PL EN


Preferencje help
Widoczny [Schowaj] Abstrakt
Liczba wyników
Tytuł artykułu

Comparative analysis of cold and warm rolling on tensile properties and microstructure of additive manufactured Inconel 718

Wybrane pełne teksty z tego czasopisma
Identyfikatory
Warianty tytułu
Języki publikacji
EN
Abstrakty
EN
Despite the high efficiency and low cost of wire + arc additive manufacture (WAAM), the epitaxial grown columnar dendrites of WAAM deposited Inconel 718 cause inferior properties and severe anisotropy compared to the wrought components. Fundamental studies on the influence of one-pass cold and warm rolling on hardness and microstructure were investigated. Then the interpass cold and warm rolling on tensile properties were also analyzed. The results show that the one-pass rolling increases the hardness and displays a heterogeneous hardness distribution compared to the as-deposited material, and the warm rolling exhibits a larger and deeper strain compared to cold rolling. The columnar dendrites gradually change to cell dendrites under the rolling process and then change to equiaxed grains with the subsequent new layer deposition. The average grain size is 16.8 μm and 23.5 μm for the warm and cold rolling, respectively. The strongly textured columnar dendrites with preferred < 001 > orientation transform to equiaxed grains with random orientation after rolling process. The grain refinement contributes to the dispersive distributed strengthening phases and the increase in its fraction with heat treatment. The as-deposited samples show superior tensile properties compared to the cast material but inferior compared to the wrought components, while the warm-rolled samples show superior tensile properties to wrought material. Isotropic tensile properties are obtained in warm rolling compared to cold rolling. The rolling process and heat treatment both decrease the elongation and lead to a transgranular ductile fracture mode. Finally, the rolling-induced strengthening mechanism was discussed.
Rocznik
Strony
art. no. e44, 2022
Opis fizyczny
Bibliogr. 34 poz., rys., wykr.
Twórcy
autor
  • Light Alloy Research Institute, Central South University, Changsha 410083, China
  • State Key Laboratory of High Performance Complex Manufacturing, Central South University, Changsha 410083, China
autor
  • Light Alloy Research Institute, Central South University, Changsha 410083, China
  • State Key Laboratory of High Performance Complex Manufacturing, Central South University, Changsha 410083, China
autor
  • Light Alloy Research Institute, Central South University, Changsha 410083, China
  • State Key Laboratory of High Performance Complex Manufacturing, Central South University, Changsha 410083, China
autor
  • Light Alloy Research Institute, Central South University, Changsha 410083, China
  • State Key Laboratory of High Performance Complex Manufacturing, Central South University, Changsha 410083, China
  • Department of Mechanical Engineering, Kano University of Science and Technology, Wudil, Nigeria
autor
  • Welding Engineering and Laser Processing Centre, Cranfield University, Bedford MK43 0AL, UK
  • School of Materials Science and Engineering, Nanjing University of Science and Technology, Nanjing 210094, China
Bibliografia
  • 1. Yang X, Wang B, Jiang W, Shen S, Wang J. The superplasticity improvement of Inconel 718 through grain refinement by large reduction cold rolling and two-stage annealing. Mater Sci Eng A.2021;823:141713.
  • 2. Shen XH, Gong XH, Wang BL, He JQ, Xu CH, Su GS. Surface properties enhancement of Inconel 718 alloy by ultrasonic roller burnishing coupled with heat treatment. Arch Civ Mech Eng.2021;21:1–17.
  • 3. Cui XL, Yuan S. Analysis of thickness variation and stress state in hydroforming of complex T-shaped tubular part of nickel-based superalloy. Arch Civ Mech Eng. 2021;21:111.
  • 4. Kuo YL, Horikawa S, Kakehi K. The effect of interdendritic δ phase on the mechanical properties of alloy 718 built up by additive manufacturing. Mater Design. 2017;116:411–8.
  • 5. Dang J, Cai X, Yu D, An Q, Ming W, Chen M. Effect of material microstructure on tool wear behavior during machining additively manufactured Ti6Al4V. Arch Civ Mech Eng. 2020;20:1–15.
  • 6. Song B, Yu T, Jiang X, Xi W, Lin X. The relationship between convection mechanism and solidification structure of iron-based molten pool by laser direct deposition. Int J Mech Sci. 2019;165:105207.
  • 7. Cao GH, Sun TY, Wang CH, Li X, Liu M, Zhang ZX, Hu PF, Russell AM, Schneider R, Gerthsen D. Investigations of γ′, γ′′ and δ precipitates in heat-treated Inconel 718 alloy fabricated by selective laser melting. Mater Charact. 2018;136:398–406.
  • 8. Manurung Y, Prajadhiana KP, Adenan MS, Awiszus B, Haelsig A. Analysis of material property models on WAAM distortion using nonlinear numerical computation and experimental verification with P-GMAW. Arch Civ Mech Eng. 2021;21:32.
  • 9. Wu B, Pan Z, Ding D, Cuiuri D, Li H, Xu J, Norrish J. A review of the wire arc additive manufacturing of metals: properties, defects and quality improvement. J Manuf Process. 2018;35:127–39.
  • 10. Williams S, Martina F, Addison A, Ding J, Pardal G, Colegrove P. Wire + arc additive manufacturing. Mater Sci Tech Lond. 2016;7:641–7.
  • 11. Clark D, Bache MR, Whittaker MT. Shaped metal deposition of a nickel alloy for aero engine applications. J Mater Process Tech. 2008;203:439–48.
  • 12. Asala G, Khan AK, Andersson J, Ojo OA. Microstructural analyses of ATI 718Plus® produced by wire-ARC additive manufacturing process. Metall Mater Trans A. 2017;48:4211–28.
  • 13. Xu X, Ding J, Ganguly S, Williams S. Investigation of process factors affecting mechanical properties of INCONEL 718 superalloy in wire+ arc additive manufacture process. J Mater Process Tech. 2019;265:201–9.
  • 14. Oguntuase O, Ojo OA, Beddoes J. Influence of post-deposition heat treatments on the microstructure and mechanical properties of wire–arc additively manufactured ATI 718Plus. Metall Mater Trans A. 2020;51:1846–59.
  • 15. Chen C, Pan Z, Ding D, Yuan L, Li H. The influence of post-production heat treatment on the multi-directional properties of nickel-aluminum bronze alloy fabricated using wire-arc additive manufacturing process. Addit Manuf. 2018;23:411–21.
  • 16. Asala G, Andersson J, Ojo OA. Hot corrosion behaviour of wire-arc additive manufactured Ni-based superalloy ATI 718Plus. Corros Sci. 2019;158:108086.
  • 17. Colegrove PA, Coules HE, Fairman J, Martina F, Kashoob T, Mamash H, Cozzolino LD. Microstructure and residua stress improvement in wire and arc additively manufactured parts through high-pressure rolling. J Mater Process Tech. 2013;213:1782–91.
  • 18. Abbaszadeh M, Honnige JR, Martina F, Neto L, Kashaev N, Colegrove P, Williams S, Klusemann B. Numerical investigation of the effect of rolling on the localized stress and strain induction for wire + arc additive manufactured structures. J Mater Eng Perform. 2019;28:4931–42.
  • 19. Tangestani R, Farrahi GH, Shishegar M, Aghchehkandi BP, Mehmanparast A. Effects of vertical and pinch rolling on residua stress distributions in wire and arc additively manufactured components. J Mater Eng Perform. 2020;29:2073–84.
  • 20. Martina F, Colegrove PA, Williams SW, Meyer J. Microstructure of interpass rolled wire + arc additive manufacturing Ti-6Al-4Vcomponents. Metall Mater Trans A. 2015;46:6103–18.
  • 21. Gu J, Ding J, Williams SW, Gu H, Ma P, Zhai Y. The effect of inter-layer cold working and post-deposition heat treatment on porosity in additively manufactured aluminum alloys. J Mater Process Tech. 2016;230:26–34.
  • 22. Gu J, Wang X, Bai J, Ding J, Williams SW, Zhai Y, Kun L. Deformation microstructures and strengthening mechanisms for the wire+arc additively manufactured Al-Mg4.5Mn alloy with inter-layer rolling. Mater Sci Eng A. 2018;712:292–301.
  • 23. Dirisu P, Supriyo G, Martina F, Xu X, Williams S. Wire plus arc additive manufactured functional steel surfaces enhanced by rolling. Int J Fatigue. 2020;130:105237.
  • 24. Xu X, Ganguly S, Ding J, Seow C, Williams S. Enhancing mechanical properties of wire+ arc additively manufactured INCONEL 718 superalloy through in-process thermomechanical processing. Mater Des. 2018;160:1042–51.
  • 25. Lin YC, He DG, Chen MS. EBSD analysis of evolution of dynamic recrystallization grains and delta phase in a nickel-based superalloy during hot compressive deformation. Mater Des. 2016;97:13–24.
  • 26. Chen XM, Lin YC, Wu F. EBSD study of grain growth behavior and annealing twin evolution after full recrystallization in a nickel-based superalloy. J Alloy Compd. 2017;724:198–207.
  • 27. Varga J, Kingstedt OT. An investigation of the plastic work to heat conversion of wrought and laser powder bed fusion manufactured Inconel 718. Addit Manuf. 2021;46:102179.
  • 28. Seow CE, Coules HE, Wu G, Khan RHU, Williams S. Wire + arc additively manufactured Inconel 718: effect of post-deposition heat treatments on microstructure and tensile properties. Mater Design. 2019;183:108157.
  • 29. SAE. Aerospace, Aerospace Material Specification: AMS 5662. SAE International 2009.
  • 30. SAE. Aerospace, Aerospace Material Specification: AMS 5383. SAE International 2012.
  • 31. Zhang D, Niu W, Cao X, Liu Z. Effect of standard heat treatment on the microstructure and mechanical properties of selective laser melting manufactured Inconel 718 superalloy. Mater Sci Eng A. 2015;644:32–40.
  • 32. Wang Y, Shi J. Recrystallization behavior and tensile properties of laser metal deposited Inconel 718 upon in-situ ultrasonic impact peening and heat treatment. Mater Sci Eng A. 2020;786:139434.
  • 33. Qi H, Azer M, Ritter A. Studies of standard heat treatment effects on microstructure and mechanical properties of laser net shape manufactured INCONEL 718. Metall Mater Trans A. 2009;40:2410–22.
  • 34. Cong B, Ding J, Williams S. Effect of arc mode in cold metal transfer process on porosity of additively manufactured Al-6.3%Cu alloy. Int J Adv Manuf Tech. 2015;76:1593–606.
Uwagi
PL
Opracowanie rekordu ze środków MEiN, umowa nr SONP/SP/546092/2022 w ramach programu "Społeczna odpowiedzialność nauki" - moduł: Popularyzacja nauki i promocja sportu (2022-2023)
Typ dokumentu
Bibliografia
Identyfikator YADDA
bwmeta1.element.baztech-cda095e5-7793-4cba-a941-74cf13925508
JavaScript jest wyłączony w Twojej przeglądarce internetowej. Włącz go, a następnie odśwież stronę, aby móc w pełni z niej korzystać.