The Effect of Adding Iron Powder From Plasma Cutting on the Microstructure, Mechanical Properties of the Composite Based on Aluminum Powder Matrix Made Using Powder Metallurgy

• Autorzy: Wędrychowicz M. , Bydałek A. W. , Migas P. , Skrzekut T. , Noga P. , Madej P. , Kałasznikow A.

Identyfikatory

DOI

10.24425/amm.2021.134785

• Języki publikacji: EN

Abstrakty

EN

The paper presents the results of research on the effect of added iron powder from plasma cutting on the mechanical properties and structure of a composite rod based on aluminum powder. The iron powder came from plasma cutting of steel elements and was handed over by the enterprise “AK Anatol” from Żary. One of the ways to dispose of it is to use it as a filler in aluminum composite rods. Research shows that Fe can be distributed in aluminum evenly, and increase in mechanical properties is achieved at the expense of only a slight increase in density. The proposed system does not reduce the amount of waste produced by plasma cutting but finds a use for some of it. The sintering point of the powder required a strongly reducing atmosphere (Po₂ < 10^-50 atm) which seems virtually unachievable under laboratory conditions. The reinforcing mechanism is related to the fragmentation of the matrix aggregate particles and the uniform distribution of Fe particles in the aluminum matrix.

Słowa kluczowe

EN

Al-Fe composite; iron powder; plasma cutting; aluminum matrix composites; powder metallurgy; mechanical properties

• Wydawca: Institute of Metallurgy and Materials Science of Polish Academy of Sciences ; Committee of Materials Engineering and Metallurgy of Polish Academy of Sciences
• Czasopismo: Archives of Metallurgy and Materials
• Rocznik: 2021
• Tom: Vol. 66, iss. 1
• Strony: 273--279
• Opis fizyczny: Bibliogr. 29 poz., fot., rys., tab., wykr.

Twórcy

autor

Wędrychowicz M.

• University of Zielona Góra, Faculty of Mechanical Engineering, 4 Prof. Z. Szafrana Str., 65-516 Zielona Góra, Poland

autor

Bydałek A. W.

• University of Zielona Góra, Faculty of Mechanical Engineering, 4 Prof. Z. Szafrana Str., 65-516 Zielona Góra, Poland
• West Pomeranian University of Technology in Szczecin, Faculty of Maritime Technology and Transport, Al. Piastów 41, 71-065 Szczecin

autor

Migas P.

• AGH University of Science and Technology, Faculty of Metals Engineering and Industrial Computer Science, Al. Mickiewicza 30, 30-059 Kraków, Poland

autor

Skrzekut T.

• AGH University of Science and Technology, Faculty of Non-Ferrous Metals, Al. Mickiewicza 30, 30-059 Kraków, Poland

autor

Noga P.

• AGH University of Science and Technology, Faculty of Non-Ferrous Metals, Al. Mickiewicza 30, 30-059 Kraków, Poland

autor

Madej P.

• Łukasiewicz Research Network-Institute of Non-Ferrous Metals, Pyrometallurgy Department, 5 Sowińskiego Str., 44-100 Gliwice, Poland

autor

Kałasznikow A.

• University of Zielona Góra, Faculty of Mechanical Engineering, 4 Prof. Z. Szafrana Str., 65-516 Zielona Góra, Poland

Bibliografia

• [1] T.T. Sasaki, T. Ohkubo, K. Hono, Acta Mater. 57 (12), 3529-3538 (2009).
• [2] I. Adamovich, S. D. Baalrud, A. Bogaerts, A. M. Vardelle, J. Phys. D Appl. Phys. 50 (32), 1-46 (2017).
• [3] A. Klimpel, Welding and metal cutting technology 14, 501-515 (1997).
• [4] https://www3.epa.gov/ttn/chief/efdocs/welding.pdf, accessed: 17.10.2019.
• [5] DIN EN ISO 9013:2017, Thermisches schneiden - Einteilung thermischer Schnitte - Geometrische Produktspezifikation und Qualitat, 2017 r.
• [6] EN ISO 17639:2013-12, Zerstorende Prufung von Schweissverbindung an metallischen Werkstofen - Makroskopische und mikroskopische Untersuchunge von Schweissnahten.
• [7] A. Kałasznikow, S. Kłos, Innovations in management and production engineering 1, 554-563 (2018).
• [8] S. Stauss, H. Muneoka, K. Urabe, K. Terashima, Physic of Plasma 22 (5), 1-13 (2015).
• [9] Q. Chen, J. Li, Y. Li, J. Phys. D Appl. Phys. 48 (42), 1-25 (2014).
• [10] J. Torralba, C.E. Da Costab, F. Velasco, Mater. Process. Technol. 133 (1-2), 203-206 (2003).
• [11] J.R. Pickens, J. Mater. Sci. 16, 1437-1457(1981).
• [12] Y.B. Liu, S.C. Lim, L. Lu, M.O. Lai, J. Mater. Sci. 29 (8), 1999-2007 (1994).
• [13] B. Huang, N. Tokizane, K.N. Ishihara, P.H. Shingu, S. Nasu, J. Non-Cryst. Solids 117-118 (2), 688-691 (1990).
• [14] D.K. Mukhopadhyay, C. Suryanarayana, F.H. Froes, Metall. Mater.Trans. A 26 (8), 1939-1946 (1995).
• [15] B.S. Murty, S. Ranganathan, Int. Mater. Rev. 43 (3), 101-141 (1998).
• [16] K.N. Ishihara, F. Kubo, E. Yamasue, and H. Okumura, Rev. Adv. Mater. Sci. 18 (3), 284 (2008).
• [17] E. Bayraktar, D. Katundi, J. Achiev. Mater. Manuf. Eng. 38, 7-14 (2010).
• [18] A. Mazahery, M.O. Shabani, Ceram Int. 38 (5), 4263-4269 (2012).
• [19] A. Mazahery, M.O. Shabani, Powder Technol. 217, 558-565 (2012).
• [20] A. Fathy, O. El-Kady, M.M. Mohammed, Trans. Nonferrous Met. Soc. China 25, 46-53 (2015).
• [21] A.K. Kaw (Ed.), Mechanics of composite materials, 2nd ed., Taylor & Francis Group, New York (2006).
• [22] G.E. Dieter (Ed.), Mechanical Metallurgy: Principles and Applications 3rd ed., McGraw-Hill, New York (1976).
• [23] A. Zajączkowski, J. Norwisz, J. Botor, Non-ferrous Ores and Metals 31, 275-277 (1986).
• [24] G. Włoch, T. Skrzekut, J. Sobota, A. Woźnicki, J. Cisoń, Key Eng. Mater. 682, 245-251 (2016).
• [25] T. Skrzekut, A. Kula, L. Błaż, Key Eng. Mater. 682, 259-264 (2016).
• [26] W. Khraisat, J. Abu Jadayil, J. Mech. Ind. Eng. Res. 4 (3), 372-377 (2010).
• [27] E.M. Ruiz-Navas, M.L. Delgado, J.M. Torralba, Adv. Mat. Res. 23, 51-58 (2007).
• [28] M. Qian, G.B Shaffer, Sintering of aluminium and its alloys, in: Zhigang Zak Fang (Ed.), Sintering of Advanced Materials (2010), Woodhead Pulblishing (2010).
• [29] X. Li, A. Scherf, M. Hellmaier, F. Stein, J. Phase Equilib. Diffus 3, 1 62-164 (2016).

Uwagi

Opracowanie rekordu ze środków MNiSW, umowa Nr 461252 w ramach programu "Społeczna odpowiedzialność nauki" - moduł: Popularyzacja nauki i promocja sportu (2021).