Enhancing efficiency by implementation of integrated management system in order to align organisational culture and daily practice

• Autorzy: Zaloga Viliam , Dyadyura Konstiantyn , Rybalka Iryna , Pandova Iveta , Zaborowski Tadeusz

Identyfikatory

DOI

10.2478/mspe-2020-0043

• Języki publikacji: EN

Abstrakty

EN

The main aim of presented article is present methodology how sophisticated products as compressor equipment can be considered and analyzed as a complex technical system which consists of jointly operating components – a set of hardware, software, operational staff and documented information. In process modeling, these components can be in different processes of inputs, outputs, mechanisms (resources) or management. Based on the regulatory requirements for each component of the system, a key indicator efficiency can be identified. This will allow to control the process and make appropriate decisions to improve the system. The application of the proposed methodology for the development and implementation of an integrated management system reduce the cost of resources and significantly improve the quality of the implementation of processes.

Słowa kluczowe

EN

complex technical system; integrated management system; standards; sustainable operations; product life cycle management (PLM)

• Wydawca: STE GROUP
• Czasopismo: Management Systems in Production Engineering
• Rocznik: 2020
• Tom: nr 4 (28)
• Strony: 304--311
• Opis fizyczny: Bibliogr. 39 poz., rys.

Twórcy

autor

Zaloga Viliam

• Sumy State University Sumy State University Faculty of Technical Systems and Energy Efficient Technologies 2, Rymskogo-Korsakova st., 40007 Sumy, Ukraine

autor

Dyadyura Konstiantyn

• Sumy State University Sumy State University Faculty of Technical Systems and Energy Efficient Technologies 2, Rymskogo-Korsakova st., 40007 Sumy, Ukraine

autor

Rybalka Iryna

• Sumy State University Sumy State University Faculty of Technical Systems and Energy Efficient Technologies 2, Rymskogo-Korsakova st., 40007 Sumy, Ukraine

autor

Pandova Iveta

• Technical University of Kosice, Faculty of Manufacturing Technologies with a seat in Presov Sturova 31, 08001 Presov, Slovak Republic

autor

Zaborowski Tadeusz

• Polish Academy of Sciences Branch in Poznan Stary Rynek 78, Palac Dzialynskich, 61-722 Poznan, Poland

Bibliografia

• [1] M. Bengtsson, E. Alfredsson, M. Cohen, S. Lorek, P. Schroeder. "Transforming systems of consumption and production for achieving the sustainable development goals: moving beyond efficiency". Sustainability Science, vol. 13, pp. 1533-1547, 2018.
• [2] A. Panda, K. Dyadyura, J. Valicek, M. Harnicarova, J. Zajac, V. Modrak, I. Pandova, P. Vrabel, E. Novakova-Marcincinova and Z. Pavelek. "Manufacturing Technology of Composite Materials-Principles of Modification of Polymer Composite Materials Technology Based on Polytetrafluoroethylene". Materials, vol. 10, no. 4, pp. 337, 2017.
• [3] J. Valicek, M. Harnicarova, A. Panda, I. Hlavaty, M. Kusnerova, H. Tozan, M. Yagimli and V. Vaclavik. "Mechanism of Creating the Topography of an Abrasive Water Jet Cut Surface". Machining, joining and modifications of advanced materials, vol. 61, pp. 111-120, 2016.
• [4] L.Y. Wang, H.H. Huang, R.W. West, D.Z. Wang. "Intelligent manufacturing system of impeller for computer numerical control (CNC) programming based on KBE". J. Cent. South Univ., vol. 21, pp. 4577-4584, 2014.
• [5] M. Borsato. "Bridging the gap between product lifecycle management and sustainability in manufacturing through ontology building". Computers in Industries, vol. 65, no. 2, pp. 258-269, 2014.
• [6] E. Pallaro and N. Subramanian "Sustainable production and consumption in the automotive sector: Integrated review framework and research directions". Sustainable Production and Consumption, vol. 4, pp. 47-61, 2015.
• [7] J. Walls and R. Paquin. "Organizational perspectives of industrial symbiosis: a review and synthesis". Org Environ., vol. 28, no. 1, pp. 32-53, 2015.
• [8] V. Moreau, M. Sahakian, P. van Griethuysen, F. Vuille. "Coming full circle: why social and institutional dimensions matter for the circular economy". J Ind Ecol., vol. 21, no. 3, pp. 497-506, 2017.
• [9] K. Govindan and M. Hasanagic. "A systemic review on drivers, barriers, and practices towards circular economy: a supply chain perspective". Int J Prod Res, vol. 56, no. 1-2, pp. 278-311, 2018.
• [10] A. Panda, J. Duplak, J. Jurko and M. Behun. "Comprehensive Identification of Sintered Carbide Durability in Machining Process of Bearings Steel 100CrMn6", Advanced Materials Research, vol. 340, pp. 30-33, 2011.
• [11] K. Xing, H.-F. Wang, W. Qian. "A sustainability-oriented multi-dimensional value assessment model for product-service development". International Journal of Production Research, vol. 51, no. 19, pp. 5908-5933, 2013.
• [12] O. Dynnyk, Y. Denysenko, V. Zaloga, O. Ivchenko and T. Yashyna. "Information support for the quality management system assessment of engineering enterprises". DSMIE 2019: Advances in Design, Simulation and Manufacturing II. Lecture Notes in Mechanical Engineering, pp. 65-74, 2019.
• [13] Y. Denysenko, O. Dynnyk, T. Yashyna, N. Malovana and V. Zaloga. Implementation of CALS-Technologies in quality management of product life cycle processes. DSMIE 2019: Advances in Design, Simulation and Manufacturing II. Lecture Notes in Mechanical Engineering, pp. 3-12, 2019.
• [14] E. Sujová and H. Čierna. "Optimization and Improvement of Test Processes on a Production Line". Management Systems in Production Engineering, vol. 26, no. 2, pp. 88-92, 2019.
• [15] T.P. Sharashkina. "Methodical aspects of organization and carrying out of functional-cost analysis on the basis of process approach for the purpose of expenses and quality optimization". European Research Studies, vol. XIX, issue 3, part B, pp. 77-96, 2016.
• [16] M. Balara, D. Duplakova and D. Matiskova. "Application of a signal averaging device in robotics 2018". Measurement, vol. 115, pp. 125-132, 2018.
• [17] A. Panda, Š. Olejárová, J. Valíček and M. Harničárová. "Monitoring of the condition of turning machine bearing housing through vibrations". International Journal of Advanced Manufacturing Technology, vol. 97, no. 1-4, pp. 401-411, 2018.
• [18] H. Dong Wang, G. Le Chang, J. Ping Deng, J. Jie Zheng and Y. Lin Zhao. "Theoretical Research on New Method of Highway Engineering Quality Supervision and Management-Comprehensive Six Sigma Quality Management". Applied Mechanics and Materials, vols. 584-586, pp. 2250-2263, 2014.
• [19] J. Valicek, M. Harnicarova, I. Kopal, Z. Palková, M. Kušnerová, A. Panda and V. Šepelák. "Identification of Upper and Lower Level Yield strength in Materials". Materials, vol. 10, no. 9, pp. 1-20, 2017.
• [20] M. Durdan, B. Stehlikova, M. Pastor, J. Kacur, M. Laciak and P. Flegner. "Research of annealing process in laboratory conditions". Measurement, vol. 73, 2015, pp. 607-618.
• [21] A. Panda, J. Dobránsky, M. Jančík, I. Pandová and M. Kačalová. "Advantages and effectiveness of the powder metallurgy in manufacturing technologies". Metalurgija, vol. 57, no. 4, pp. 353-356, 2018.
• [22] J. Valicek, M. Harnicarova, I. Hlavaty, R. Grznárik, M. Kusnerova, Z. Mitaľová and A. Panda. "A new approach for the determination of technological parameters for hydroabrasive cutting of materials". Materialwissenschaft und Werkstofftechnik, vol. 47, pp. 462-471, 2016.
• [23] I. Pandova, T. Gondova and K. Dubayova. "Natural and Modified Clinoptilolite Testing for Reduction of Harmful Substance in Manufacturing Exploitation". Advanced Materials Research, vols. 518-523, pp. 1757-1760, 2012.
• [24] J. Macala, I. Pandova, T. Gondova and K. Dubayova. "Reduction of polycyclic aromatic hydrocarbons and nitrogen monooxide in combustion engine exhaust gases by clinoptilolite". Gospodarka Surowcami Mineralnymi, vol. 28, no. 2, pp. 113-123, 2012.
• [25] J. Macala, I. Pandova and A. Panda. "Zeolite as a prospective material for the purification of automobile exhaust gases". Mineral resources management, vol. 33, no. 1, pp. 125-138, 2017.
• [26] Z. Murcinkova and T. Krenicky. “Applications utilizing the damping of composite microstructures for mechanisms of production machines and manipulator devices.” In: 13 th Int. Multidisciplinary Sci. Geoconf. SGEM 2013, Albena, Bulgaria. June 16-22, 2013. Book Series: Int. Multidisciplinary Scientific GeoConference-SGEM, pp. 23-30, 2013.
• [27] A. Panda, V. Nahornyi, I. Pandová, M. Harničárová, M. Kušnerová, J. Valíček and J. Kmec. "Development of the method for predicting the resource of mechanical systems". International Journal of Advanced Manufacturing Technology, vol. 105, no. 1-4, pp. 1563-1571, 2019.
• [28] T. Krenicky. “Monitoring of Technical Systems Operation Using Virtual Instrumentation”. Strojarstvo extra, no. 5, pp. 25/1-25/2, 2010. ISSN 1335-2938.
• [29] S. Olejarova, J. Dobransky, J. Svetlik and M. Pituk. "Measurements and evaluation of measurements of vibrations in steel milling process". Measurement, vol. 106, pp. 18-25, 2017.
• [30] M. Rimar, M. Fedak, A. Kulikov and P. Smeringai. "Study of gaseous flows in closed area with forced ventilation." MM Science Journal, vol. 2018, no. March, pp. 2188-2191, 2018.
• [31] J. Dobránsky, M. Pollák and Z. Doboš. "Assessment of production process capability in the serial production of components for the automotive industry". Management Systems in Production Engineering, vol. 27, no. 4, pp. 255-258, 2019.
• [32] M. Pollák, J. Torok, J. Zajac, M. Kočiško and M. Teliskova. "The structural design of 3D print head and execution of printing via the robotic arm ABB IRB 140". ICIEA 2018, vol. 2018, pp. 194-198, 2018.
• [33] W. Bialy and J. Ružbarský. "Breakdown cause and effect analysis. Case study". Management Systems in Production Engineering, vol. 26, pp. 83-87, 2018.
• [34] D. Duplakova, L. Knapcikova, M. Hatala and E. Szilagyi. "Mathematical modelling of temperature characteristics of RFID tags with their subsequent application in engineering production". TEM Journal-Technology Education Management Informatics, vol. 5, pp. 411-416, 2016.
• [35] J. Kascak, P. Baron, M. Teliskova, J. Zajac, J. Torok and J. Husar. "Implementation of augmented reality into the training and educational process in order to support spatial perception in technical documentation". 6 th IEEE international conference on industrial engineering and applications, pp. 583- 587, 2019.
• [36] R. Bielousova. "Developing materials for English for specific purposes online course within the blended learning concept". TEM Journal-Technology Education Management Informatics, vol. 6, pp. 637-642, 2017.
• [37] Ľ. Straka, I. Čorný and J. Piteľ. "Properties evaluation of thin micro hardened surface layer of tool steel after wire EDM". Metals, vol. 6, no. 5, pp. 1-16, 2016.
• [38] K. Monkova and P. Monka. "Some aspects influencing production of porous structures with complex shapes of cells". Lecture Notes in Mechanical Engineering, pp. 267-276, 2017.
• [39] Ľ. Straka, I. Čorný and J. Piteľ. "Prediction of the geometrical accuracy of the machined surface of the tool steel EN X30WCrV9-3 after electrical discharge machining with CuZn37 wire electrode". Metals, vol. 7, no. 11, pp. 1-19, 2017.

Uwagi

Opracowanie rekordu ze środków MNiSW, umowa Nr 461252 w ramach programu "Społeczna odpowiedzialność nauki" - moduł: Popularyzacja nauki i promocja sportu (2021).