Digitization procedure of creating 3D model of dental bridgework reconstruction

• Autorzy: Dobrzański L. A. , Reimann Ł.
• Języki publikacji: EN

Abstrakty

EN

Purpose: The still growing patient requirements is concerned with aesthetics but also with strength of the prosthetic restorations. Resistance on stresses depends among others on the shape, so it is necessary to transfer the dentures of a physical model to a computer environment and a simulation of the work conditions. The aim of that work was to study the methodology of digitization of a plaster model into a numerical model, using CAD/CAM dental system and CAD application, which can be in a next step imported to ANSYS application in order to realize stress analysis. Design/methodology/approach: To realize the transfer of a physical model of the dental bridge to a computer environment the 3i Incise Renishaw scanner which saved the plaster model by a probe about 1 or 3 mm diameter, moved in the scanner arm and contacted with it was used. A scanned plaster mode was exported into STL file and then opened in DentCAD Delcam application. Using the CAD module the preparation line was marked, a pontic was orientated in a right position and connectors of the pillar teeth and the pontic. Geometry and the cross section of the connectors depend on the bridgework strength. A designed bridge reconstruction was imported to CAD application and there curves were firstly drawn, then changed into NURBS surfaces and finally surfaces were merged into one solid model. A ready model can be imported up to ANSYS software in order to realize the stress analysis. Findings: A prepared dental case from a physical one was changed into a numerical model in following steps: scanning a plaster model by a contact scanner, designing the bridgeworks in CAD dental software environment, importing in CAD application, building the solid model and at the end importing in ANSYS software. Selected digitization procedure let to make all engineering calculations and analysis without manufacturing the physical model, what considerably reduce cost of the research investigations. Practical implications: A realized work gave an information about possibilities of verification for a physical model of restoration and a numerical model which can be compared to results from software simulation of behaviour of the bridgework in different load cases. Originality/value: The paper presents that it is not necessary to have a physical reconstruction model, to check the resistance on stress because it is possible to use the CAD/CAM dental system to design the dentures and then modelling the boundary conditions and observe the stress analysis.

Słowa kluczowe

EN

CAD/CAM; dental bridge; digitization; prosthodontia

• Wydawca: International OCSCO World Press
• Czasopismo: Journal of Achievements in Materials and Manufacturing Engineering
• Rocznik: 2012
• Tom: Vol. 55, nr 2
• Strony: 469--476
• Opis fizyczny: Bibliogr. 30 poz., rys., tab.

Twórcy

autor

Dobrzański L. A.

• Institute of Engineering Materials and Biomaterials, Silesian University of Technology, ul. Konarskiego 18a, 44-100 Gliwice, Poland

autor

Reimann Ł.

• Institute of Engineering Materials and Biomaterials, Silesian University of Technology, ul. Konarskiego 18a, 44-100 Gliwice, Poland

Bibliografia

• [1] K. Lasek, P. Okoński, E. Mierzwińska-Nastalska, Zirconium oxide: its physico-mechanical properties and clinical application, Prosthodontics 59/6 (2009) 415-422 (in Polish).
• [2] A.D. Dobrzańska-Danikiewicz, J. Żmudzki, Development trends of mucous-borne dentures in the aspect of elastomers applications, Archives of Materials Science and Engineering 55/1 (2012) 5-13.
• [3] L.A. Dobrzański, A.J. Nowak, W. Błażejewski, R. Rybczyński, Non-standard test methods for long-fibrous reinforced composite materials, Archives of Materials Science and Engineering 47/1 (2011) 5-10.
• [4] T. Matković, P. Matković, J. Malina, Effects of Ni and Mo on the microstructure and some other properties of Co-Cr dental alloys, Journal of Alloys and Compounds 366/1-2 (2004) 293-297.
• [5] L.A. Dobrzańki, Ł. Reimann, C. Krawczyk, Effect of age hardening on corrosion resistance and hardness of CoCrMo alloys used In dental engineering, Archives of Materials Science and Engineering 57/1 (2012) 5-12.
• [6] M. Sharma, A.V. Ramesh Kumar, N. Singh, N. Adya, B. Saluja, Electrochemical corrosion behavior of dental/implant alloys in artificial saliva, Journal of Materials Engineering and Performance 17/5 (2008) 695-701.
• [7] W. Walke, Z. Paszenda, J. Tyrlik-Held, Corrosion resistance and chemical composition investigations of passive layer on the implants surface of Co-Cr-W-Ni alloy, Journal of Achievements in Materials and Manufacturing Engineering 16/1-2 (2006) 74-79.
• [8] L.A. Dobrzański, Ł. Reimann, Influence of Cr and Co on hardness and corrosion resistance CoCrMo alloys used on dentures, Journal of Achievements in Materials and Manufacturing Engineering 49/2 (2011) 193-199.
• [9] J. Żmudzki, G. Chladek, J. Kasperski, Silicone attachment for avoidance of bone tissue overloading in single implant-retained denture, Archives of Materials Science and Engineering 51/2 (2011) 107-115.
• [10] J. Kasperski, G. Chladek, J. Żmudzki, The effect of saturation by artificial saliva on the effectiveness of denture adhesives, Archives of Materials Science and Engineering 51/1 (2011) 25-32.
• [11] J. Żmudzki, Material conditionings of functional efficiency of mucous-borne complete denture, Open Access Library, Volume 4/10 (2012) 1-176 (in Polish).
• [12] W. Li, M. Swain, Q. Li, G.P. Steven, Towards automated 3D finite element modeling of direct fiber reinforced composite dental bridge, Journal of Biomedical Materials Research Part B, Applied Biomaterials 74B/1 (2005) 520-528.
• [13] P. Magne, Efficient 3D finite element analysis of dental restorative procedures using micro-CT data, Dental Materials 23 (2007) 539-548.
• [14] H.E. Leea, C.L. Lina, C.H. Wanga, C.H. Chenga, C.H. Chang, Stresses at the cervical lesion of maxillary premolar - a finite element investigation, Journal of Dentistry 30 (2002) 283-290.
• [15] C.L. Lin, C.H. Chang, C.H. Cheng, C.H. Wang, H.E. Lee, Automatic finite element mesh generation for maxillary second premolar, Computer Methods and Programs in Biomedicine 59 (1999) 187-195.
• [16] G.M. Cathey, Dental anatomy, Dental Laboratory Technology Manuals, 1972.
• [17] J.L. Fuller, G.E. Denehy, Concise dental anatomy and morphology, Year Book Medical Publishers Inc, Chicago, 1984.
• [18] A.K. Rao, K. Montgomery, W.P. Brown, E. Herbranson, 3-D interactive atlas of human tooth anatomy, International Congress Series 1256 (2003) 93-98.
• [19] A. Korcin, Model-making and drawing in prosthodontia, Medical Publishers PZWL, Warsaw, 2003 (in Polish).
• [20] D. Piątowska (Ed.), Dental anatomy and conservative dentistry in phantom exercise, Bestom Dentonet.pl, Łódź, 2009 (in Polish).
• [21] N. Verdonschot, W.M. Fennis, R.H. Kuijs, J. Stolk, C.M. Kreulen, N.H. Creugers, Generation of 3-D finite element models of restored human teeth using micro-CT techniques, The International Journal of Prosthodontics 14/4 (2001) 310-315.
• [22] R. Clement, J. Schneider, H.-J. Brambs, A.P. Wunderlich, M. Geiger, F.G. Sander, Quasi-automatic 3D finite element model generation for individual single-rooted teeth and periodontal ligament, Computer Methods and Programs in Biomedicine 73/2 (2004) 135-144.
• [23] C.L. Lin, H.E. Lee, C.H. Wang, C.H. Chang, Integration of CT, CAD system and finite element method to investigate interfacial stresses of resin-bonded prosthesis, Computer Methods and Programs in Biomedicine 72 (2003) 55-64.
• [24] F.P. Rodriguesa, J. Li, N. Silikasc, R.Y. Ballestera, D.C. Watts, Sequential software processing of micro-XCT dental-images for 3D-FE analysis, Dental Materials 25 (2009) e47-e55.
• [25] I. Budak, B. Kosec, M. Sokovic, Application of contemporary engineering techniques and technologies in the field of dental prosthetics, Journal of Achievements in Materials and Manufacturing Engineering 54/2 (2012) 233-241.
• [26] C.-L. Li, H.E. Lee, C.H. Wang, K.H. Chang, Integration of CT, CAD system and finite element method to investigate interfacial stresses of resin-bonded prosthesis, Computer Methods and Programs in Biomedicine 72 (2003) 55-64.
• [27] C.U. Jongh, A.H. Basson, C. Scheffer, Predictive modelling of cervical disc implant wear, Journal of Biomechanics 41/15 (2008) 3177-3183.
• [28] A. Boryor, M. Geiger, A. Hohmann, A. Wunderlich, C. Sander, F.M. Sander, Stress distribution and displacement analysis during an intermaxillary disjunction -A three-dimensional FEM study of a human skull, Journal of Biomechanics Volume 41/2 (2008) 376-382.
• [29] www.renishaw.pl.
• [30] www.dental-cadcam.com.