Characteristics of ADI Ductile Cast Iron with Single Addition of 1.56% Ni

• Autorzy: Mrzygłód B. , Kowalski A. , Olejarczyk-Wożenska I. , Giętka T. , Głowacki M.

Identyfikatory

DOI

10.1515/amm-2017-0335

• Języki publikacji: EN

Abstrakty

EN

The results of examinations of microstructure and an analysis of its impact on selected mechanical properties of austempered ductile iron (ADI) were presented in the paper. The ADI was produced from the ductile iron containing 1.56% Ni only alloying addition. The effect of the austempering time and temperature on the microstructure and mechanical properties of the examined cast iron was considered. Constant conditions of austenitizing were assumed and six variants of the austempering treatment were adopted. The studyof mechanical properties included a static tensile test, Charpy impact strength test and Brinellhardness measurement. This work complements the knowledge about alloying additions effect on microstructure and mechanical properties of ADI and focuses on the impact of a single alloying element (Ni).

Słowa kluczowe

EN

ductile iron; heat treatment; structure of ADI; ADI properties

• Wydawca: Institute of Metallurgy and Materials Science of Polish Academy of Sciences ; Committee of Materials Engineering and Metallurgy of Polish Academy of Sciences
• Czasopismo: Archives of Metallurgy and Materials
• Rocznik: 2017
• Tom: Vol. 62, iss. 4
• Strony: 2273--2280
• Opis fizyczny: Bibliogr. 14 poz., rys., tab., wykr.

Twórcy

autor

Mrzygłód B.

• AGH University of Science and Technology, Faculty of Metals Engineering and Industrial Computer Science, Al. A. Mickiewicza 30, 30-059 Kraków, Poland

autor

Kowalski A.

• Foundry Research Institute, 73 Zakopiańska Str., 30-418 Kraków, Poland

autor

Olejarczyk-Wożenska I.

• AGH University of Science and Technology, Faculty of Metals Engineering and Industrial Computer Science, Al. A. Mickiewicza 30, 30-059 Kraków, Poland

autor

Giętka T.

• UTP University of Science and Technology of Mechanical Engineering, 7 Prof. S. Kaliskiego Av., 85-796 Bydgoszcz

autor

Głowacki M.

• AGH University of Science and Technology, Faculty of Metals Engineering and Industrial Computer Science, Al. A. Mickiewicza 30, 30-059 Kraków, Poland

Bibliografia

• [1] C. Podrzucki, Problemy produkcji odlewów z żeliwa sferoidalnego ADI. Przegląd Odlewnictwa 10, 260-265 (1996).
• [2] Multiple advantages of austempered ductile iron. ADI being chosen over aluminum. Modern Casting 9, 15-16 (1999).
• [3] J. F. Janowak, P. A. Morton, A guide to mechanical properties possible by austempered 1,5% Ni-0,3% Mo ductile iron. Transactions AFS, 489-498 (1984).
• [4] M. Grech, J. M. Young, Impact properties of a Cu-Ni austempered ductile iron. Cast Metals 1/2, 98,(1988).
• [5] A. Kowalski, J. Tybulczuk, Experience of The Foundry Research Institute Krakow in investigation and application of Ni-Cu ADI for castings. 42 Livarsko Strokovno Posvetovanje. Slovenja, Portoroż 23-24 May 2002, (2002).
• [6] R. H. Juneja, et al., Austempering ductile iron alloyed with coper and manganese, Foundry 64, (1989).
• [7] E. Dorazil, Zwischenstufenumwandeln von Gusseisen mit Kugel-graphit, Giesserei-Praxis 18, 355 (1979).
• [8] K. L. Hayrynen, The production of austempered ductile iron (ADI). World Conference of ADI. Livonia, Michigan, USA, (2002).
• [9] A. Owhadi, et al., Wear behavior of 1.5 Mn austempered ductile iron, Materials Science and Technology 14, 245 (1998).
• [10] M. N. Ahamadabadi, E. Niyama, T. Ohide, Structural control of 1% Mn ADI aided by modeling of microsegregation, Transactions AFS, 269 (1994).
• [11] Z. Pirowski, et al., Wpływ mikrododatku boru na zmiany hartowności w żeliwie sferoidalnym z przemianą izotermiczną w odniesieniu do odlewów grubościennych, Journal of Research and Applications in Agricultural Engineering 57 (2), 153-155, (2012).
• [12] S. Kluska-Nawarecka, D. Wilk-Kołodziejczyk, K. Regulski, et al., Rough Sets Applied to the Rough Cast System for Steel Castings, Lecture Notes in Artificial Intelligence 6592, 52-61 (2011).
• [13] B. Sniezynski, G. Legien, D. Wilk-Kolodziejczyk, et al., Creative Expert System: Result of Inference and Machine Learning Integration, Lecture Notes in Computer Science 9827, 257-271 (2016).
• [14] D. Wilk-Kolodziejczyk, B. Mrzyglod, K. Regulski, et al., Influence of process parameters on the properties of austernpered ductile iron (adi) examined with the use of data mining methods, Metalurgija 55 (4), 849-851 (2016).

Uwagi

EN

Financial assistance of the NCN, project No. 13/11/N/ST8/00326

PL

Opracowanie rekordu w ramach umowy 509/P-DUN/2018 ze środków MNiSW przeznaczonych na działalność upowszechniającą naukę (2018).