Powiadomienia systemowe
- Sesja wygasła!
- Sesja wygasła!
Tytuł artykułu
Treść / Zawartość
Pełne teksty:
Identyfikatory
Warianty tytułu
Języki publikacji
Abstrakty
The general topic of this paper is the computer simulation with use of finite element method (FEM) for determining the internal stresses of selected gradient and single-layer PVD coatings deposited on the sintered tool materials, including cemented carbides, cermets and Al2O3+TiC type oxide tool ceramics by cathodic arc evaporation CAE-PVD method. Developing an appropriate model allows the prediction of properties of PVD coatings, which are also the criterion of their selection for specific items, based on the parameters of technological processes. In addition, developed model can to a large extent eliminate the need for expensive and time-consuming experimental studies for the computer simulation. Developed models of internal stresses were performed with use of finite element method in ANSYS environment. The experimental values of stresses were calculated using the X-ray sin2ψ technique. The computer simulation results were compared with the experimental results. Microhardness and adhesion as well as wear range were measured to investigate the influence of stress distribution on the mechanical and functional properties of coatings. It was stated that occurrence of compressive stresses on the surface of gradient coating has advantageous influence on their mechanical properties, especially on microhardness. Absolute value reduction of internal stresses in the connection zone in case of the gradient coatings takes profitably effects on improvement the adhesion of coatings. It can be one of the most important reasons of increase the wear resistance of gradient coatings in comparison to single-layer coatings.
Słowa kluczowe
Wydawca
Czasopismo
Rocznik
Tom
Strony
149--152
Opis fizyczny
Bibliogr. 13 poz., rys., tab.
Twórcy
autor
- Silesian University of Technology, Institute of Engineering Materials and Biomaterials, 18 A Konarskiego Str., 44-100 Gliwice, Poland
autor
- Silesian University of Technology, Institute of Engineering Materials and Biomaterials, 18 A Konarskiego Str., 44-100 Gliwice, Poland
autor
- Silesian University of Technology, Institute of Engineering Materials and Biomaterials, 18 A Konarskiego Str., 44-100 Gliwice, Poland
autor
- Silesian University of Technology, Institute of Engineering Materials and Biomaterials, 18 A Konarskiego Str., 44-100 Gliwice, Poland
autor
- Silesian University of Technology, Institute of Engineering Materials and Biomaterials, 18 A Konarskiego Str., 44-100 Gliwice, Poland
autor
- Silesian University of Technology, Institute of Engineering Materials and Biomaterials, 18 A Konarskiego Str., 44-100 Gliwice, Poland
autor
- Silesian University of Technology, Institute of Engineering Materials and Biomaterials, 18 A Konarskiego Str., 44-100 Gliwice, Poland
Bibliografia
- [1] L. A. Dobrzański, A. Śliwa, W. Sitek, Surf. Eng. 5, Seattle (2006).
- [2] L. A. Dobrzański, M. Staszuk, K. Gołombek, A. Śliwa, M. Pancielejko, Arch. Metall., Mat. 55, 187 (2010).
- [3] L. A. Dobrzański, W. Kwaśny, B. Dołżańska, A. Śliwa , K. Gołombek, G. Nowak, Arch. Mater. Sci. Eng. 57, 38 (2012).
- [4] Ł. Szparaga, J. Ratajski, Adv. Mater. Sci. Eng. 14, 5 (2014).
- [5] A. Śliwa, T. Tański, R. Dziwis, W. Kwaśny, M. Pancielejko, Arch. Mater. Sci. Eng. 64, 28 (2013).
- [6] A. Śliwa, W. Kwaśny, L.A. Dobrzański, R. Dziwis, Arch. Mater. Sci. Eng. 63, 68 (2013).
- [7] L. A. Dobrzański, L. W. Żukowska, J. Mikuła , K. Gołombek, D. Pakuła, M. Pancielejko, J. Mat. Proc. Tech. 201, 310 (2008).
- [8] K. Lukaszkowicz, A. Czyzniewski, W. Kwasny, M. Pancielejko, Vac. 86, 1186 (2012).
- [9] L. A. Dobrzański, D. Pakula, J. Mikula, K. Golombek, Inter. J. Surf. Sci. Eng. 1, 111 (2012).
- [10] L. A. Dobrzański, J. Mikuła, K. Gołombek, Mater. Sci. Forum, 530-531, 499 (2006).
- [11] V . Valvoda, J. Alloys Compd 219, 83 (1995).
- [12] M. Staszuk, L.A. Dobrzański, T. Tański, W. Kwaśny, M. Musztyfaga-Staszuk, Arch. Metall., Mat. 59, 269 269-274 (2014).
- [13] L. Żukowska, J. Mikuła, M. Staszuk, M. Musztyfaga- Staszuk, Arch. Metall. Mat. 2, (2015) (in press).
Uwagi
Opracowanie ze środków MNiSW w ramach umowy 812/P-DUN/2016 na działalność upowszechniającą naukę
Typ dokumentu
Bibliografia
Identyfikator YADDA
bwmeta1.element.baztech-e3c83302-89da-4ae5-bfcc-693ec3e2e097