineering and Metallurgy of Polish Academy of Sciences
• Czasopismo: Archives of Metallurgy and Materials
• Rocznik: 2019
• Tom: Vol. 64, iss. 4
• Strony: 1513--1518
• Opis fizyczny: Bibliogr. 25 poz., fot., rys., tab., wzory

Twórcy

autor

de Lacerda J. C.

• Universidade Federal de Itajubá - Campus Itabira, 35900-000 - Itabira MG - Brazil

autor

Pereira I. R.

• Universidade Federal de Itajubá - Campus Itabira, 35900-000 - Itabira MG - Brazil

autor

Costa J. M. G.

• Universidade Federal de Itajubá - Campus Itabira, 35900-000 - Itabira MG - Brazil

autor

Pinto J. S.

• Centro Universitário do Leste de Minas Gerais - Campus Coronel Fabriciano, 35170-056 - Coronel Fabriciano MG - Brazil

autor

Souza H. F. M.

• Centro Universitário do Leste de Minas Gerais - Campus Coronel Fabriciano, 35170-056 - Coronel Fabriciano MG - Brazil

autor

Fonseca M. A.

• Centro Universitário do Leste de Minas Gerais - Campus Coronel Fabriciano, 35170-056 - Coronel Fabriciano MG - Brazil

Bibliografia

• [1] T. Klotza, D. Delberguea, P. Bocherb, M. Lévesquea, M. Brochua. International Journal of Fatigue 110, 10-21 (2018).
• [2] L. Hua, P. Fenga, Xiao-Ling, Thin-Walled Structures 119, 482-498 (2017).
• [3] A. Akyel, M. H. Kolstein, F.S.K. Bijlaard, Engineering Structures 161, 28-40 (2018).
• [4] M. Kamala, M. M. Rahman, Renewable and Sustainable Energy Reviews 82, 940-949 (2018).
• [5] D. Angelova, R. Yordanova, S. Yankov, Engineering Failure Analysis 82, 350-363 (2017).
• [6] Y. Wang, E. I. Meletis, H. Huang, International Journal of Fatigue. 48, 280-288 (2013).
• [7] L. Kubin, M. Sauzay, Acta Materialia. 104, 295-302 (2016).
• [8] J. C. de Lacerda, G. D. Martins, V. T. Signoretti, R.L.P. Teixeira, International Journal of Fatigue. 102, 143-148 (2017).
• [9] H. Y. Li, H. L. Sun, P. Bowen, J. F. Knott, International Journal of Fatigue 108, 53-61 (2018).
• [10] M.A.S. Torres, H.J.C. Voorwald, International Journal of Fatigue 24, 877-886 (2002).
• [11] C. G. Schön, Mecânica dos materiais: Fundamentos e Tecnologia do Comportamento Mecânico. Elsevier, (2013).
• [12] M. P. Nascimento, R. C. Souza, W. L. Pigatin, H.J.C. Voorwald, International Journal of Fatigue 23, 607-618 (2001).
• [13] Yu-kui Gao, Xiang-bin Li, Qing-xiang Yang, Mei Yao. Materials Letters 61, 466-469 (2007).
• [14] B. N. Mordyuk, G. I. Prokopenko, P. Yu. Volosevich, L. E. Matokhnyuk, A. V. Byalonovich, T. V. Popova, Materials Science & Engineering A 659, 119-129 (2016).
• [15] B. N. Mordyuk, G. I. Prokopenko, K. E. Grinkevych, N. A. Piskun, T. V. Popova, Surface & Coatings Technology 309, 969-979 (2017).
• [16] Y. K. Gao. Materials Science and Engineering A 528, 3823-3828 (2011).
• [17] E. Maleki, O. Unalb, K. R. Kashyzadeha, Surface & Coatings Technology 344, 62-64 (2018).
• [18] E. Maleki, A. Zabihollah, Mater. Technol. 50 (6), 43-52 (2016).
• [19] R. Valiev, Nat. Mater. 3, 511-516 (2004).
• [20] Y. Estrin, A. Vinogradov, Acta Mater. 61, 782-817 (2013).
• [21] ASTM E-8M. Standard test method for tension testing of metallic materials (metric), (1995).
• [22] C. Karatas, A. Sozen, E. Dulek, Expert Systems with Applications 36, 3514-3521 (2009).
• [23] J. Hensel, T. Nitschke-Pagel, D. T. Ngoula, H.-Th. Beier, Tchuindjang U. Zerbst, Engineering Fracture Mechanics 198, 123-14 (2018).
• [24] B. Gao, Y. Li, T. Fu Guo, X. Guo, S. Tang, Extreme Mechanics Letters 22, 42-50 (2018).
• [25] V. Tvergaard, International Journal of Mechanical Sciences 133, 631-63 (2017).

Uwagi

EN

The authors would like to thank Unileste (Centro Universitário do Leste de Minas Gerais) and UNIFEI (Universidade Federal de Itajubá - Campus Itabira) for providing the technical support and infrastructure necessary to carry out the experiments.