A New Envelope Computational Method for Meshing Heliacal Gears Profiling Applied to Air Compressor Screw Pair

• Autorzy: Hoang Long

Identyfikatory

DOI

10.12913/22998624/189674

• Języki publikacji: EN

Abstrakty

EN

The theory of enveloping, which determines the envelope to a family of surfaces, the meshing equations of kinematics pairs, including pinion and gear, cutting toll and gear, is widely used in Mechanical Engineering. This paper presents a new envelope computational method for profiling the meshing gear pair. It uses the normal projection of the instantaneous relative rotation axis of the kinematic pair onto the pinion surface to generate the contact line and then automatically computes geometric data of this contact line to create the gear tooth surface. As the profile complexity, the reverse engineering of compressor screw pair was a typical proper example to verify and clarify the proposed method. The method can generate the meshing surface pair with high accuracy: the 3D comparison average error of the surfaces generated by the proposed method and the Boolean method is 0.004 mm, and their RMS error is 0.01 mm. The novel idea of the proposed method is that the contact line, which is used to calculate gear surface, is created easier than solving complex meshing equations, which most previous work used. The proposed method in detail with an algorithm can be used as well for reverse engineering of air compressor screw pair as for parallel axixes heliacal gear pair.

Słowa kluczowe

EN

gear profile; compressor screw; contact line; meshing condition; envelope theory

• Wydawca: Lublin University of Technology ; Polish Society of Ecological Engineering (PTIE), Branch of PTIE in Lublin
• Czasopismo: Advances in Science and Technology. Research Journal
• Rocznik: 2024
• Tom: Vol. 18, no 4
• Strony: 347--354
• Opis fizyczny: Bibliogr. 17 poz., fig., tab.

Twórcy

autor

Hoang Long

• School of Mechanical Engineering, Ha Noi University of Science and Technology, Ha Noi, Vietnam

• https://orcid.org/0000-0002-6521-8591

Bibliografia

• 1. Litvin F.L., Fuentes A. Gear Geometry and Applied Theory, Cambridge University Press, 2004; 818.
• 2. Stosic N., Smith I.K., Kovacevic A. Mujic EGeometry of screw compressor rotors and their tools, Journal of Zhejiang University-SCIENCE A (Applied Physics & Engineering), 2011; 12(4): 31–326.
• 3. Lei L., Meng F., Ni J. A novel non-involute gear designed based on control of relative curvature, Mechanism and Machine Theory, 2019; 140: 144–158.
• 4. Wang J., Hou L., Luo S., Ray Y., Wu C. Active design of tooth profiles using parabolic curve as the line of action, Mechanism and Machine Theory, 2013; 67: 47–63.
• 5. Shu C., He X., Zhang R., Xiao J., Shi G. Study on the reverse design of screw rotor profiles based on a B-spline curve, Advances in Mechanical Engineering, 2019; 11(10), 1–17.
• 6. Hoang L., Banh T.L., Nguyen T.L. A new method for designing and machining air compressor screw pairs, International Journal of Modern Physics B, 2020; 34: 1–5.
• 7. Stosic N., Mujic E., Smith I.K., Kovacevic A. Profiling of screw compressor rotors by use of direct digital simulation, International Compressor Engineering Conference at Purdue, July, 2008; (14–17): 1–8.
• 8. Xuemei C., Deng X., Wei B. A novel method for gear tooth contact analysis and experimental validation, Mechanism and Machine Theory, 2018; 126: 1–13.
• 9. Petrescu F.I., Petrescu R.V. High efficiency gear, Facta Universitatis, Series: Mechanical Engineering, 2014; 12(1): 51–60.
• 10. Miltenović A., Banić M., Tanasković J., Stefanović-Marinović J., Rangelov D., Perić M., wear load capacity of crossed helical gears, Facta Universitatis, Series: Mechanical Engineering, 2022; 1–14. https://doi.org/10.22190/FUME220114015M
• 11. Miltenović A., Tica M., Banić M., Miltenović Đ. Prediction of temperature distribution in the worm gear meshing, Facta Universitatis, Series: Mechanical Engineering, 2020; 18(2): 329–339.
• 12. Veliko I., Genycho N. Profiling of rotation tools for forming helical surfaces, Int. J. Mach. Tools Manuf., 1998; 38: 1125-1148.
• 13. Mohan L.V., Shunmugam M.S. CAD approach for simulation of generation machining and identification of contact lines, International Journal of Machine Tools & Manufacture, 2004; 44: 717–723.
• 14. Mohan M.S., Shunmugam L.V. Simulation of whirling process and tool profiling for machining of worms, Journal of Materials Processing Technology, 2007; 185: 191–197.
• 15. Stoic N. A geometric approach to calculating tool wear in screw rotor machining, International Journal of Machine Tools & Manufacture, 2006; 46: 1961–1965.
• 16. Stoic N. Evaluating errors in screw rotor machining by tool to rotor transformation, Proc. IMechE Part B, Journal of Engineering Manufacture, 2006; 220: 1589–1596.
• 17. Berbinschi S., Teodor V.G., Oancea N. 3D graphical method for profiling tools that generate helical surfaces, Int. J. Adv. Manuf. Technol., 2012; 60: 505–512.

Uwagi

Opracowanie rekordu ze środków MNiSW, umowa nr SONP/SP/546092/2022 w ramach programu "Społeczna odpowiedzialność nauki" - moduł: Popularyzacja nauki i promocja sportu (2024).