Influence of drill bit material on the bearing strength of holes in GFRP composite

• Autorzy: Galińska Anna

Identyfikatory

DOI

10.24425/ame.2023.144818

• Języki publikacji: EN

Abstrakty

EN

The article aims at assessing the influence of the drill bit material on the bearing strength of holes made in glass fabric reinforced epoxy composite. Six twists made of widely used drill materials such as high speed steels and carbides in different configurations were selected to drill holes in the composite. In the first stage of the work, optimum drilling parameters were selected and then used for drilling holes in specimens tested in single lap shear experiments. For each tested specimen two different delamination factors, one based on the delamination area and another - on its diameter, were calculated in order to assess the quality of the holes and then compared to the results of the bearing strength experiments. The results of the bearing tests showed that the highest strength was achieved for the high speed steel drill with titanium coating while the lowest for the cemented carbide drill. This finding is in opposition to the majority of results reported in literature.

Słowa kluczowe

EN

fibre reinforced composites; drilling; bolted joining; bearing strength; delamination

PL

kompozyty wzmocnione włóknami; wiercenie; łączenie śrubowe; wytrzymałość nośna; rozwarstwienie

• Wydawca: Komitet Budowy Maszyn PAN
• Czasopismo: Archive of Mechanical Engineering
• Rocznik: 2023
• Tom: LXX, nr 2
• Strony: 287--310
• Opis fizyczny: Bibliogr. 58 poz., rys., tab.

Twórcy

autor

Galińska Anna

• Warsaw University of Technology, Faculty of Power and Aeronautical Engineering, Warsaw, Poland

• https://orcid.org/0000-0001-7992-1547

Bibliografia

• [1] I.S. Shyha, S.L. Soo, D. Aspinwall, and S. Bradley. Effect of laminate configuration and feed rate on cutting performance when drilling holes in carbon fibre reinforced plastic composites. Journal of Materials Processing Technology, 210(8):1023–1034, 2010. doi: 10.1016/j.jmatprotec.2010.02.011.
• [2] L.N. Lopez de Lacalle, A. Lamikiz, F.J. Campa, A.F. Valdivielso, and I. Etxeberria. Design and test of multi-tooth tool for CFRP milling. Journal of Composite Materials, 43(26):3275–3290, 2009. doi: 10.1177/0021998309345354.
• [3] X. Cheng, S. Wang, J. Zhang, W. Huang, Y. Cheng, and J. Zhang. Effect of damage on failure mode of multi-bolt composite joints using failure envelope method. Composite Structures, 160:8-15, 2017. doi: 10.1016/j.compstruct.2016.10.042.
• [4] S. Gaugel P. Sripathy, A. Haeger, D. Meinhard, T. Bernthaler, F. Lissek, M. Kaufeld, V. Knoblauch, and G. Schneider. A comparative study on tool wear and laminate damage in drilling of carbon-fiber reinforced polymers (CFRP). Composite Structures, 155:173–183, 2016. doi: 10.1016/j.compstruct.2016.08.004.
• [5] Y. Turki, M. Hebak, R. Velasco, Z. Aboura, K. Khellil, and P. Vantomme. Experimental investigation of drilling damage and stitching effects on the mechanical behavior of carbon/epoxy composites. International Journal of Machine Tools and Manufacture, 87:61–72, 2014. doi: 10.1016/j.ijmachtools.2014.06.004.
• [6] C.C. Tsao, H. Hocheng, and Y.C. Chen. Delamination reduction in drilling composite materials by active backup force. CIRP Annals – Manufacturing Technology, 61(1):91-94, 2012. doi: 10.1016/j.cirp.2012.03.036.
• [7] J. Xu. Manufacturing of fibrous composites for engineering applications. Journal of Composites Science, 6(7):187, 2022. doi: 10.3390/jcs6070187.
• [8] J. Xu, X. Huang, M. Chen, and J.P. Davim. Drilling characteristics of carbon/epoxy and carbon/polyimide composites. Materials and Manufacturing Processes, 35(15):1732–1740, 2020. doi: 10.1080/10426914.2020.1784935.
• [9] D. Geng, Y, Liu, Z. Shao, Z. Lu, J. Cai, X. Li, X. Jiang, and D. Zhang. Delamination formation, evaluation and suppression during drilling of composite laminates: A review. Composite Structures, 216:168–186, 2019. doi: 10.1016/j.compstruct.2019.02.099.
• [10] R. Stone and K. Krishnamurthy. A neural network thrust force controller to minimize delamination during drilling of graphite-epoxy laminates. International Journal of Machine Tools and Manufacture, 36(9):985–1003, 1996. doi: 10.1016/0890-6955(96)00013-2.
• [11] L. Sorrentino, S. Turchetta, and C. Bellini. A new method to reduce delaminations during drilling of FRP laminates by feed rate control. Composite Structures, 186:154–164, 2018. doi: 10.1016/j.compstruct.2017.12.005.
• [12] A. Galińska. Mechanical joining of fibre reinforced polymer composites to metals – A review. Part I: bolted joining. Polymers, 12(10):2252, 2020. doi: 10.3390/polym12102252.
• [13] R. Bielawski, M. Kowalik, K. Suprynowicz, W. Rządkowski, and P. Pyrzanowski. Investigation of riveted joints of fiberglass composite materials. Mechanics of Composite Materials, 52:199–210, 2016. doi: 10.1007/s11029-016-9573-4.
• [14] P. Dobrzański and W. Oleksiak. Design and analysis methods for composite bonded joints. Transactions on Aerospace Research, 2021(1):45–63, 2021. doi: 10.2478/tar-2021-0004.
• [15] C.C. Tsao. Effect of pilot hole on thrust force by saw drill. International Journal of Machine Tools and Manufacture, 47(14):2172–2167, 2007. doi: 10.1016/j.ijmachtools.2007.05.008.
• [16] X. Qiu, P. Li, Q. Niu, A. Chen, P. Ouyang, C. Li, and T.J. Ko. Influence of machining parameters and tool structure on cutting force and hole wall damage in drilling CFRP with stepped drills. The International Journal of Advanced Manufacturing Technology, 97:857–865, 2018. doi: 10.1007/s00170-018-1981-2.
• [17] A. Guputa, H. Ascroft, and S. Barnes. Effect of chisel edge in ultrasonic assisted drilling of carbon fibre reinforced plastics (CFRP). Procedia CIRP, 46:619–622, 2016. doi: 10.1016/j.procir.2016.04.026.
• [18] J. Ramkumar, S. Aravindan, S.K. Malhotra, and R. Krishnamurthy. An enhancement of the machining performance of GFRP by oscillatory assisted drilling. International Journal of Advanced Manufacturing, 23:240–244, 2004. doi: 10.1007/s00170-003-1660-8.
• [19] Rampal, G. Kumar, S.M. Rangappa, S. Siengchin, and S. Zafar. A review of recent advancements in drilling of fiber-reinforced polymer composites. Composites Part C: Open Access, 9:100312, 2022. doi: 10.1016/j.jcomc.2022.100312.
• [20] H. Heidary and M.A. Mehrpouya. Effect of backup plate in drilling of composite laminates, analytical and experimental approaches. Thin-Walled Structures, 136:323–332, 2019. doi: 10.1016/j.tws.2018.12.035.
• [21] U. Koklu and S. Morkavuk. Cryogenic drilling of carbon fiber-reinforced composite (CFRP). Surface Review and Letters, 26(9):1950060, 2019. doi: 10.1142/S0218625X19500604.
• [22] J. Xu, C. Li, S. Mi, Q. An, and M. Chen. Study of drilling-induced defects for CFRP composites using new criteria. Composite Structures, 201:1076–1087, 2018. doi: 10.1016/j.compstruct.2018.06.051.
• [23] D. Kumar, K.K. Singh. And R. Zitoune. Experimental investigation of delamination and surface roughness in the drilling of GFRP composite material with different drills. Advanced Manufacturing: Polymer & Composites Science, 2(2):47–56, 2016. doi: 10.1080/20550340.2016.1187434.
• [24] L.M. Durão, A.G. Magalhães, J.M.R.S. Tavares, and A.T. Marques. Analyzing objects in images for estimating the delamination influence on load carrying capacity of composite laminates. Electronic Letters on Computer Vision and Image Analysis, 7(2):11–21, 2008. doi: 10.5565/rev/elcvia.187.
• [25] C.C. Tsao and H. Hocheng. Taguchi analysis of delamination associated with various drill bits in drilling of composite material. International Journal of Machine Tools and Manufacture, 44(10):1085–1090, 2004. doi: 10.1016/j.ijmachtools.2004.02.019.
• [26] H. Hocheng and C.C. Tsao. Effects of special drill bits on drilling-induced delamination of composite materials. International Journal of Machine Tools and Manufacture, 46(12-13):1403–1416, 2006. doi: 10.1016/j.ijmachtools.2005.10.004.
• [27] X. Qiu, P. Li, C. Li, Q. Niu, A. Chen, P. Ouyang, and T.J. Ko. Study on chisel edge drilling behavior and step drill structure on delamination in drilling CFRP. Composite Structures, 203:404–413, 2018. doi: 10.1016/j.compstruct.2018.07.007.
• [28] J.C. Rubio, A.M. Abrao, P.E. Faria, A.E. Correia, J.P. Davim. Effects of high speed in the drilling of glass fibre reinforced plastic: Evaluation of the delamination factor. International Journal of Machine Tools and Manufacture, 48(6):715–720, 2008. doi: 10.1016/j.ijmachtools.2007.10.015.
• [29] L. Gemi, S. Morkavuk, U. Koklu, and D.S. Gemi. An experimental study on the effects of various drill types on drilling performance of GFRP composite pipes and damage formation. Composites Part B: Engineering, 172:186–194, 2019. doi: 10.1016/j.compositesb.2019.05.023.
• [30] L.M. Durão, D.J.S. Goncalves, J.M.R.S. Tavares, V.H.C. de Albuquerque, A.A. Vieira, and A.T. Marques. Drilling tool geometry evaluation for reinforced composite laminates. Composite Structures, 92(7):1545–1550, 2010. doi: 10.1016/j.compstruct.2009.10.035.
• [31] A.T. Marques, L.M. Durão, A.G. Magalhães, J.F. Silva, and J.M.R.S. Tavares. Delamination analysis of carbon fibre reinforced laminates: Evaluation of a special step drill. Composites Science and Technology,, 69(14):2376–2382, 2009. doi: 10.1016/j.compscitech.2009.01.025.
• [32] N. Feito, J. Díaz-Álvarez, J. López-Puente, and M.H. Miguelez. Experimental and numerical analysis of step drill bit performance when drilling woven CFRPs. Composite Structures, 184:1147–1155, 2018. doi: 10.1016/j.compstruct.2017.10.061.
• [33] A.T. Erturk, F. Vatansever, E. Yarar, and S. Karabay. Machining behavior of multiple layer polymer composite bearing with using different drill bits. Composites Part B: Engineering, 176:107318, 2019. doi: 10.1016/j.compositesb.2019.107318.
• [34] M. Mudhukrishnan, P. Hariharan, and K. Palanikmer. Measurement and analysis of thrust force and delamination in drilling glass fiber reinforced polypropylene composites using different drills. Measurement, 149:106973, 2020. doi: 10.1016/j.measurement.2019.106973.
• [35] J. Xu, C. Li, M. Chen, M. El Mansori, F. Ren. An investigation of drilling high-strength CFRP composites using specialized drills. International Journal of Advanced Manufacturing Technology, 103 (9-12): 3425-3442, 2019. doi: 10.1007/s00170-019-03753-8.
• [36] J. Xu, T. Lin, J.P. Davim, M. Chen, and M. El Mansori. Wear behavior of special tools in the drilling of CFRP composite laminates. Wear, 476:203738, 2021. doi: 10.1016/j.wear.2021.203738.
• [37] U. Heisel and T. Pfeifroth. Influence of point angle on drill hole quality and machining forces when drilling CFRP. Procedia CIRP, 1:471–476, 2012. doi: 10.1016/j.procir.2012.04.084.
• [38] V.N. Gaitonde, S.R. Karnik, J.C. Rubio, A.E. Correia, A.M. Abrão, and J.P. Davim. Analysis of parametric influence on delamination in high-speed drilling of carbon fiber reinforced plastic composites. International Journal of Machine Tools and Manufacture, 203(1-3):431–438, 2008. doi: 10.1016/j.jmatprotec.2007.10.050.
• [39] I.S. Shyha, D.K. Aspinwall, S.L. Soo, and S. Bradley. Drill geometry and operating effects when cutting small diameter holes in CFRP. International Journal of Machine Tools and Manufacture, 49(12-13):1008–1014, 2009. doi: 10.1016/j.ijmachtools.2009.05.009.
• [40] D. Iliescu, D. Gehin, M.E. Gutierrez, and F. Girot. Modeling and tool wear in drilling of CFRP. International Journal of Machine Tools and Manufacture, 50(2):204–213, 2010. doi: 10.1016/j.ijmachtools.2009.10.004.
• [41] A. Çelik, I. Lazoglu, A. Kara, and F. Kara. Investigation on the performance of SiAlON ceramic drills on aerospace grade CFRP composites. Journal of Materials Processing Technology, 223:39–47, 2015. doi: 10.1016/j.jmatprotec.2015.03.040.
• [42] E. Kilickap. Optimization of cutting parameters on delamination based on Taguchi method during drilling of GFRP composite. Expert Systems with Applications, 37(8):6116–6122, 2010. doi: 10.1016/j.eswa.2010.02.023.
• [43] N. Feito, A.S. Milani, and A. Muñoz-Sánchez. Drilling optimization of woven CFRP laminates under different tool wear conditions: a multi-objective design of experiments approach. Structural and Multidisciplinary Optimization, 53(2):239–251, 2016. doi: 10.1007/s00158-015-1324-y.
• [44] J. Xu, Y. Yin, J.P. Davim, L. Li, M. Ji, N. Geier, and M. Chen. A critical review addressing drilling-induced damage of CFRP composites. Composite Structures, 294:115594, 2022. doi: 10.1016/j.compstruct.2022.115594.
• [45] D.I. Poor, N. Geier, C. Pereszlai, and J. Xu. A critical review of the drilling of CFRP composites: Burr formation, characterisation and challenges. Composites Part B: Engineering, 223:109155, 2021. doi: 10.1016/j.compositesb.2021.109155.
• [46] V. Krishnaraj, A. Prabukarthi, A. Ramanathan, N. Elanghovan, M.S. Kumar, R. Zitoune, and J.P. Davim. Optimization of machining parameters at high speed drilling of carbon fiber reinforced plastic (CFRP) laminates. Composites Part B: Engineering,. 43(4):1791–1799, 2012. doi: 10.1016/j.compositesb.2012.01.007.
• [47] S. Rawat and H. Attia. Characterization of the dry high speed drilling process of woven composites using Machinability Maps approach. CIRP Annals – Manufacturing Technology, 58:105–8, 2009. doi: 10.1016/j.cirp.2009.03.100.
• [48] J. Xu, T. Lin, M. Chen, and J.P. Davim. Machining responses of high-strength carbon/epoxy composites using diamond-coated brad spur drills. Materials and Manufacturing Processes, 36(6):722–729, 2021. doi: 10.1080/10426914.2020.1854475.
• [49] D. Kumar and K.K. Sing. Experimental analysis of delamination, thrust force and surface roughness on drilling of glass fibre reinforced polymer composites material using different drills. Materials Today: Proceedings, 4(8):7618–7627, 2017. doi: 10.1016/j.matpr.2017.07.095.
• [50] U.A. Khashaba, I.A. El-Sonbaty, A.I. Selmy, and A.A. Megahed. Machinability analysis in drilling woven GFR/epoxy composites: Part I – Effect of machining parameters. Composites Part A: Applied Science and Manufacturing, 41(3):391–400, 2010. doi: 10.1016/j.compositesa.2009.11.006.
• [51] K. Weinert and C. Kempmann. Cutting temperatures and their effects on the machining behaviour in drilling reinforced plastic composites. Advanced Engineering Materials, 6(8):684-689, 2004. doi: 10.1002/adem.200400025.
• [52] A. Dogrusadik and A. Kentli. Comparative assessment of support plates’ influences on delamination damage in micro-drilling of CFRP laminates. Composite Structures, 173:156–167, 2017. doi: 10.1016/j.compstruct.2017.04.031.
• [53] D. Liu, Y. Tang, and W.L. Cong. A review of mechanical drilling for composite laminates. Composite Structures, 94(4):1265-1279, 2012. doi: 10.1016/j.compstruct.2011.11.024.
• [54] C.A. Schneider, W.S. Rasband, and K.W. Eliceiri. NIH Image to ImageJ: 25 years of image analysis. Nature Methods, 9:671–675, 2012. doi: 10.1038/nmeth.2089.
• [55] P. Pieśko and M. Zawada-Michałowska, Influence of technological parameters and type of drill bit on the accuracy of holes machining in carbon fibrous composites. Mechanik, 90(12):1113–1115, 2017. doi: 10.17814/mechanik.2017.12.190.
• [56] J. Fernandez-Perez, J.L. Cantero, J. Diaz-Alvarez, and M.H. Miguelez. Influence of cutting parameters on tool wear and hole quality in composite aerospace components drilling. Composite Structures, 178:157–161, 2017. doi: 10.1016/j.compstruct.2017.06.043.
• [57] A. Faraz, D. Biermann, and K. Weinert. Cutting edge rounding: An innovative tool wear criterion in drilling CFRP composite laminates. International Journal of Machine Tools and Manufacture, 49(15):1185–1196, 2009. doi: 10.1016/j.ijmachtools.2009.08.002.
• [58] X. Wang, X. Shen, C. Zeng, and F. Sun. Combined influences of tool shape and as-deposited diamond film on cutting performance of drills for CFRP machining. Surface and Coatings Technology, 347:390–397, 2018. doi: 10.1016/j.surfcoat.2018.05.024.

Uwagi

Opracowanie rekordu ze środków MEiN, umowa nr SONP/SP/546092/2022 w ramach programu "Społeczna odpowiedzialność nauki" - moduł: Popularyzacja nauki i promocja sportu (2022-2023).